Hitachi Cp-X4021n Projector Users Manual

							31
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then 
perform it according to the following table.
Item Description
ASPECTUsing the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE menu (
36).
AUTO KEYSTONE Using the ► button executes the auto keystone function.See the AUTO KEYSTONE item in SETUP menu (43).
 KEYSTONEUsing the ◄/► buttons corrects the vertical keystone distortion.
See the  KEYSTONE item in SETUP menu (43).
 KEYSTONEUsing the ◄/► buttons corrects the horizontal keystone distortion.
See the  KEYSTONE in SETUP menu (44).
PERFECT FITPressing the ► button displays the KEYSTONE_PERFECT FIT 
dialog. See the PERFECT FIT item in SETUP menu (
44).
PICTURE MODEUsing the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP 
settings. Choose a suitable mode according to the projected source.
     NORMAL 
 CINEMA 
 DYNAMIC 
 BOARD(BLACK)
          DAYTIME 
 WHITEBOARD 
 BOARD(GREEN)
GAMMA COLOR TEMP
NORMAL 1 DEFAULT 2 MID
CINEMA 2 DEFAULT 3 LOW
DYNAMIC 3 DEFAULT 1 HIGH
BOARD(BLACK) 4 DEFAULT 4 Hi-BRIGHT-1
BOARD(GREEN) 4 DEFAULT 5 Hi-BRIGHT-2
WHITEBOARD 5 DEFAULT 2 MID
DAYTIME 6 DEFAULT 6 Hi-BRIGHT-3
• When the combination of GAMMA and COLOR TEMP differs 
from pre-assigned modes above, the display on the menu for the 
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and 
COLOR TEMP (
33, 34) items in PICTURE menu.
• Lines or other noise might appear on the screen when this function 
is operated, but it is not a malfunction.
(continued on next page) 
						

							32
EASY MENU
Item Description
ECO MODEUsing the ◄/► buttons turns off/on the Eco mode.
See the ECO MODE item in SETUP menu (
44).
MIRRORUsing the ◄/► buttons switches the mode for mirror status.
See the MIRROR item in SETUP menu (
44).
RESETPerforming this item resets all of the EASY MENU items except the 
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting the OK using the ► 
button performs resetting.
FILTER TIMEThe usage time of the air filter is shown in the menu.
Performing this item resets the filter time which counts usage time 
of the air filter.
A dialog is displayed for confirmation. Selecting the OK using the ► 
button performs resetting. 
See the FILTER TIME item in OPTION menu (
56).
LANGUAGEUsing the ◄/► buttons changes the display language. 
See the LANGUAGE item in SCREEN menu (
48).
ADVANCED MENU
Press the ► or ENTER button to use the menu of PICTURE, 
IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or 
SECURITY.
EXITPress the ◄ or ENTER button to finish the OSD menu. 
						

							33
PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table 
below can be performed. 
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the 
item. Then perform it according to the following table.
Item Description
BRIGHTNESSUsing the 
◄/► buttons adjusts the brightness.
Dark 
 Light
CONTRASTUsing the 
◄/► buttons adjusts the contrast.
Weak 
 Strong
GAMMAUsing the ▲/▼ buttons switches the gamma mode.
To adjust CUSTOM
Selecting a mode whose name includes CUSTOM and then 
pressing the ► button or the ENTER button displays  
a dialog to aid you in adjusting the mode. 
This function is useful when you want to  
change the brightness of particular tones.
Choose an item using the ◄/► buttons,  
and  adjust the level using the ▲/▼ buttons.
You can display a test pattern for checking the effect of your 
adjustment by pressing the ENTER button. 
Each time you press the ENTER button, the  
pattern changes as below.
  No pattern 
 Gray scale of 9 steps 
     Ramp 
 Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the test 
pattern (Gray scale of 9 steps) except the darkest in the left end. If you 
want to adjust the 2nd tone from left end on the test pattern, use the 
equalizing adjustment bar “1”. The darkest tone at the left end of the 
test pattern cannot be controlled with any of equalizing adjustment bar.
• Lines or other noise might appear on the 
screen when this function is operated, but it 
is not a malfunction.
(continued on next page)
  
1 DEFAULT  1 CUSTOM  2 DEFAULT  2 CUSTOM  3 DEFAULT
6 CUSTOM                                                                                          3 CUSTOM
6 DEFAULT 
 5 CUSTOM  5 DEFAULT  4 CUSTOM  4 DEFAULT 
						

							34
PICTURE menu
(continued on next page)
Item Description
COLOR TEMPUsing the ▲/▼ buttons switches the color temperature mode.
To adjust CUSTOM
Selecting a mode whose name includes 
CUSTOM and then pressing the ► button 
or the ENTER button displays a dialog 
to aid you in adjusting the OFFSET and 
GAIN of the selected mode.
OFFSET adjustments change the color intensity on the whole tones 
of the test pattern.
GAIN adjustments mainly affect color intensity on the brighter tones 
of the test pattern.
Choose an item using the ◄/► buttons, and adjust the level using 
the ▲/▼ buttons. 
You can display a test pattern for checking the effect of your 
adjustment by pressing the ENTER button.  
Each time you press the ENTER button, the pattern changes as below.
No pattern 
 Gray scale of 9 steps  
     
 Ramp 
 Gray scale of 15 steps
• Lines or other noise might appear on the screen 
when this function is operated, but it is not a 
malfunction.
COLORUsing the ◄/► buttons adjusts the strength of whole color.
Weak 
 Strong
• This item can be selected only for a video, s-video and component 
video signal. 
• 
For an HDMI signal, this item can also be selected if either (1) or (2) applies. 
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)  HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals.
TINTUsing the ◄/► buttons adjusts the tint.
Reddish 
 Greenish
• This item can be selected only for a video, s-video and component 
video signal.
• 
For an HDMI signal, this item can also be selected if either (1) or (2) applies. 
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)  HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals.
1 HIGH  1 CUSTOM  2 MID  2 CUSTOM 
3 LOW
5 CUSTOM
5 Hi-BRIGHT-24 CUSTOM4 Hi-BRIGHT-1 6 CUSTOM
 

  
6 Hi-BRIGHT-3

3 CUSTOM 
						

							35
PICTURE menu
Item Description
SHARPNESSUsing the ◄/► buttons adjusts the sharpness.
Weak 
 Strong
• There may be some noise and/or the screen may flicker for a 
moment when an adjustment is made. This is not a malfunction.
ACTIVE IRIS
Using the ▲/▼ cursor buttons changes the active iris control mode.
PRESENTATION  
  THEATER  
  OFF
              
PRESENTATION :  The active iris displays the best presentation 
image for both bright and dark scenes.
THEATER :  The active iris displays the best theater image for 
both bright and dark scenes.
OFF :  The active iris is always open.
• The screen may flicker when the PRESENTATION or THEATER 
modes are selected. If this occurs select OFF.
MY MEMORY
This projector has 4 memories for adjustment data (for all the items 
of the PICTURE menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or 
ENTER button performs each function.
SAVE-1 
 SAVE-2 
 SAVE-3 
 SAVE-4
LOAD-4 
LOAD-3 
 LOAD-2 
 LOAD-1
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into 
the memory linked in the number included in the function’s name. 
• Remember that the current data being stored of a memory will be 
lost by saving new data into the memory.
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked 
in the number included in the function’s name, and adjusts the 
picture automatically depending on the data. 
• The LOAD functions whose linked memory has no data are 
skipped.
• Remember that the current adjusted condition will be lost by 
loading data. If you want to keep the current adjustment, please 
save it before performing a LOAD function.
• There may be some noise and the screen may flicker for a 
moment when loading data. This is not malfunction.
• You can perform the LOAD function using MY BUTTON. Please 
see MY BUTTON item in OPTION menu (
57). 
						

							36
IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
Item Description
ASPECTUsing the ▲/▼ buttons switches the mode for aspect ratio. 
For a computer signal
CP-X4021N, CP-X5021N: NORMAL 
 4:3 
 16:9 
 16:10 
                                               
 
CP-WX4021N: NORMAL 
 4:3 
 16:9 
 16:10 
 NATIVE 
                              
For an HDMI signal
CP-X4021N, CP-X5021N: NORMAL 
 4:3 
 16:9 
 16:10 
 14:9 
                                                 
CP-WX4021N: NORMAL 
 4:3 
 16:9 
 16:10 
 14:9 
 NATIVE 
                         
For a video signal, s-video signal or component video signal
CP-X4021, CP-X5021: 4:3 
 16:9 
 14:9 
                                      
CP-WX4021: 4:3 
 16:9 
 16:10 
 14:9 
 NATIVE
                           
For an input signal from the LAN, USB TYPE A or USB TYPE B 
port, or if there is no signal
CP-X4021N, CP-X5021N: 4:3 (fixed) 
CP-WX4021N: 16:10 (fixed)
• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCANUsing the ◄/► buttons adjusts the over-scan ratio.
Small (It magnifies picture) 
 Large (It reduces picture)
• This item can be selected only for a video, s-video and component 
video signal.
•
 For an HDMI signal, this item can also be selected if either (1) or (2) 
applies. 
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)  HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals.
(continued on next page) 
						

							37
IMAGE menu
Item Description
V POSITIONUsing the ◄/► buttons adjusts the vertical position.
Down 
 Up
• Over-adjusting the vertical position may cause noise to appear on 
the screen. If this occurs, please reset the vertical position to the 
default setting. Pressing the RESET button when the V POSITION 
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal or an s-video 
signal, the range of this adjustment depends on OVER SCAN (
36) 
setting. It is not possible to adjust when OVER SCAN is set to 10.
•
 This function is unavailable for a signal from the LAN, USB TYPE A, 
USB TYPE B or HDMI port.
H POSITIONUsing the ◄/► buttons adjusts the horizontal position.
Right 
 Left 
• 
Over-adjusting the horizontal position may cause noise to appear on 
the screen. If this occurs, please reset the horizontal position to the 
default setting. Pressing the RESET button when the H POSITION is 
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal or an s-video 
signal, the range of this adjustment depends on OVER SCAN (
36) 
setting. It is not possible to adjust when OVER SCAN is set to 10.
•
 This function is unavailable for a signal from the LAN, USB TYPE A, 
USB TYPE B or HDMI por
t.
(continued on next page) 
						

							38
IMAGE menu
Item Description
H PHASE
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right 
 Left
• This item can be selected only for a computer signal or a 
component video signal. This function is unavailable for a signal 
from the LAN, USB TYPE A, USB TYPE B or HDMI port.
H SIZEUsing the ◄/► buttons adjusts the horizontal size.
Small 
 Large
• This item can be selected only for a computer signal. This function 
is unavailable for a signal from the LAN, USB TYPE A, USB TYPE 
B or HDMI port.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the RESET button on the remote control during this 
operation.
• Images might appear degraded when this function is operated, but 
it is not a malfunction.
AUTO ADJUST 
EXECUTESelecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted.  
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
menu (
40). The vertical position and horizontal position will be 
automatically set to the default.
For a component video signal
The vertical position and horizontal position will be automatically 
set to the default. The horizontal phase will be automatically 
adjusted.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
• When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black 
frame may be displayed on the edge of the screen, depending on 
the PC model. 
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION menu (
59). 
						

							39
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
Item Description
PROGRESSIVEUsing the ▲/▼ buttons switches the progress mode.
TV 
 FILM 
 OFF
  
• This function works only for a video signal, s-video signal, component 
video signal (of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI 
signal (of 480i@60 or 576i@50 or 1080i@50/60)
.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select OFF, even 
though the screen image may lose sharpness.
VIDEO NRUsing the ▲/▼ buttons switches the noise reduction mode.
HIGH 
 MID 
 LOW
   
• This function works only for a video signal, s-video signal, 
component video signal (of 480i@60 or 576i@50 or 1080i@50/60) 
and an HDMI signal (of 480i@60 or 576i@50 or 1080i@50/60). 
COLOR SPACEUsing the ▲/▼ buttons switches the mode for color space.
AUTO 
 RGB 
 SMPTE240 
 REC709 
 REC601
      
• This item can be selected only for a computer signal (except for 
signals from the LAN, USB TYPE A and USB TYPE B ports)
 or a 
component video signal (except SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
COMPONENTUsing the ▲/▼ buttons switches the function of the COMPONENT 
ports.
COMPONENT 
 SCART RGB
When the SCART RGB is selected, the COMPONENT (Y, Cb/
Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. 
A SCART adapter or SCART cable is required for a SCART RGB 
input to the projector. For details, contact your dealer.
(continued on next page) 
						

							40
INPUT menu
(continued on next page)
Item Description
VIDEO FORMATThe video format for S-VIDEO port and VIDEO port can be set.
(1)  Use the ▲/▼ buttons to 
select the input port.
(2)  Using the ◄/► buttons 
switches the mode for video 
format.
AUTO  
  NTSC  
  PAL  
  SECAM
      N-PAL 
 M-PAL 
 NTSC4.43 
• This item is performed only for a video signal from the VIDEO port 
or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode according to the input signal.
HDMI FORMATUsing the ▲/▼ cursor buttons switches
 the video format for an 
input from the HDMI port.
AUTO  
  VIDEO  
  COMPUTER
Feature
AUTO automatically sets the optimum mode.
VIDEO sets the suitable mode for DVD signals.
COMPUTER sets the suitable mode for computer signals.
•
 When the COMPUTER is selected, the functions COLOR 
(PICTURE menu), TINT (PICTURE menu) and OVER SCAN 
(IMAGE menu) are unavailable.
HDMI RANGEUsing the ▲/▼ cursor buttons changes the digital range for input 
from the HDMI port.
AUTO  
  NORMAL  
  ENHANCED
Feature
AUTO automatically sets the optimum mode.
NORMAL s
ets the suitable mode for DVD signals. (16-235)
ENHANCED
sets the suitable mode for computer signals. (0-255)
• If the contrast of the screen image is too strong or too weak, try 
finding a more suitable mode.