Hitachi Cp-X1230 Users Manual

31
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
MESSAGE
Select the TURN ON or the TURN OFF using the  /  buttons. :
TURN ON 
TURN OFF
When the TURN ON is selected, the following message function works.
The message of the “AUTO IN PROGRESS” for the auto adjustment. 
The message of the ”NO INPUT IS DETECTED”
The message of the ”SYNC IS OUT OF RANGE”
The message of the ”Searching …”
The message of the “Detecting …”
The indication of the input signal by input...

32
Multifunctional Settings (continued) Multifunctional Settings (continued)
OPTION Menu
With the  OPTION menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
: SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTIONVOLUME
SPEAKER
IR REMOTE
LAMP TIME
FILTER TIME
SERVICE
RESET16
TURN ON
1:    2:    3:
1234 h
4321 h
ItemDescription
VOLUMEAdjust the volume using the  /  buttons. : 
High 
Low
SPEAKERSelect the TURN ON...

33
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
SERVICE
Pressing the (or the ENTER) button calls the SERVICE
menu. 
SERVICE Menu
Select an item using the  /  buttons, and press the
(or the ENTER) button to per form each function. :
FANSPEED 
AUTO ADJUST 
LENS LOCK
FANSPEED
Select the fan speed level using the  /  buttons. :
HIGH 
NORMAL
The HIGH ups rotation speeds of fans, though. Please use this
function in using a projector at highlands etc.
memoNote that...

34
Lamp Lamp
The projector uses a high-pressure mercury glass lamp. The lamp can break with aloud bang, or burn out,if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn out soon after
you start using them. In addition, when the bulb bursts, it is possible for shards of
glassto fly into the lamp housing, and for gas containing mercuryto escape from the
projector’s vent holes.
About disposal of a lamp• This product contains a...

35
Lamp (continued) Lamp (continued)
After making sure that the projector has cooled
adequately, slide the knob of a lamp cover lock as
shown in the Figure. Then, one side of the lamp
cover is raised. Pull up the lamp cover and remove
it, as shown in the Figure. If the indicators or a message prompts you to replace the lamp, replace the lamp as soon
as possible.
Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at
least 45 minutes.
2
1
Contact your dealer to prepare a new...

Apply a vacuum cleaner to the top of the filter cover and
the air filter to clean.
If the soiling will not come off the air filter, or it becomes
damaged, it needs to be replaced.
If the air filter needs to be replaced, contact your dealer
to prepare a new air filter. Tell the dealer your air filter
type.
36
Caring For The Air Filter 
Air Filter Air Filter
WARNING• Please carefully read the “User’s Manual - Safety Guide.
• Before caring, make sure the power switch is off and the power cable is not...

37
Other Care Other Care
WARNING• Please carefully read the “User’s Manual - Safety Guide”.
• Before caring, make sure the power switch is off and the power cable is not
plugged in.
• Be cautious of high temperature. Do not touch about the lens and ventilation
openings during use or immediately after use prevent a burn. 
• Never try to care for the inside of the unit yourself. Doing so is dangerous.
CAUTION
• Incorrect care could have adverse influence such as discoloration,
peeling paint, etc. 
• Do not...

38
T T
roubleshooting roubleshooting
Related Messages
When the units power is on, messages such as those shown below may be displayed.
When any such message is displayed on the screen, please respond as described below.
If the same message is displayed after the treatment, or if a message other than the
following appears, please contact your dealer or service company.
memoAlthough these messages will be automatically disappeared around several
minutes, it will be reappeared every time the power is turned...

39 Related Messages
(continued)
T T
roubleshooting (continued) roubleshooting (continued)
MessageDescription
CLEAN THE AIR FILTER
POWER OFF FIRST,
THEN CLEAN THE AIR FILTER.
AFTER CLEANING THE AIR
FILTER,
RESET THE FILTER TIMER.
The time the filter timer has counted has reached 100
hours. 
Please clear or change the air filter by referring to the section
“Air Filter”. After caring for the air filter, please be sure to reset
the filter timer.
CHECK THE AIR FLOW
The internal portion temperature is...

40
T T
roubleshooting (continued) roubleshooting (continued)
Regarding The Indicator Lamps
Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP
indicator have the meanings as described in the table below. Please respond in
accordance with the instructions within the table. If the same indication is displayed after
the treatment, or if an indication other than the following is displayed, please contact your
dealer or service company.
• 
When the interior portion has become...