Hitachi Cp-X809 Projector Users Manual

							51
OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY
(continued)
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
3.1 Registering the PIN Code3.1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button 
or the 
ENTER button to display the PIN LOCK 
on/off menu.
3.1-2   Use the ▲/▼ buttons on the PIN LOCK on/off 
menu to select TURN ON and the PIN BOX 
will be displayed. 
3.1-3    Input a 4 part PIN Code using the ▲/▼/◄/►, 
RGB and INPUT  buttons. 
The PIN CODE AGAIN BOX will appear. 
Reenter the same PIN Code. This will 
complete the PIN Code registration.
• If there is no key input for about 55 seconds while 
the PIN BOX or the PIN CODE AGAIN BOX is 
displayed, the menu will close. If necessary, repeat 
the process from 3.1-1.
Afterwards, anytime the projector is restarted after 
the power switch is turned off the PIN BOX will be 
displayed. Enter the registered PIN Code.
The projector can be used after entering the 
registered PIN Code. If an incorrect PIN Code is 
input, the PIN BOX will be displayed again.
If an incorrect PIN Code is input 3 times, the projector will turn of f. 
Afterwards the projector will turn off every time an incorrect PIN Code is 
input. The projector will also turn off if there is no key input for about 5 
minutes while the PIN BOX is displayed.
This function will activate only when the projector is started after the power 
switch was turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3.2-1   Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. 
Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be 
displayed.  
Enter the registered PIN Code to turn the PIN LOCK function off.
If an incorrect PASSWORD is input 3 times, the menu will close.
3.3 If you have forgotten your PIN Code
3.3-1   While the PIN BOX is displayed, press and 
hold the RESET  button for three seconds 
or press and hold the INPUT  button for 3 
seconds while pressing the ► button on the 
projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes while the Inquiring Code is 
displayed, the projector will turn off.
3.3-2   Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed.
(continued on next page) 
						

							52
OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY
(continued)
4. Using the Transition Detector FunctionWhile the Transition Detector function is ON, when power switch is started to 
supply to the projector, it might react as below.
• Transition Detector alarm shown below might appear on screen, if the 
projector has been moved or re-installed.
• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the  Transition 
Detector function is ON.
4.1 Turning On the Transition Detector Function4.1-1   Use the ▲/▼ buttons on the SECURITY menu to select Transition 
Detector and press the ► or the ENTER button to display the 
Transition Detector on/off menu. Select TURN ON and the current 
angle and mirror setting will be recorded.
• 
This feature may not function properly if the projector is 
not in a stable position when TURN ON is selected.
4.1-2  If this function is set to TURN ON when the 
vertical angle of the projector or mirror setting 
at which the projector is turned on is different 
than the previously recorded, the Transition 
Detector Alarm will be displayed and the 
projector will not display the input signal.
Set the Transition Detector off in the SECURITY menu to display the input signal.If the Transition Detector ALARM is displayed for about 5 minutes, the lamp will turn off. This function will activate only when the projector is started after the power 
switch was turned off.
4.2 Setting the Transition Detector PASSWORD4.2-1   Use the ▲/▼ buttons on the SECURITY menu to select Transition 
Detector and press the ► or the ENTER button to display the 
Transition Detector on/off menu.
4.2-2   Use the ▲/▼ buttons on the Transition 
Detector on/off menu to select TURN ON. 
The ENTER PASSWORD BOX (small) will be 
displayed.
4.2-3 
 Use the ▲/▼/◄/► buttons to enter a 
PASSWORD. Move the cursor to the right side of 
the ENTER PASSWORD BOX (small) and press 
the 
► button to display the PASSWORD AGAIN 
BOX, enter the same PASSWORD again.
4.2-4   Move the cursor to the right side of the 
PASSWORD AGAIN BOX and press the 
► button to display the PASSWORD for 
about 20 seconds, please make note of the 
PASSWORD during this time.
Pressing the 
ENTER button on the remote control or the INPUT  button on 
the projector will return to the Transition Detector on/off menu.
• Please do not forget your Transition Detector PASSWORD.
4.3 Setting the Transition Detector off4.3-1  Follow the procedure in 4.1-1 to display the Transition Detector on/off menu.4.3-2   Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the 
Transition Detector on/off menu.
If an incorrect PASSWORD is input, the menu will close. If necessary, repeat 
the process from 4.3-1.
(continued on next page)
ENTER PASSWORD BOX  (small) 
						

							53
OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY
(continued) 4.4 If you have forgotten your PASSWORD
4.4-1  Follow the procedure in 4.1-1 to display the Transition Detector on/off menu.4.4-2  Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10 digit Inquiring 
Code will be displayed inside the BOX.
4.4-3  
Contact your dealer with the 10 digit Inquiring 
Code. Your PASSWORD will be sent after your 
user registration information is confirmed.
5. Using the MY TEXT PASSWORD functionThis item allows you to display your own message (MY TEXT) on the START 
UP screen and INPUT-INFORMATION-. It can be protected by a password to 
prevent it from being overwritten.
5.1 Writing the MY TEXT(1)  Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT WRITING menu and 
press the ► button. The MY TEXT WRITING 
dialog will be displayed.
(2) 
 The current MY TEXT will be displayed on the first 3 lines. If not yet written, the 
lines will be blank. 
Use the 
▲/▼/◄/► buttons and the ENTER  or INPUT button to select and enter 
characters. The RESET  button can be used to erase 1 character at a time. Also if 
you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER 
or INPUT  button, 1 character or all characters will be erased. The MY TEXT can 
be input up to 24 characters on each line.
(3)   
To change an already inserted character, press 
the ▲/▼ button to move the cursor to one of the 
first 3 lines, and use the ◄/► buttons to move 
the cursor on the character to be changed.
After pressing the 
ENTER or INPUT  button, the 
character is selected. Then, follow the same 
procedure as described at the item (2) above.
(4)    To finish entering text, move the cursor to the 
SAVE on screen and press the 
ENTER or INPUT  
button. To revert to the previous MY TEXT 
without saving changes, move the cursor to the 
CANCEL on screen and press the 
ENTER or INPUT  button.• The MY TEXT WRITING function is available only when the MY TEXT 
PASSWORD function is set to TURN OFF.
5.2 Displaying the MY TEXT(1)   Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT DISPLAY menu and 
press the ► button to display the MY TEXT 
DISPLAY on/off menu.
(2)   Use the ▲/▼ buttons on the MY TEXT DISPLAY 
on/off menu to select on or off.
TURN ON 
ó TURN OFFWhen it is set TURN ON, the MY TEXT will be 
displayed on the START UP screen and the INPUT-
INFORMATION- when the INFORMATION on the 
SERVICE menu is chosen.
• This function is available only when the MY TEXT 
PASSWORD function is set to the TURN OFF.
ENTER PASSWORD BOX 
(large)
(continued on next page) 
						

							54
OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY
(continued) 5.3 Turning on the MY TEXT PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten.5.3-1 
 
Turning on the MY TEXT PASSWORD function
(1)   Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT PASSWORD menu and 
press the ► button to display the MY TEXT 
PASSWORD on/off menu.
5.3-2   Setting the MY TEXT PASSWORD
(1)   Display the MY TEXT PASSWORD on/off menu 
using the procedure in 5.3-1
(2)   Use the ▲/▼ buttons on the MY TEXT 
PASSWORD menu to select TURN ON. The 
ENTER PASSWORD BOX (small) will be 
displayed.
(3)   Use the ▲/▼/◄/► buttons to enter the 
PASSWORD. Move the cursor to the right side of 
the ENTER PASSWORD BOX (small) and press 
the ► button to display the PASSWORD AGAIN 
BOX, and then enter the same PASSWORD 
again.
(4)   Move the cursor to the right side of the 
PASSWORD AGAIN BOX and press ► button to 
display the PASSWORD for about 20 seconds, 
then please make note of the PASSWORD 
during this time.
Pressing the 
ENTER button on the remote control 
or INPUT  button on the projector will return to the 
MY TEXT PASSWORD on/off menu. When the 
PASSWORD is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
5.3-3    Turning the MY TEXT PASSWORD off
(1)   Follow the procedure in 5.3-1 to display the MY 
TEXT PASSWORD on/off menu.
(2)   Select TURN OFF to display the ENTER 
PASSWORD BOX (large). Enter the registered 
PASSWORD and the screen will return to the 
MY TEXT PASSWORD on/off menu. 
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 5.3-3(1)
5.3.4 If you have forgotten your PASSWORD.
(1)   Follow the procedure in 5.3-1 to display the MY TEXT PASSWORD on/
off menu.
(2)   Select TURN OFF to display the ENTER PASSWORD BOX (large). The 
10 digit inquiring code will be displayed inside the box. 
(3)   Contact your dealer with the 10 digit inquiring code. Your PASSWORD 
will be sent after your user registration information is confirmed.
ENTER PASSWORD BOX 
(small)
ENTER PASSWORD BOX  (large) 
						

							55
MIU menu
The MIU (Multi Information processing Unit) is a function to 
support the Network features and PC-LESS Presentation.
Consult with your network administrator before connecting to 
an existing access point on your network. Incorrect network 
settings on this projector may cause trouble on the network.
Select “MIU” from the main menu to access the following 
functions.
Select an item using the ▲/▼ cursor buttons on the projector or remote control, and 
press the ► cursor button on the projector or remote control, or 
ENTER button on the 
remote control to execute the item. Then perform it according to the following table.
See the User’s Manual - Network Guide for details of MIU operation.
Item Description
LIVE MODE Selecting this item sets the projector onto the “Live Mode”. 
On the “Live Mode”, the projector displays the images from the PC 
via Network, supported by “Live Viewer 3” software.
 (Live Mode of 
the User’s Manual - Network Guide
 5)
LIVE MODE  SETTING Selecting this item displays the LIVE MODE 
 
SETTING menu.
Use the ▲/▼ buttons to select an item, and  
the ► or 
ENTER button to perform the item.
QUIT 
PRESENTER  MODE
The Presenter Mode that is set in the "Live Viewer 3" software 
installed into your PC can be turned to off.
A message, QUIT PRESENTER MODE, will 
be displayed in about 3 seconds when the 
function is performed. The function is available only when the 
Presenter Mode is set to on in the the "Live Viewer 3" software. 
The current setting of the Presenter Mode is shown in the menu.
• The Presenter mode is a function that allows the projector 
to display an image sent by 1 PC only, even though the 
MIU feature on this projector support Multi PC mode.
• If the projector is required to display an image sent by 
other PC, execute the QUIT PRESENTER MODE function.
• See the User’s Manual – Network Guide for details. 
(continued on next page)
MIU menu
• The factory default setting for DHCP is TURN OFF. If your network 
has DHCP enabled, and needs to set IP ADDRESS, SUBNET MASK and 
DEFAULT GATEWAY automatically, please set DHCP to TURN ON (
58).
• If you are not utilizing SNTP (
Date/Time Settings of the User’s Manual 
- Network Guide ), then you must set the DATE AND TIME (
59) during the 
initial installation. NOTE 
						

							56
MIU menu
MIU menu (continued)
(continued on next page)
ItemDescription
LIVE MODE  SETTING
(continued) MULTI 
PC 
MODE
The projector supports the Single PC mode  
that displays an image on full screen sent by  
1 PC, and the Multi PC mode that divides the  
screen into 4 zone and displays images in  
each zone sent by up to 4 PCs. The MULTI  
PC MODE function switches these modes.
SINGLE
Use the ▲/▼ buttons to select an item, and the ENTER 
or INPUT  button to perform the item. The mode will be 
switched from the Multi PC mode to the Single PC mode 
and the quarter screen identified in the menu will be 
displayed on full screen.
MULTI
Use the 
ENTER or INPUT  button to perform the item.  
The mode will be switched to the Multi PC mode and the 
screen will be divided to 4 zones.
• If the Presenter Mode is set to on in the PC whose 
image is currently displayed on screen, a message, 
QUIT PRESENTER MODE, will be displayed in about 3 
seconds when the function is performed.
• The function is available when there is any PC 
connected to the projector in the Multi PC mode set in 
the "Live Viewer 3" software.
DISPLAY  USER 
NAME
Selecting this item displays the Display User Name 
defined in the "Live Viewer 3" software in the PC whose 
image is on screen.
SINGLE PC mode
The Display User Name will be 
shown in the DISPLAY USER NAME box.
Examples Display User name         Shown in the DISPLAY USER 
NAME box
     PC_NAME0001              PC_NAME0001
   (remained as default)            Unnamed
   (blank space)                   
   (prohibited showing)           (Anonymous)
If there is no PC in the Single PC 
mode connected to the projector, 
the DISPLAY USER NAME box is shown as right.
MULTI PC mode
The Display User Names will be 
shown in the DISPLAY USER 
NAME box.
• See the 
User’s Manual – Network Guide for details 
of the Display User Name setting. 
						

							57
MIU menu
MIU menu (continued)
ItemDescription
PC-LESS 
PRESENTATION Selecting this item displays the PC-LESS PRESENTATION menu.
Using the menu is able to make the projector display the images 
stored in an SD memory card or a USB memory, and realizes a 
presentation without a PC.
Use the ▲/▼/◄/► buttons to select an item, and  
the ► or ENTER button to perform the item.
• While displaying the image, to press the   MENU button displays the PC-LESS  
PRESENTATION menu.
THUMBNAIL Use the ▲/▼/◄/► 
buttons to select an 
image, and press the 
ENTER or INPUT
 button 
to display the image.
SLIDE SHOW Slide show will start when you press the 
ENTER or ► button.
DIRECTORY
Use the ▲/▼ buttons 
to select an image or 
a folder, and press the 
ENTER or INPUT button 
to display the image or 
turn into the THUMBNAIL.
To open or close the folder, press the ►/◄ 
buttons.
DISPLAY SIZE Use the ▲/▼ buttons to 
set the display size.
KEY CONFIG. Use the ▲/▼ buttons to 
select key configuration 
from the 2 patterns.
REMOVE MEDIA Use the ▲/▼ buttons to 
select a remove mode, 
and then the 
ENTER or 
► button is pressed so 
the menu to excuse will 
appear.
• Also these items can be set with Web Remote Control (Refer 
to Network Guide) except DISPLAY SIZE, KEY CONFIG. and 
REMOVE MEDIA. 
(continued on next page) 
						

							58
MIU menu
MIU menu (continued)
ItemDescription
SETUP Selecting this item displays the MIU SETUP menu.
Use the ▲/▼ buttons to select an item, and the ► 
or 
ENTER button on the remote control to perform 
the item.
DHCP 
(Dynamic Host  Configuration  Protocol) Use the ▲/▼ buttons to turn DHCP on/off.
ON  ó OFF
Select OFF when the network does  
not have DHCP enabled.
• When the “DHCP” setting changes to “ON”, 
it takes a little time to obtain IP address from 
DHCP server.
• Auto IP function will be assigned an IP 
address if the projector could not obtain an IP 
address from server even if DHCP is “ON”.
IP ADDRESS Use the ▲/▼
/◄/► 
buttons to enter the IP 
ADDRESS. This function 
can only be used when 
DHCP is set to OFF.
• 
The IP ADDRESS is the number that identifies this 
projector on the network. You cannot have two devices 
with the same IP ADDRESS on the same network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET MASK Use the ▲/▼
/◄/► 
buttons to enter the same 
SUBNET MASK used by 
your PC. This function 
can only be used when 
DHCP is set to OFF.
•  The SUBNET MASK “0.0.0.0” is prohibited.
DEFAULT 
GATEWAY Use the ▲/▼
/◄/►  
buttons to enter the 
DEFAULT GATEWAY 
(a node on a computer 
network that serves as an 
access point to another 
network) address.
This function can only be used when DHCP is 
set to OFF.
DNS SERVER
Use the ▲/▼/◄/►
 buttons to input the DNS 
server address. The DNS 
server is a system to control 
domain names and IP addresses on the Network.
(continued on next page) 
						

							59
MIU menu
MIU menu (continued)
ItemDescription
SETUP
(continued) TIME 
DIFFERENCE Use the ▲/▼ buttons 
to enter the TIME 
DIFFERENCE. 
Set the same TIME 
DIFFERENCE as the 
one set on your PC. 
If unsure, consult 
your IT manager. 
Use the ◄ button to return to the menu after 
setting the TIME DIFFERENCE.
DATE AND TIME Use the ▲/▼
/◄/► 
buttons to enter the Year 
(last two digits), Month, 
Date, Hour and Minute.
• The projector will override this setting and 
retrieve DATE AND TIME information from the 
Time server when SNTP is enabled.   
(
Date/T ime Settings of the User’s Manual 
- Network Guide)
MODE Use the ▲/▼ buttons to 
select the mode of the 
network communication 
system. Select it according 
to the setting of your PC.
ADHOC  ó INFRASTRUCTURE
CH Use the ▲/▼ buttons to 
select the channel of the 
wireless LAN while using 
it. Select it according to the 
setting of your PC.
The channels 1 to 11 are available.
• The available channels would be various 
depending on a country. In addition, wireless 
network card might be required due to the standard.
ENCRYPTION Use the ▲/▼ buttons 
to select the encryption 
method to be used.
WPA2-PSK(AES) 
ó WPA-PSK(AES) 
ó WPA-PSK(TKIP) 
 
                OFF  ó WEP 64bit 
ó WEP 128bit
 
(continued on next page) 
						

							60
MIU menu
MIU menu (continued)
ItemDescription
SETUP
(continued) SSIDUse the ▲/▼ 
buttons to select 
the SSID 
to display the 
SSID menu.
DEFAULT
Pressing the ► or ENTER button when one of 
the  DEFAULT (#1~#4) is selected. 
CUSTOM
Press the ► or 
ENTER button when the # 5 
CUSTOM is selected. The SSID #5 CUSTOM 
menu will be appeared.
(1)    The current SSID will be displayed on the  
first line. If not yet written, the line will be 
blank. Use the ▲/▼/◄/► buttons and the 
ENTER or INPUT  button to select and enter 
characters. The RESET  button can be used 
to erase 1 character at a time. Also if you 
move the cursor to DELETE or ALL CLEAR 
on screen and push the 
ENTER or INPUT  
button, 1 character or all characters will be 
erased. The SSID can be input up to 32 
characters. 
(2)  
To change an 
already inserted 
character, 
press the ▲/▼ 
button to move 
the cursor to 
one of the first 
2 lines, and 
use the ◄/► 
buttons to move 
the cursor on 
the character 
to be changed. 
After pressing 
the 
ENTER or INPUT button, 
the character is 
selected.  Then, 
follow the same 
procedure as 
described at the 
item (1) above.
(3)    To finish entering text, move the cursor to 
the SAVE on screen and press the ENTER 
or INPUT button. To revert to the previous 
SSID without saving changes, move the 
cursor to the CANCEL on screen and press 
the 
ENTER or INPUT button.
(continued on next page)