Hitachi Cp-X505 Projector Users Manual



Setting up
NOTE  • Be sure to read the manuals for devices before connecting them to\
 the 
projector, and make sure that all the devices are suitable to be connected with t\
his 
product. Before connecting to a PC, check the signal level, the signal t\
iming, and the 
resolution.
-  Do not connect LAN port to any network that might have the excessive vol\
tage.
- 
 Some signal may need an adapter to input this projector.
- 
 Some PCs have multiple screen display modes that may include some...



Setting up
Connecting power supply
. Connect the connector of the power cord to the AC inlet of the projector.
. Firmly plug the power cord's plug into the outlet. 
WARNING  ►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated...

3

Remote control
Putting batteries
Please load the batteries before using the remote control. If the remote\
 control starts to 
malfunction, replace the batteries. If you will not use the remote contr\
ol for an extended 
period, remove the batteries from the remote control and store them in a\
 safe place.
. Slide back and remove the 
battery cover in the direction 
of the arrow.
. Align and insert the two AA 
batteries according to their 
plus and minus   terminals as indicated in the...

4

Changing the frequency of  remote control signal
The accessory remote control has the choice of the 
mode 
  or the mode   , in the frequency of its signal. 
If  the  remote  control  does  not  function  properly, attempt to change the signal frequency.Please  remember  that  the  “REMOTE  FREQ.”  in SERVICE  item  of  OPTION  menu (46)  of  the 
projector to be controlled should be set to the same mode as the remote control.To  set  the  mode  of  the  remote  control,  slide  the...

5

Using as a wired remote control
The accessory remote control works as a wired remote control, when the wired control port at the bottom of the remote control connects with the REMOTE CONTROL port on the back of the projector via an audio cable with 3.5 diameter stereo mini plugs. When the remote control signal is hard to reach surely to the projector in the environment, this function is effective.
Remote control
NOTE  • To connect the remote control with the projector, use an audio cable with...

6

Power on/off
Turning on the power
. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.
. Remove the lens cover, and set the power switch to the ON position.  The power indicator will light up in steady orange (63). Then wait several seconds because the buttons may not function for these several seconds. 
(1) When AUTO ON in OPTION menu is set to TURN ON (42) :The lamp will only be automatically turned on when the Power switch is turned on...

7

Operating
Operating
Adjusting the volume
. Press the VOLUME button on the remote control. 
A dialog will appear on the screen to aid you in adjusting the volume.
. Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the 
VOLUME button again. Even if you do not do anything, the 
dialog will automatically disappear after a few seconds.
● When no audio port is selected for current picture input port, the volume 
adjustment is disable....

8

Operating
Searching an input signal
. Press the SEARCH button on the remote control.
The projector will start to check its input ports in order to 
find any input signals.
When an input is found, the projector will stop searching and display th\
e image. 
If no signal is found, the projector will return to the state selected b\
efore the 
operation.
RGB     RGB     M  -D  COMPONENT (Y, CB/RB, CR/BR)  S-VIDEO  VIDEO 
   
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO...

9

Adjusting the zoom and focus
. Use the zoom ring to adjust the screen size.  
. Use the focus ring to focus the picture.
Operating
Focus ringZoom ring
Adjusting the lens shift
. Use the vertical lens shift dial to shift 
the picture upward or downward.  
. Use the horizontal lens shift dial to 
shift the picture left or right.
Using the automatic adjustment feature
. Press the AUTO button on the remote control.  
 For an RGB signal 
The vertical position, the horizontal...

0

Adjusting the position
. Press the POSITION button on the remote control. 
The “POSITION” indication will appear on the screen.
. Use the cursor buttons ▲/▼/◄/► to adjust the picture 
position.
When you want to reset the operation, press the RESET button on the remote 
control during the operation.
To complete this operation, press the POSITION button again. Even if you \
do 
not do anything, the dialog will automatically disappear after a few sec\
onds.
● When this function is...