Hitachi Cpx5 Projector Users Manual

							
4

ItemDescription
SERVICE(continued)
KEY LOCKUsing  the  ▲/▼  buttons  turns  on/off  the  key  lock  feature.  When TURN  ON  is  selected,  the  buttons  on  the  projector  except  the STANDBY/ON button are locked.TURN ON ó TURN OFF• Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control.
REMOTE FREQ.Use the ▲/▼ button to change the Projector's remote sensor setting.
1:NORMAL ó 2:HIGH
Items with a checkmark are on. The factory default setting is for both 1:NORMAL and 2:HIGH to be on.  If the remote control does not function correctly set this to either only 1 or only 2 (12).Neither can be turned off at the same time.
INFORMATIONSelecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATIONCOMPUTER11024x768 @60FRAME LOCK ON
INPUT-INFORMATIONS-VIDEOPALAUTO
INPUT-INFORMATIONCOMPUTER 576i @50
• The “FRAME LOCK” message on the dialog means the frame lock function is working. 
• This item can't be selected for no signal and sync out.
FACTORY RESETSelecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE and SECURITY are not reset.
RESET  CANCEL
OPTION Menu (continued)
OPTION Menu
(continued on next page)
4/16(43
014/#.*+)*
064:œ:¥:«:œ:© 
						

							
4

ItemDescription
SECURITY
This projector is equipped with security functions.User registration is required before using the security functions.Please contact your local dealer.
1. Using Security Features
1.1 Inputting the PASSWORD
1.1-1  Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button. The ENTER PASSWORD box will be displayed.The factory default PASSWORD is 2805. This PASSWORD can be changed (1.2 Changing the PASSWORD). • It is strongly recommended the factory default PASSWORD to be changed as soon as possible.
1.1-2  Use the ▲/▼/◄/► buttons to enter the registered PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX and press the ► button to display the SECURITY menu.  If an incorrect PASSWORD is input the ENTER PASSWORD BOX will be displayed again. If incorrect PASSWORD is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PASSWORD is input.
1.2 Changing the PASSWORD
1.2-1  Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD BOX.
1.2-2  Use the ▲/▼/◄/► buttons to enter the new PASSWORD.
1.2-3  Move the cursor to the right side of the ENTER NEW PASSWORD BOX and press the ► button to display the NEW PASSWORD AGAIN BOX, enter the same PASSWORD again. 
1.2-4  Move the cursor to the right side of the NEW PASSWORD AGAIN BOX and press the ► button and the NOTE NEW PASSWORD BOX will be displayed for about 20 seconds, please make note of the PASSWORD during this time.  Pressing the ENTER button will close the NOTE NEW PASSWORD BOX.• Please do not forget your PASSWORD.
OPTION Menu (continued)
OPTION Menu
5%74+6;0642#55914&
0:6

37+6
5%74+6;
5%74+6;2#55914&%*#0)/[5ETGGP2#55914&67401((2+0.1%-67401((64#05+6+10&6%61467401((
5%74+6;064092#55914&
0:6

37+6
5%74+6;092#55914&#)#+0
1-

%#0%.
5%74+6;016092#55914&
:+6

064
(continued on next page) 
						

							
43

ItemDescription
SECURITY(continued)
1.3 If you have forgotten your PASSWORD
1.3-1  Follow the procedure in 1.1-1 to display the ENTER PASSWORD BOX.
1.3-2  While the ENTER PASSWORD BOX is displayed, press and hold the RESET button for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 secondsThe 10 digit Inquiring Code will be displayed. • If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close. If necessary repeat the process from 1.3-1.
1.3-3  Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
2.1 Turning on the MyScreen PASSWORD 
Function
2.1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.
2.2 Setting the PASSWORD
2.2-1  Display the MyScreen on/off menu using the procedure in 2.1-1.
2.2-2  Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select TURN ON.The ENTER PASSWORD BOX (small) will be displayed.
2.2-3  Use the ▲/▼/◄/► buttons to enter the PASSWORD.  Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
5%74+6;2#55914&

+PSWKTKPI%QFG
OPTION Menu (continued)
OPTION Menu
/[5ETGGP0642#55914&
0:6

37+6
/[5ETGGP%*%-2#55914&
0:6

37+6
/[5ETGGP2#55914&
67401067401((
(continued on next page) 
						

							
44

ItemDescription
SECURITY(continued)
2.2-4  Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button will return to MyScreen PASS WORD on/off menu.When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock function (and menu) will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of both  functions.
• Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
2.3-1  Follow the procedure in 2.1-1 to display the MyScreen PASSWORD on/off menu.
2.3-2  Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the MyScreen on/off menu.If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 2.3-1.
2.4 If you have forgotten your PASSWORD
2.4-1  Follow the procedure in 2.1-1 to display the MyScreen PASSWORD on/off menu.
2.4-2  Select TURN OFF to display the ENTER PASSWORD BOX (large). The 10 digit Inquiring Code will be displayed inside the BOX.
2.4-3  Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unless a registered Code is input.3.1 Registering the PIN Code
3.1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
0:637+6
+PSWKTKPI%QFG         
/[5ETGGP0642#55914&
OPTION Menu (continued)
OPTION Menu
/[5ETGGP%1/2.6
064
2+0.1%-
67401067401((
(continued on next page) 
						

							
45

ItemDescription
SECURITY(continued)
3.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed. 3.1-3    Input a 4 part PIN Code using the ▲, ▼, ◄, ►, COMPUTER/STORAGE and INPUT buttons.A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration.• If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat the process from 3.1-1.Afterwards, anytime the projector is restarted after the power switch is turned off the PIN BOX will be displayed. Enter the registered PIN Code.The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.This function will activate only when the projector is started after the power switch was turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3.2-1  Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.Enter the registered PIN Code to turn the PIN LOCK function off.If an incorrect PASSWORD is entered the menu will close.
3.3 If you have forgotten your PIN Code
3.3-1  While the PIN BOX is displayed, press and hold the RESET button for three seconds or press and hold the INPUT and ► buttons for three seconds. The 10 digit Inquiring Code will be displayed. • If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off.
3.3-2  Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
OPTION Menu (continued)
OPTION Menu
2+0$1:
%1/2764
+PRWV2+0%QFG
2+0$1:

%QPHKTOCVKQP%1/2764
2+0$1:

+PSWKTKPI%QFG
(continued on next page) 
						

							
46

ItemDescription
SECURITY(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.• Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON.
4.1 Turning On the Transition Detector Function
4.1-1  Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu.  Select TURN ON and the current angle and mirror setting will be recorded.• This feature may not function properly if the projector is not in a stable position when TURN ON is selected.
4.1-2  If this function is set to TURN ON when the vertical angle of the projector or mirror setting at which the projector is turned on is different than the previously recorded the Transition Detector Alarm will be displayed and the projector will not display the input signal.
Set the Transition Detector off in the SECURITY menu to display the input signal.If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after the power switch was turned off.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu.
4.2-2  Use the ▲/▼ buttons on the Transition Detector on/off menu to select TURN ON. The ENTER PASSWORD BOX (small) will be displayed.
4.2-3  
Use the ▲/▼/◄/► buttons to enter a PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
4.2-4  Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time.Pressing the ENTER button will return to the Transition Detector on/off menu.• Please do not forget your Transition Detector PASSWORD.
OPTION Menu (continued)
OPTION Menu
64#05+6+10&6%614
67401067401((
2+0$1:
64#05+6+10&6%61410  6JGRTQLGEVQTJCUDGGPVTCPUHGTTGFHTQORTGXKQWUN[KPUVCNNGFRQUKVKQP+H[QWYKUJVQJCXGCUSWCTGKOCIGQPUETGGPCICKPFKUCDNG6TCPUKVKQP&GVGEVQTQP/GPW
64#05+6+10&6%6140642#55914&
0:6

37+6
64#05+6+10&6%614%*%-2#55914&
0:6

37+6
64#05+6+10&6%614%1/2.6
:+6

064
(continued on next page) 
						

							
47

ItemDescription
SECURITY(continued)
4.3 Setting the Transition Detector off
4.3-1  Follow the procedure in 4.1-1 to display the Transition Detector on/off menu.
4.3-2  Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1.
4.4 If you have forgotten your PASSWORD
4.4-1  Follow the procedure in 4.1-1 to display the Transition Detector on/off menu.
4.4-2  Select TURN OFF to display the ENTER PASSWORD BOX (large). The 10 digit Inquiring Code will be displayed inside the BOX.
4.4-3  Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
USB STORAGE
Pressing the ► button displays the USB STORAGE KEY CONFIG. Menu. For more information, please see the “1) Button operation for still image” of the “Displaying an image in full screen” under the “USB STORAGE” (48).
OPTION Menu (continued)
OPTION Menu
0:637+6
+PSWKTKPI%QFG         
64#05+6+10&6%6140642#55914&
75$5614#)-;%10(+)
$#%-0:6
$#%-
0:6

 
						

							
48

USB STORAGE
This projector has “PC Less presentation” feature that can display following files 
stored in USB storage or display as thumbnail without connecting PC.
NOTE 1
• Compliant file format
File FormatMaximum pixel size
JPEG8176 x 8176
M-JPEG (Motion-JPEG)640 x 480
MPEG4352 x 288
Progressive JPEG file cannot be reproduced.
Some JPEG files may not possible to display the image clearly.
• Compliant Audio format
Audio FormatContainer format (file extension)
8bit or 16bit linear PCMAVI, MP4
μ-lawAVI, MP4
IMA-ADPCMAVI
4bit G.726 ADPCMASF
MPEG1 Layer II Audio
MPEG1 Layer III Audio and AAC(Advanced Audio Coding) can not be reproduced.
In combinations of file format and audio format described in the above lists, 
some files can not be reproduced.
• USB STORAGE
- USB1.1 compliant USB storage media (Mass Storage class) can be used.- Some USB memories may not work correctly.- Security USB memory is not supported.- It is strongly recommended to use AC Power Adaptor with USB Hard Disc.- It may be happened that movie files or sound files cannot be reproduced properly if USB storage does not have enough access speed.- The following formats are recommended for USB storage USB memory FAT12/FAT16/FAT32  (NTFS format is not supported.) USB hard disk FAT12/FAT16/FAT32  (NTFS format is not supported.)
Displaying Thumbnail Menu
1)  Save image files in a USB storage.  Insert the USB storage into USB 
STORAGE port on the projector.
2)  Change input port for the projector to USB STORAGE using COMPUTER/
STORAGE button on the remote control or INPUT/ENTER button on the 
projector (5) so that Thumbnail menu below is appeared on screen.
3)  On Thumbnail menu, the following features are supported.
- Projector Control:    Have Easy/Advanced Menu on screen to control the projector, or change the input port to S-VIDEO.- Thumbnail display:   Display many stored images in USB storage at once. - Slide show: Switch images with set intervals.
- Display in full screen:   Display one still picture or moving picture in full screen. ( It is not in Thumbnail menu.)
USB STORAGE 
						

							
49

USB STORAGE
Displaying Thumbnail Menu (continued .)
The “PC-LESS Presentation” can be controlled via control panel on the projector 
or the remote control. 
Following button operations can be valid while Thumbnail menu is displayed.
ItemDescription
▲/▼/◄/► on Remote control /Control panelMove cursor
“ENTER” on Remote control“INPUT/ENTER” on Control panel
Works as ENTER function
-  Display selected image in full screen, when the cursor is pointed one of the image on Thumbnail Display in Thumbnail menu.
-  Select Thumbnail Menu item, when the cursor is at the menu in Thumbnail menu.
NOTE 2
•   Do  not  connect  any  apparatus  other  than  USB  storage  devices  and  other 
equipments for battery charge through USB. It causes malfunction.
•  Insert  only  one  memory  card  even  though  USB  card  reader  having  multiple 
slots  for  memory  card  is  used.  Pictures  in  multiple  memories  cannot  be  seen 
at the same time.
•  
The  OSD  message  “No  Media”  is  displayed,  if  there  is  no  memory  card  with 
USB card reader.
•   During  blinking  LED  on  USB  card  reader,  which  indicates  the  access  to  the 
reader, or displaying “Media loading…”, do not turn the projector into the power 
off/standby mode nor remove/insert USB cable and memory card.
•  Following message might appear when projector input port is changed to [USB 
STORAGE].
Thumbnail Menu
Thumbnail DisplayMenu
Displaying Thumbnail Menu (continued)
5.%6064
2,%10641.
6*7/$0#+.
5.+&5*19
!¹Ý
+0648#.U5612
/1&106+/
2.#;56#46
!¹Ý!¹Ý
!¹Ý!¹Ý!¹Ý
!¹Ý!¹Ý!¹Ý
!¹Ý!¹Ý!¹Ý
CDEFGHIJCDEFGHIJCDEFGHIJ
CDEFGHIJCDEFGHIJCDEFGHIJ
CDEFGHIJCDEFGHIJCDEFGHIJ
CDEFGHIJ CDEFGHIJCDEFGHIJ5%40((%6
+/#)#NN2CIG7R2CIG&QYP
+02765.%6/07
064 
						

							
50

USB STORAGE
Displaying Thumbnail Menu (continued)
MessageDescription
No MediaUSB  storage  is  not  inserted  into  USB  STORAGE  slot  on the projector.
Broken MediaThis  is  an  alarm  message  that  USB  storage  inserted  into USB STORAGE slot on the projector is broken.
Bad formatThis  is  an  alarm  message  that  USB  storage  inserted  into USB  STORAGE  slot  on  the  projector  has  a  noncompliant format.
Media loadingL o a d i n g   f i l e s   i n   t h e   U S B   s t o r a g e   i n s e r t e d   i n t o   U S B STORAGE slot on the projector. Please wait for a while.
ReadyPreparation  of  thumbnail  display  for  the  USB  storage inserted  into  USB  STORAGE  slot  on  the  projector  has been completed. Please wait for a while more.
•  Do not use this function other than private purposes. It might infringe copyright 
laws.
•  Back  up  all  of  the  data  in  the  memory  card,  in  case  any  data  are  lost  due  to 
unexpected  accident.   Any  liability  for  the  loss  by  mistake  or  malfunction  shall 
not be assumed.
•  Depends  on  USB  Storage  Devices, Thumbnail  display  might  disappears  once 
at the beginning of connection and comes again.
Controlling the projector
While Thumbnail menu is on screen, some buttons on the projector and remote 
control are assigned some designated functions to support the menu operation. 
If normal EASY or Advanced MENU on screen, or INPUT SELECT function is 
required, select PJ CONTROL item on the Thumbnail menu. 
Use ▲, ▼, ◄ and ► buttons to move a cursor to the PJ CONTROL item in 
Thumbnail menu.  Push ENTER button on the remote control or INPUT/ENTER 
button on the projector to decide the selected item. Following items can be 
controlled. 
PJ CONTROL items
ItemDescription
MENUDisplay EASY/Advanced MENU of the projector. Select [MENU] using ▲, ▼, ◄ and ► buttons, then push ENTER button on the remote control or INPUT/ENTER button on the projector.
INPUT SELECT
Change input port of the projector. Select [INPUT SELECT] using ▲, ▼, ◄ and ► buttons, then push ENTER button on the remote control or INPUT/ENTER button on the projector, so the input port will be changed from USB STORAGE to S-VIDEO.  Then, Thumbnail menu will be disappeared.