Hitachi Cp-X301 Projector Users Manual

							


Operating
1.Press the MENU button on the remote control or the projector.  
The Advanced Menu or EASY MENU, which has priority just after powered 
on will appear. 
If you want to move the menu position, use the cursor buttons after pressing 
the POSITION button. While the projector is displaying any menu, the MENU 
button on the projector works as the cursor buttons.
Using the menu function
2.If you want to change it to the Advanced Menu, 
select the Go to Advanced Menu...
This projector has the following menus:  
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, C.C. and EASY 
MENU.  
EASY MENU consists of functions often used, and the other menus are classified 
into each purpose and brought together as the Advanced Menu.
Each of these menus is operated using the same methods. The basic operations 
of these menus are as follows.
In the EASY MENU
3.Use the ▲/▼ cursor buttons to select an item to 
operate.
4.Use the ◄/► cursor buttons to operate the item.
MENU button
VIDEODOC.CAMERA
KEYSTONEASPECTSEARCHBLANKMUTEMY BUTTONPOSITION1 2
ESCENTERMENURESETCOMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNo
ONOFF
9×
FREEZE
RESET button
ENTER buttonMENU buttonCursor buttons
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE      UPVOLUME
DOWNo
ON
OFF
9×FREEZE
ESC button
EASY MENU
(continued on next page) 
						

							


Operating
Using the menu function (continued)●   Some functions cannot be performed when a certain input port is selected, or 
when a certain input signal is displayed.
● 
 
When you want to reset the operation, press RESET button on the remote 
control during the operation. Note that some items (ex. LANGUAGE, H 
PHASE, VOLUME) cannot be reset.
● 
 
In the Advanced Menu, when you want to return to the previous display, press 
the ◄ cursor button or ESC button on the remote control.
5.Press MENU button on the remote control again to close the menu and 
complete this operation. Even if you do not do anything, the dialog will 
automatically disappear after about 10 seconds.
2.Use the ▲/▼ cursor buttons to select a menu. 
If you want to change it to the EASY MENU, select 
EASY MENU. 
Then press the ► cursor button, or ENTER button to 
select an item. The lower layer menu of the selected 
item will appear.
In the Advanced Menu
3.Use the ▲/▼ cursor buttons to select an item to operate. 
Then press the ► cursor button, or ENTER button to progress. The operation 
menu of the selected item will appear.
4.Use the ▲/▼ cursor buttons to operate the item.
Advanced Menu 
						

							
3

EASY MENU
EASY MENU
From the EASY MENU, items shown in the table below 
can be performed. 
Select an item using the ▲/▼ cursor buttons. Then 
perform it according to the following table. 
ItemDescription
ASPECTUsing the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu (28).
AUTO 
KEYSTONE EXECUTE
Using the ► button executes the auto keystone function. See AUTO KEYSTONE  EXECUTE item in SETUP menu (33).
KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.See KEYSTONE  item in SETUP menu (33).
 PICTURE MODE
Using the ◄/► buttons switches the picture mode. 
The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source.
         NORMAL ó CINEMA ó DYNAMIC ó BOARD(BLACK)
      DAYTIME ó WHITEBOARD ó BOARD(GREEN) 
COLOR TEMPGAMMA
NORMAL#2 MID DEFAULT#1 DEFAULT
CINEMA#3 LOW DEFAULT#2 DEFAULT
DYNAMIC#1 HIGH DEFAULT#3 DEFAULT
BOARD(BLACK)#4 Hi-BRIGHT-1 DEFAULT#4 DEFAULT
BOARD(GREEN)#5 Hi-BRIGHT-2 DEFAULT#4 DEFAULT
WHITEBOARD#2 MID DEFAULT#5 DEFAULT
DAYTIME#6 Hi-BRIGHT-3 DEFAULT#6 DEFAULT
• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to GAMMA (25) and COLOR TEMP (26) items in PICTURE menu.• When this function is performed, a certain extra such as a line may appear.
(continued on next page) 
						

							
4

EASY MENU
EASY MENU (continued)
ItemDescription
BRIGHTNESSUsing the ◄/► buttons adjusts the brightness.See BRIGHTNESS item in PICTURE menu (25).
CONTRASTUsing the ◄/► buttons adjusts the contrast.See CONTRAST item in PICTURE menu (25).
COLORUsing the ◄/► buttons adjusts the strength of whole color.See COLOR item in PICTURE menu (26).
TINTUsing the ◄/► buttons adjusts the tint.See TINT item in PICTURE menu (26).
SHARPNESSUsing the ◄/► buttons adjusts the sharpness.See SHARPNESS item in PICTURE menu (27).
WHISPERUsing the ◄/► buttons turns off/on the whisper mode.See WHISPER item in SETUP menu (34).
MIRRORUsing the ◄/► buttons switches the mode for mirror status.
See MIRROR item in SETUP menu (34).
RESET
Performing this item resets all of EASY MENU items except FILTER TIME and LANGUAGE.A dialog is displayed for confirmation. Selecting RESET using the ▲ button performs resetting.
FILTER TIME
The usage time of the air filter is shown in the menu.Performing this item resets the filter time which counts usage time of the air filter.
A dialog is displayed for confirmation. Selecting RESET using the ▲ button performs resetting. 
See FILTER TIME item in OPTION menu (41).
LANGUAGEUsing the ◄/► buttons changes the display language. See LANGUAGE item in SCREEN menu (36).
Go toAdvanced Menu...
Select Go to Advanced Menu… on the menu, and press the ► or ENTER button to use the menu of PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION or C.C.. 
						

							
5

PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table 
below can be performed. 
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the 
item. Then perform it according to the following table.
ItemDescription
BRIGHTNESSUsing the ▲/▼ buttons adjusts the brightness.Light ó Dark
CONTRASTUsing the ▲/▼ buttons adjusts the contrast.Strong ó Weak
GAMMA
Using the ▲/▼ buttons switches the gamma mode.
To adjust CUSTOM
Selecting a mode whose name includes CUSTOM and then pressing the ► button 
or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.
Choose an item using the ◄/► buttons, and  adjust the level using the ▲/▼ buttons. 
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.
  No pattern ð Gray scale of 9 steps 
                 Ramp  Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the test 
pattern  (Gray  scale  of  9  steps),  except  the  darkest  in  the  left  end. 
If  you  want  to  adjust  the  2nd  tone  from  left  end  on  the  test  pattern 
use  the  equalizing  adjustment  bar  “1”.  The  darkest  tone  at  the  left 
end  of  the  test  pattern  cannot  be  controlled  with  any  of  equalizing 
adjustment bar.
• When this function is performed, lines or other distortion may appear .
#1 DEFAULT � #1 CUSTOM � #2 DEFAULT � #2 CUSTOM �#3 DEFAULT�#3 CUSTOM�#5 CUSTOM � #5 DEFAULT � #4 CUSTOM � #4 DEFAULT  
�#6 CUSTOM�#6 DEFAULT�
(continued on next page) 
						

							
6

PICTURE menu
PICTURE menu (continued)
ItemDescription
COLOR TEMP
Using the ▲/▼ buttons switches the color temperature mode.
To adjust CUSTOM
Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
OFFSET adjustments change the color intensity on the whole tones of the test pattern.
GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.
Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons. 
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button.  Each time you press the ENTER button, the pattern changes as 
below.
  No pattern ð Gray scale of 9 steps 
                 Ramp  Gray scale of 15 steps
• When this function is performed, lines or other distortion may 
appear.
COLOR
Using the ▲/▼ buttons adjusts the strength of whole color.
Strong ó Weak
• This item can be selected only for a video signal, s-video or component video signal.
TINT
Using the ▲/▼ buttons adjusts the tint.
Greenish ó Reddish
• This item can be selected only for a video signal, s-video or component video signal.
�#2 MID CUSTOM�#3 LOW DEFAULT�#3 LOW CUSTOM�
#1 HIGH DEFAULT � #1 HIGH CUSTOM � #2 MID DEFAULT�#6 Hi-BRIGHT-3 CUSTOM�#6 Hi-BRIGHT-3 DEFAULT�#5 Hi-BRIGHT-2 CUSTOM� #5 Hi-BRIGHT-2 DEFAULT � #4 Hi-BRIGHT-1 CUSTOM � #4 Hi-BRIGHT-1 DEFAULT  
(continued on next page) 
						

							
7

PICTURE menu
PICTURE menu (continued)
ItemDescription
SHARPNESS
Using the ▲/▼ buttons adjusts the sharpness.
Strong ó Weak• There may be some noise and/or the screen may flicker for a 
moment when an adjustment is made. This is not a malfunction.
MY MEMORY
This projector has 4 memories for adjustment data (for all the items of PICTURE menu).Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.
LOAD-1 ó LOAD-2 ó LOAD-3 ó LOAD-4
SAVE-4 óSAVE-3 ó SAVE-2 ó SAVE-1
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked in the number included in the function’s name, and adjusts the picture automatically depending on the data. 
• The LOAD functions whose linked memory has no data are skipped.• Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.• There may be some noise and the screen may flicker for a moment when loading data. This is not malfunction.• You can perform the LOAD function using MY BUTTONs. Please see MY BUTTON item in OPTION menu (42).
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function’s name. 
• Remember that the current data being stored of a memory will be lost by saving a new data into the memory. 
						

							
8

IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the item. 
Then perform it according to the following table.
ItemDescription
ASPECT
Using the ▲/▼ buttons switches the mode for aspect ratio. For a computer signal
NORMAL ó 4:3 ó 16:9 ó SMALL         
For a Video signal, S-video signal or Component video signal4:3 ó 16:9 ó 14:9 ó SMALL     
For no signal4:3 (fixed)• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN
Using the ▲/▼ buttons adjusts the over-scan ratio.
Large (It reduces picture) ó Small (It magnifies picture)
• This item can be selected only for a video, s-video and component video signal.• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the ▲/▼ buttons adjusts the vertical position.
Up ó Down
• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the default setting.  Pressing RESET button when V POSITION is selected will reset V POSITION to the default setting.• When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on OVER SCAN (above) setting. It is not possible to adjust when OVER SCAN is set to 10.
(continued on next page) 
						

							
9

IMAGE menu
IMAGE menu (continued)
ItemDescription
H POSITION
Using the ▲/▼ buttons adjusts the horizontal position.
Left ó Right
• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to the default setting. Pressing RESET button when H POSITION is selected will reset H POSITION to the default setting.• When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on OVER SCAN (28) setting. It is not possible to adjust when OVER SCAN is set to 10.
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker .
Right ó Left
• This item can be selected only for a computer signal or component video signal. 
H SIZE
Using the ▲/▼ buttons adjusts the horizontal size.
Large ó Small
• This item can be selected only for a computer signal.• When this adjustment is excessive, the picture may not be displayed correctly.  In such a case, please reset the adjustment by pressing the RESET button during this operation.
AUTO ADJUST EXECUTE
Executing this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal phase (43) will be automatically adjusted. Make sure that the application window is set  to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signalThe video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu (31). The vertical position and horizontal position will be automatically set to the default. 
For a component video signalThe vertical position, horizontal position and horizontal phase will be automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input. When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.• The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (43). 
						

							
30

INPUT menu
INPUT menu
From the INPUT menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to execute 
the item. Then perform it according to the following 
table.
ItemDescription
PROGRESSIVE
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó TURN OFF     
• This function is performed only for an interlaced signal at the VIDEO or S-VIDEO input, and for 525i (480i) or 625i (576i) signal at the COMPONENT VIDEO.• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.
VIDEO NR
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW      
• This function is performed only for the VIDEO or S-VIDEO input, 
and for 525i (480i) or 625i (576i) signal at the COMPONENT VIDEO.• When this function is excessive, it may cause a certain degradation of the picture. 
COLOR SPACE
Using the ▲/▼ buttons switches the mode for color space. 
AUTO ó RGB ó SMPTE240 ó REC709 ó REC601      
• This item can be selected only for a computer signal or component video signal except SCART RGB signal.• The AUTO mode automatically selects the optimum mode. • The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
COMPONENT
Using the ▲/▼ buttons switches the function of the COMPONENT(Y, Cb/Pb, Cr/Pr) port.
COMPONENT ó SCART RGB
When  the  SCART  RGB  is  selected,  COMPONENT  (Y,  Cb/Pb,  Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART cable  is  required  for  a  SCART  RGB  input  to  the  projector.  For  your reference, see the TECHNICAL part.
(continued on next page)