Hitachi Cp-X308 Projector Users Manual

							
5

OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.• Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON.
4.1 Turning On the Transition Detector Function
4.1-1  U s e   t h e   ▲ / ▼   b u t t o n s   o n   t h e   S E C U R I T Y menu to select TRANSITION DETECTOR and press  the  ►  or  the  ENTER  button  to  display the  TRANSITION  DETECTOR  on/off  menu. Select TURN ON and the current angle and mirror setting will be recorded.• This feature may not function properly if the projector is not in a stable position when TURN ON is selected.
4.1-2   If  this  function  is  set  to  TURN  ON  when 
the  vertical  angle  of  the  projector  or  mirror setting  at  which  the  projector  is  turned  on is  different  than  the  previously  recorded  the Transition  Detector  alarm  will  be  displayed and  the  projector  will  not  display  the  input signal.
Set the Transition Detector off in the SECURITY menu to display the input signal.If the Transition Detector alarm is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after turning off the AC power.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or the ENTER button to display the TRANSITION DETECTOR on/off menu.
4.2-2   Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select TURN ON. The ENTER PASSWORD box (small) will be displayed.
4.2-3   Use the ▲/▼/◄/► buttons to enter a 
PASSWORD. Move the cursor to the right side of the ENTER PASSWORD box (small) and press the ► button to display the PASSWORD AGAIN box, enter the same PASSWORD again.
(continued on next page) 
						

							
5

OPTION menu
OPTION menu (continued)
ItemDescription
SECURITY(continued)
4.2-4  Move  the  cursor  to  the  right  side  of  the PA S S W O R D   A G A I N   b o x   a n d   p r e s s   t h e ►  button  to  display  the  PASSWORD  for about  20  seconds,  please  make  note  of  the PASSWORD during this time.Pressing the ENTER button will return to the TRANSITION DETECTOR on/off menu.• Please do not forget your Transition Detector PASSWORD.
4.3 Setting the Transition Detector off
4.3-1  Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.
4.3-2   Select TURN OFF to display the ENTER PASSWORD box (large). 
Enter the registered PASSWORD and the screen will return to the TRANSITION DETECTOR on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1.
4.4 If you have forgotten your PASSWORD
4.4-1  Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.
4.4-2   Select  TURN  OFF  to  display  the  ENTER 
PA S S W O R D   b o x   ( l a r g e ) .   T h e   1 0 - d i g i t Inquiring  Code  will  be  displayed  inside  the box.
4.4-3   Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed. 
						

							
53

The MIU (Multi Information processing Unit) is a function to 
support the Network features and PC-LESS Presentation.
Remember that incorrect network settings on this projector 
may cause trouble on the network. Be sure to consult with 
your network administrator before connecting to an existing 
access point on your network.
Select “MIU” from the main menu to access the following 
functions. 
Select an item using the ▲/▼ cursor buttons on the projector or remote control, 
and press the ► cursor button on the projector or remote control, or ENTER 
button on the remote control to execute the item. Then perform it according to the 
following table.
See the User’s Manual - Network Guide for details of MIU operation.
MIU menu
(continued on next page)
MIU menu
• The factory default setting for DHCP is OFF. If your network has 
DHCP enabled, and needs to set IP ADDRESS, SUBNET MASK and DEFAULT 
GATEWAY automatically, please set DHCP to ON. ( Network Settings of 
the User’s Manual - Network Guide)
• If you are not utilizing SNTP ( Date/Time Settings of the User’s Manual 
- Network Guide), then you must set the DATE AND TIME (57) during the 
initial installation.
NOTE
ItemDescription
LIVE MODE
Selecting this item sets the projector onto the “Live Mode”. On the “Live Mode”, the projector displays the images from the PC via Network, supported by “MIU Live Viewer”. ( Live Mode of the User’s Manual - Network Guide)In the Live Mode, the message “Waiting for connection” will be displayed until the “MIU Live Viewer” start to send computer screen image.
LIVE MODE SETTING
Selecting this item displays the LIVE MODE SETTING menu.Use the ▲/▼ buttons to select an item, and the ► or ENTER button to perform the item. 
						

							
54

MIU menu
MIU menu (continued)
ItemDescription
LIVE MODE SETTING(continued)
QUIT PRESENTER MODE
The Presenter Mode that is set in the Live Viewer 3 software installed into your PC can be turned to off.A message, QUIT PRESENTER MODE, will be displayed in about 3 seconds when the function is performed. The function is available only when the Presenter Mode is set to on in the Live Viewer 3 software. The current setting of the Presenter Mode is shown in the menu.• The Presenter mode is a function that allows the projector to display an image sent by 1 PC only, even though the MIU feature on this projector support Multi PC mode.• If the projector is required to display an image sent by other PC, execute the QUIT PRESENTER MODE function.
• See the User’s Manual – Network Guide for details.  (84)
MULTI PC MODE
The projector supports the Single PC mode that displays an image on full screen sent by 1 PC, and the Multi PC mode that divides the screen into 4 zone and displays 
images in each zone sent by up to 4 PCs. The MULTI PC MODE function switches these modes.
SINGLEUse the ▲/▼ buttons to select an item, and the ENTER or INPUT button to perform the item. The mode will be switched from the Multi PC mode to the Single PC mode and the quarter screen identified in the menu will be displayed on full screen.
MULTIUse the ENTER or INPUT button to perform the item.  The mode will be switched to the Multi PC mode and the screen will be divided to 4 zones.• If the Presenter Mode is set to on in the PC whose image is currently displayed on screen, a message, QUIT PRESENTER MODE, will be displayed in about 3 seconds when the function is performed.• The function is available when there is any PC 
connected to the projector in the Multi PC mode set in the Live Viewer 3 software.
(continued on next page) 
						

							
55

MIU menu
MIU menu (continued)
ItemDescription
LIVE MODE SETTING(continued)
DISPLAY USER NAME
Selecting this item displays the Display User Name defined in the Live View3 software in the PC whose image is on screen.
SINGLE PC modeThe Display User Name will be shown in the DISPLAY USER NAME box.
ExamplesDisplay User name   Shown in the DISPLAY USER NAME boxPC_NAME0001               PC_NAME0001(remained as default)            Unnamed(blank space )                   (prohibited showing)           (Anonymous)
If there is no PC in the Single PC mode connected to the projector, the DISPLAY USER NAME box is shown as right.
MULTI PC modeThe Display User Names will be shown in the DISPLAY USER NAME box.
• See the User’s Manual – Network Guide for details of 
the Display User Name setting. (22)
PC-LESS PRESENTATION
Selecting this item displays the PC-LESS PRESENTATION menu.Using the menu is able to make the projector display the images stored in an SD memory card or a USB memory, and realizes a presentation without a PC.Use the ▲/▼/◄/► buttons to select an item, and the ► or ENTER button to perform the item.• While displaying the image, to press the MENU button displays the PC-LESS PRESENTATION menu.
THUMBNAIL
Use the ▲/▼/◄/► buttons to select an image, and press 
the ENTER or INPUT button to display the image.
SLIDE SHOWSlide show will start when you press the ENTER or ► button.
(continued on next page) 
						

							
56

MIU menu
MIU menu (continued)
ItemDescription
PC-LESS PRESENTATION(continued)
DIRECTORY
Use the ▲/▼ buttons to select an image or a folder, and press the ENTER button to display the image or turn into the THUMBNAIL.To open or close the folder, press the ►/◄ buttons.
DISPLAY SIZE
Use the ▲/▼ buttons to set the display size.
KEY CONFIG.
Use the ▲/▼ buttons to select key configuration from the 2 patterns.
REMOVE MEDIA
Use the ▲/▼ buttons to select a remove mode, and then the ENTER or ► button is pressed so the menu will appear.
• Also these items can be set with Web Remote Control (Refer to Network Guide) except REMOVE MEDIA. 
SETUP
Selecting this item displays the MIU SETUP menu.
Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.
DHCP (Dynamic Host Configuration Protocol)
Use the ▲/▼ buttons to turn DHCP on/off.
ON ó OFF
Select OFF when the network does  not have DHCP enabled.
• When the “DHCP” setting changes to “ON”, it takes a little time to obtain IP address from DHCP server.• Auto IP function will be assigned an IP address if the projector could not obtain an IP address from server even if DHCP is “ON”.
(continued on next page) 
						

							
57

MIUmenu
MIU menu (continued)
ItemDescription
SETUP(continued)
IP ADDRESS
Use the ▲/▼/◄/► buttons to enter the IP ADDRESS. This function can only be used when DHCP is set to OFF.
• The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network.• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET MASK
Use the ▲/▼/◄/► buttons to enter the same SUBNET MASK used by your PC. This function can only be used when DHCP is set to OFF.
• The SUBNET MASK ”0.0.0.0” is prohibited.
DEFAULT GATEWAY
Use the ▲/▼/◄/► buttons to enter the DEFAULT GATEWAY (a node on a computer network that serves as an access point to another network) address.This function can only be used when DHCP is set to OFF.
DNS 
SERVER
Use the ▲/▼/◄/► buttons to input the DNS server address. The 
DNS server is a system to control domain names and IP addresses on the Network. 
TIME DIFFERENCE
Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your IT manager. Use the ◄ button to return to the menu after setting the TIME DIFFERENCE.
DATE AND TIME
Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.
• The projector will override this setting and retrieve DATE AND TIME information from the Time server when SNTP is enabled. ( Date/Time Settings of the User’s Manual - Network Guide)
(continued on next page) 
						

							
58

MIU menu
MIU menu (continued)
ItemDescription
SETUP(continued)
MODE
Use the ▲/▼ buttons to select the mode of the network communication system. Select it according to the setting of your PC.
ADHOC ó INFRASTRUCTURE
CH
Use the ▲/▼ buttons to select the channel of the wireless LAN while using it. Select it according to the setting of your PC.The channels 1 to 11 are available.
• The available channels would be various depending on a country. In addition, wireless network card might be required due to the standard.
ENCRYPTION
Use the ▲/▼ buttons to select the encryption method to be used.
WPA2-PSK(AES)    ô
WPA-PSK(AES) ó WPA-PSK(TKIP) ó WEP 128bit ó WEP 64bit ó OFF
SSID
Use the ▲/▼ buttons to select the SSID to display the SSID menu.
DEFAULTPressing the ► or ENTER button when one of the  DEFAULT (#1~#4) is selected. 
CUSTOMPress the ► or ENTER button when the # 5 CUSTOM is selected. The SSID #5 CUSTOM menu will be appeared.(1)  
The current SSID will be displayed on the first line. If not yet written, the line will be blank.  Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. The RESET button can be used to erase 1 character at a time. Also if you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER or INPUT button, 1 character or all characters will be erased.The SSID can be input up to 32 characters. 
(continued on next page) 
						

							
59

MIU menu
MIU menu (continued)
ItemDescription
SETUP(continued)
SSID (continued)
(2)  
To change an already inserted character, press the ▲/▼ button to move the cursor to one of the first 2 lines, and use the ◄/► buttons to move the cursor on the character to be changed. After pressing the ENTER or INPUT button, the character is selected.  Then, follow the same procedure as described at the item (1) above
(3)   
To finish entering text, move the cursor to the SAVE 
on screen and press the ENTER or INPUT button.   To revert to the previous SSID without saving changes, move the cursor to the CANCEL on screen and press the ENTER or INPUT button.
SPEED
Use the ▲/▼ buttons to select the transfer rate.(M : Mbps : Megabits per second)
AUTOó54Mó48Mó36Mó24Mó18M ô               ô
1Mó2Mó5.5Mó6Mó9Mó11Mó12M
• The AUTO mode automatically selects the optimum rate.• Transfer rates may change due to the network situation.
NETWORK MODE
Use the ▲/▼ buttons to select the network mode.
WIRELESS ó WIRED
• The network mode will be initialized whenever the power is turned on with the power switch.• The WIRELESS will be enabled when the wireless network card is inserted.• The WIRED will be enabled when the wireless network card is not inserted.
(continued on next page) 
						

							
60

MIU menu
MIU menu (continued)
ItemDescription
PROJECTOR NAME(1)  
Use the▲/▼ buttons on the MIU menu to select the 
PROJECTOR NAME menu and press the ► button. The PROJECTOR NAME dialog will be displayed.
(2)   
The current PROJECTOR NAME 
will be displayed on the first 3 lines. If not yet written, the lines will be blank. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. The RESET button can be used to erase 1 character at a time. Also if you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER or INPUT button, 1 character or all characters will be erased.The PROJECTOR NAME can be input up to 64.
(3)   
To change an already inserted 
character, press the ▲/▼ button to move the cursor to one of the first 3 lines, and use the ◄/► buttons to move the cursor on the character to be changed. After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (2) above.
 (4)   
To finish entering text, move the 
cursor to the SAVE on screen and press the ENTER or INPUT button. To revert to the previous PROJECTOR NAME without saving changes, move the cursor to the CANCEL on screen and press the ENTER or INPUT button.
(continued on next page)