Hitachi Cp-X880w Liquid Crystal Projector Users Manual

17
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for
approximately 5 seconds. 
3Check that the STANDBY/ON indicator
stops blinking and lights to
solid orange.
Switch the power switch to
[O] (OFF).
4Confirm that the STANDBY/ON indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
STANDBY/ON indicator will go off.
TURNING OFF THE POWER
2Press the STANDBY/ON button again
(control panel or...

1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
2Use the lever switch  /  to adjust the
volume
Press the VOLUME...

19
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen to
aid you in adjusting the position.
2Use the , , , buttons to adjust the
position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB/BNC (RGB) input.
ADJUSTING THE...

The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly...

21
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
NOTE
CORRECTING KEYSTONE DISTORTIONS
1Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion. 
2Use the , buttons to select the
direction of distortion to correct ( / )
3Use the lever switch/ to correct
distortion
Press the KEYSTONE button again to close the...

The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signals state.
NOTE
•The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signals state.
•If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might...

23
•May not function properly with some input signals.
• This function takes about 10 seconds to display an image.
NOTES
ADJUSTING SCREEN WITH ONE-TOUCH
1Press the ONE TOUCH button
You can activate the following functions just by
pressing the ONE TOUCH button:
(1) Signal search:Cycle through input signals, displaying
the images of retrieved signals. If no signal is found,
returns to the signal that was selected before the search
was begun.
(2) Automatic adjustment:In RGB mode, automatically
adjust the...

24
SELECTING THE ASPECT RATIO
TEMPORARILY BLANKING THE SCREEN
1Press the ASPECT button
RGB, DVI, COMPONENT VIDEO
(HDTV signals : 1125i (1035i/1080i), 750p)
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO
(Non-HDTV signals : 525i, 525p,625i)
4:316:9
4:3 16:9 SMALL
1Press the BLANK button
The input signal screen is shut off, and a blank screen
appears. You can set the blank screen using the menu
(from the SCREEN menu, select BLANK). Press the BLANK
button again to remove the blank screen, and return to the
input...

25
USING THE MENU FUNCTIONS
1Press the MENU button
The menu display appears on the screen. The projector
has the following menus: MAIN, PICTURE-1, PICTURE-2,
INPUT, AUTO, SCREEN, and OPTION, WIRELESS. When
you select a menu name using the lever switch  /  , the
current settings of items that can be manipulated from that menu are displayed.
2Use the lever switch  /  to select a menu, then
press the or ENTER button
The display of the selected menu appears.
[ex. Adjusting SHARPNESS]
Use the lever switch  /...

26You can use the remote control as a simplified mouse or keyboard.
OPERATING THE PC SCREEN
CAUTIONCaution: Mistaken use of the mouse/keyboard control could damage your equipment.
• Only connect to a PC.
• Before connecting, read the manuals of the device you will connect.
• Do not unplug the connector cables while the computer is operating.
• It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.
track balls), using this remote control. In this case,...