Hitachi Cp-X3010n Projector Users Manual

							31
IMAGE menu
ItemDescription
H PHASE
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right  ó Left
• This item can be selected only for a computer signal or a 
component video signal.
H SIZE Using the ◄/► buttons adjusts the horizontal size.
Small  ó Large
• This item can be selected only for a computer signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the  RESET button on the remote control during this 
operation.
• Images might appear degraded when this function is operated, but 
it is not a malfunction.
AUTO ADJUST  EXECUTE Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
menu (
 33). The vertical position and horizontal position will be 
automatically set to the default.
For a component video signal
The vertical position, horizontal position and horizontal phase will be 
automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
• When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black 
frame may be displayed on the edge of the screen, depending on 
the computer model. 
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION menu (
 46). 
						

							32
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
PROGRESSIVE Using the ▲/▼ buttons switches the progress mode.
TV  ó FILM 
ó OFF
  
• This function is performed only for a video signal, s-video signal or 
component video signal of 480i@60 or 576i@50.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select OFF, even 
though the screen image may lose sharpness.
VIDEO NR Using the ▲/▼ buttons switches the noise reduction mode.
HIGH  ó MID 
ó LOW
   
• This function is performed only for a video signal, s-video signal or 
component video signal of 480i@60 or 576i@50.
• When this function is excessive, it may cause a certain 
degradation of the picture. 
COLOR SPACE Using the ▲/▼ buttons switches the mode for color space.
AUTO  ó RGB 
ó SMPTE240 
ó REC709 
ó REC601
      
• This item can be selected only for a computer signal or a 
component video signal (except SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
COMPONENT Using the ▲/▼ buttons switches the function of the COMPONENT 
(Y, Cb/Pb, Cr/Pr)
 port.
COMPONENT  ó SCART RGB
When the SCART RGB is selected, the COMPONENT (Y, Cb/
Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. 
A SCART adapter or SCART cable is required for a SCART RGB 
input to the projector. For details, contact your dealer.
(continued on next page) 
						

							33
INPUT menu
ItemDescription
VIDEO FORMAT The video format for S-VIDEO port and VIDEO port can be set.
(1)   Use the ▲/▼ buttons to 
select the input port.
S-VIDEO  ó VIDEO
(2)   Using the ◄/► buttons 
switches the mode for video 
format.
AUTO   ó  NTSC  
ó  PAL  
ó  SECAM
      N-PAL  ó M-PAL 
ó NTSC4.43 
• This item is performed only for a video signal from the  VIDEO port 
or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode according to the input signal.
COMPUTER IN The computer input signal type for 
COMPUTER IN1 and IN2 ports 
can be set.
(1)  
Use the ▲/▼ buttons to select the COMPUTER IN port to be set.
COMPUTER IN1  ó COMPUTER IN2
(2)   Use the ◄/► buttons to select   
the computer input signal type.
AUTO  ó SYNC ON G OFF
• Selecting the AUTO mode allows   
you to input a sync on G signal or component video signal from the 
port.
• In the AUTO mode, the picture may be distorted with certain 
input signals. In such a case, remove the signal connector so that 
no signal is received and select the SYNC ON G OFF, and then 
reconnect the signal.
FRAME LOCK Set the frame lock function on/off for each port.
(1)  
Use the ▲/▼ buttons to select 
the input ports.
COMPUTER IN1  ó COMPUTER IN2
(2)   Use the ◄/► buttons to turn the 
frame lock function on/off .
ON  ó OFF
• This item can be performed only on a signal with a vertical 
frequency of 49 to 51Hz, 59 to 61 Hz.
• When ON is selected, moving pictures are displayed more 
smoothly.
• This function may cause a certain degradation of the picture. In 
such a case, please select OFF.
(continued on next page) 
						

							34
INPUT menu
ItemDescription
RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input 
signals can be set on this projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or ENTER button when 
selecting a STANDARD resolution will 
automatically adjust the horizontal and 
vertical positions, clock phase and 
horizontal size.
The INPUT_INFORMATION dialog will be 
displayed.
(4)    To set a custom resolution use the ▲/▼ buttons to select 
the CUSTOM and the RESOLUTION_CUSTOM box will be 
displayed. 
Set the horizontal (HORZ) and 
vertical (VERT) resolutions using 
the ▲/▼/◄/► buttons.  
This function is may not support all 
resolutions.
(5)   Move the cursor to OK on screen and press the ► or ENTER 
button. The message "ARE YOU SURE YOU WISH TO 
CHANGE RESOLUTION?" appears. To save the setting, press 
the ► button.   
The horizontal and vertical positions, clock phase and horizontal 
size will be automatically adjusted.
After the INPUT_INFORMATION 
dialog has displayed for a few 
seconds, the screen will return to the 
RESOLUTION menu displaying the 
changed resolution.
(6)    To revert back to the previous 
resolution without saving changes, 
move the cursor to CANCEL on 
screen and press the ◄ or ENTER 
button. 
The screen will then return to the 
RESOLUTION menu displaying the 
previous resolution.
• For some pictures, this function may not work well.
STANDARD   ↓
CUSTOM  ↓ 
						

							35
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
AUTO KEYSTONE 
EXECUTE Selecting this item performs the Automatic keystone distortion 
correction. Projector automatically corrects vertical keystone 
distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. 
When the slant of the projector is changed, execute this function 
again.
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When V:INVERT or H&V:INVERT is selected to the MIRROR item 
in the SETUP menu, if the projector screen is inclined or angled 
downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the projector is placed on the level (about ±3°), this function 
may not work.
• When the projector is inclined to near ±30 degree or over, this 
function may not work well.
• This function will be unavailable when the Transition Detector is on
 
(
 59).
KEYSTONE Using the ◄/►
 buttons corrects the vertical keystone distortion.
Shrink the bottom of the image  ó Shrink the top of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• This function will be unavailable when the Transition Detector is on  
(
 59).
ECO MODE Using the ▲/▼ buttons turns off/on the eco mode.
NORMAL  ó ECO
• When the ECO is selected, acoustic noise and screen brightness 
are reduced.
(continued on next page) 
						

							36
SETUP menu
ItemDescription
MIRROR Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL 
ó H:INVERT 
ó V:INVERT 
ó H&V:INVERT
     
If the Transition Detector is on and MIRROR status is changed, 
TRANSITION DETECTOR ON alarm ( 59) will be displayed when 
projector is restarted after the AC power is turned off.
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL  ó SAVING
When SAVING is selected, the power consumption in the standby 
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to NETWORK 
BRIDGE, all of the RS-232C commands are disabled  (
48).
• When SAVING is selected, AUDIO OUT STANDBY setting of 
AUDIO SOURCE (
 37) is invalid, and no signal is output from 
AUDIO OUT port in the standby mode.
MONITOR OUT The combination of a picture shown on screen and output from the
MONITOR OUT port can be arranged in the menu.
The picture coming into the port selected in the (2) is output to the
MONITOR OUT port while an image from the port chosen in the (1) is on screen.
(1) Choose a picture input port using ▲/▼ buttons.
• Choose STANDBY, to select the output  
signal from the MONITOR OUT port in the standby mode. 
STANDBY settings can be selected individually for NORMAL or 
SAVING, which is selected in the STANDBY MODE (

above).
(2) Select one of the COMPUTER IN ports using ◄/► buttons. Choosing the COMPUTER IN1 allows the following choice.
COMPUTER IN1  ó OFF
Choosing the COMPUTER IN2 allows the following choice. COMPUTER IN2  ó OFF
Choosing other input or STANDBY allows the following choice. COMPUTER IN1  ó COMPUTER IN2 
ó OFF
                
• OFF disables the MONITOR OUT port.
• Initial settings for STANDBY are the following: COMPUTER IN1 
when NORMAL is selected in STANDBY MODE; and OFF when 
SAVING is selected in STANDBY MODE.
COMPUTER IN1   ó  COMPUTER IN2      
                     
STANDBY
                                     
COMPONENT  VIDEO 
ó S-VIDEO 
ó (Y, Cb/Pb, Cr/Pr) 
						

							37
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table 
below can be performed. Select an item using the 
▲/▼ cursor buttons, and press the ► cursor button 
or the ENTER button to execute the item. Then 
perform it according to the following table.
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume.
High  ó Low
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE The combination of a picture and audio input port can be arranged 
in the menu.
The audio coming into the port selected in the (2) is output while an 
image from the port chosen in the (1) is on screen.
(1)  
Choose a picture input port using the ▲/▼ buttons.
• Choose AUDIO OUT STANDBY, to   
select the audio output to the  AUDIO OUT port in the standby 
mode. The built-in speaker does not work in the standby mode.
• While RETURN is selected, pressing the  ◄ button returns to the 
previous menu.
(2)   Select one of the AUDIO IN ports using ◄/► buttons.
AUDIO IN1 
ó AUDIO IN2 
ó AUDIO IN3 
ó         
•  disables the audio output.
• C.C. (Closed Caption) is automatically activated when  is selected 
and an input signal containing C.C. is received. This function is 
available only when the signal is NTSC for VIDEO or S-VIDEO, or 
480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2, 
and when AUTO is selected for DISPLAY in the C.C. menu under the 
SCREEN menu (
 42). 
COMPUTER IN1  
ó  COMPUTER IN2      
                    
AUDIO OUT STANDBY
                                      COMPONENT
 VIDEO  ó S-VIDEO 
ó (Y, Cb/Pb, Cr/Pr) 
						

							38
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
LANGUAGE Using the ▲/▼/◄/►
 buttons switches the OSD (On Screen 
Display) language.
ENGLISH  ó FRANÇAIS 
ó DEUTSCH 
ó  ESPAÑOL
       
  (shown in the LANGUAGE dialog)  
Press the ENTER or INPUT button to save the language setting.
MENU POSITION Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the 
MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
 
( 22). It is displayed by pressing the 
BLANK button on the remote 
control.
MyScreen  ó ORIGINAL 
ó BLUE 
ó WHITE 
ó BLACK
       
MyScreen :  Screen can be registered by the MyScreen item ( 39).ORIGINAL
 :  Screen preset as the standard screen.
BLUE, WHITE, BLACK :   Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected. MyScreen  ó ORIGINAL 
ó OFF
       
MyScreen :  Screen can be registered by the MyScreen item ( 39).ORIGINAL
 :  Screen preset as the standard screen.
OFF  :  Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the BLANK screen  (
above) after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, 
the plain black screen is instead used.
• When the ON is selected to the MyScreen PASSWORD item in 
the SECURITY menu (
 57), the START UP is fixed to MyScreen.
(continued on next page) 
						

							39
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1.  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from 
the current screen.
Please wait for the target image to be displayed, and press the 
ENTER or INPUT button when the image is displayed. The image 
will freeze and the frame for capturing will appear. 
To stop performing, press the RESET button on the remote 
control. 
2.   Using the ▲/▼/◄/► buttons adjusts the 
frame position.  
Please move the frame to the position 
of the image which you want to use. The 
frame may not be able to be moved for 
some input signals.  
To start registration, press the ENTER 
or INPUT button on the remote control.
To restore the screen and return to the previous dialog, press the 
RESET button on the remote control. 
Registration takes several minutes.  
When the registration is completed, the registered screen and the 
following message is displayed for several seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed: “A capturing error has occurred. Please try again.” 
• This function cannot be selected when the ON is selected to the 
MyScreen Lock item (
 40).
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 57).
(continued on next page) 
						

							40
SCREEN menu
ItemDescription
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  ó OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 57).
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
ON  ó OFF
When the ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the ACTIVE IRIS displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by 
pressing the  FREEZE button.
The indication of the TEMPLATE displayed by changing.
• When the OFF is selected, please remember if the picture is 
frozen. Do not mistake freezing for a malfunction  (
22).
(continued on next page)