Hitachi Cp-S210 Users Manual

							31
OPTION Menu
With the OPTION menu, the items shown in the table below can be performed.
Perform each operation in accordance with the instructions in the table below.
: SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTIONVOLUME
SCREEN TYPE
LAMP TIME
FILTER TIME
RESET16
4:3
1234h
    21h
ItemDescription
VOLUMEAdjust Volume:High ñLow
SCREEN TYPE
Select the Screen Type:4:3 ñ16:9 ñ16:9 ñ16-9 •Please select the screen type used and the picture position in case of 16:9.
This selection is used as basic information for a suitable display. This function
should be performed before other picture adjustment.
LAMP TIME
To begin the operation of this item, please press the  button of the
projector or the RESET button of the remote control for 3 seconds.
Reset the Lamp Timer: 
Selecting the RESET performs this function.
RESET CANCEL
•The numerical value of four digits shown on this menu is the projector use
time since the last RESET operation of this item. The value is reset to 0 at the
same time the RESET is selected.
•The value of this function is used to display the message of “CHANGE THE
LAMP”. So this function must be performed only immediately after replacing
the lamp. 
Do not perform this function unless you have replaced the lamp. Perform this
function every time the lamp is replaced. Incorrect performing of this function
causes incorrect operation of the message function.
•Please see to the section “Lamp” about replacing the lamp.
FILTER TIME
To begin the operation of this item, please press the  button of the
projector or the RESET button of the remote control for 3 seconds.
Reset the Filter Timer: 
Selecting the RESET performs this function.
RESET CANCEL
•The numerical value of four digits shown on this menu is the projector use
time since the last RESET operation of this item. The value is reset to 0 at the
same time the RESET is selected.
•The value of this function is used to display the message of “CLEAN THE AIR
FILTER”. So this function must be performed only immediately after cleaning
or replacing the air filter. 
Do not perform this function unless you have cleaned or replaced the air filter.
Perform this function every time the air filter is cleaned or replaced. Incorrect
performing of this function causes incorrect operation of the message
function.
•Please see to the section “Air Filter” about cleaning and replacing the air
filter.
RESET
Reset the OPTION Menu Items:
Selecting the EXECUTE performs this function.
EXECUTE CANCEL
•The SCREEN TYPE item is returned to the initial setting. Note that the items
VOLUME, LAMP TIME and FILTER TIME are not reset.
ð
ð
ð
Multifunctional Settings (continued) 
						

							32
Lamp
The projector uses a high-pressure mercury glass lamp. The lamp can break with aloud bang, or burn out,if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn out soon after
you start using them. In addition, when the bulb bursts, it is possible for shards of
glassto fly into the lamp housing, and for gas containing mercuryto escape from the
projector’s vent holes.
• If the lamp should break (it will make a loud bang when it does), unplug the power
cord from the outlet, and make sure to request a replacement lamp from your local
dealer. Note that shards of glass could damage the projector’s internals, or cause
injury during handling, so please do not try to clean the projector or replace the lamp
yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the room
well, and make sure not to breathe the gas that comes out of the projector vents, or
get it in your eyes or mouth.
• Do not open the lamp cover while the projector is suspended from above. This is
dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover
is opened. In addition, working in high places is dangerous, so ask your local dealer
to have the lamp replaced even if the bulb is not broken
• If the indicators or a message prompts you to replace the lamp (see the section
“Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon
as possible. Using the lamp for long periods of time, or past the replacement date,
could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.
• If the lamp breaks soon after the first time it is used, it is possible that there are
electrical problems elsewhere besides the lamp. If this happens, contact your local
dealer or a service representative.
• Use the lamp of the specified type only.Type number: DT00581
(sold separately)
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Before replacing the lamp, make sure the power switch is off and the power cable is
not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling
the lamp while hot can cause burns, as well as damaging the lamp.
• Do not use the projector with the lamp cover removed. At the lamp replacing, make
sure that the screws are screwed in firmly. Loose screws could result in damage or
injury.
• Obey local ordinances when disposing of used lamps. In most cases, it is possible to
dispose of used bulbs in the same manner as used glass bottles, but in some cases,
bulbs are sorted separately.
WARNINGHIGH VOLTAGE    HIGH TEMPERATURE    HIGH PRESSURE 
						

							33
1Turn off the projector, and unplug the power cord. Allow the lamp
bulb to cool for at least 45 minutes.
6Insert the new lamp, and tighten the 2
screws firmly to lock it in place.
Slide the lamp cover into place until it locks into position.
Slowly turn the projector so that the top is facing up.
3After making sure that the projector
has cooled adequately, slowly flip
over the projector, so that the bottom
is facing up.
4Hold the release button while sliding
and taking up the lamp cover.
2Contact your local dealer to prepare a new lamp. Tell the dealer
your lamp type number. If the projector is mounted on the ceiling,
or if the lamp has broken, also ask the dealer to replace the lamp.
9Turn on the projector, and reset the lamp timer. When the lamp has
been replaced after the message of “THE POWER WILL TURN OFF
AFTER 0hr.” is displayed, complete the following operation within
10 minutes of switching power on.
(1) While the projector running, press the MENU button to open the menu.
(2) Choose the “OPTION” on the menu using the 
/ button, then press the  button
or ENTER button.
(3) Choose the “LAMP TIME” using the 
/ button, then press and hold the  button
of projector or the RESET button of remote control for 3 seconds.
(4) Choose the “RESET” using the  button.
In the case of replacement by yourself,
5Unscrew the 2 screws, and slowly
pick up the lamp by the handles.
Replacing The Lamp 
WARNING• Please carefully read the “User’s Manual - Safety Guide”.
CAUTION
• Do not reset the lamp timer without replacing the lamp. 
• When you replace the lamp, please replace also the air filter. The air filter may be
attached when you buy a replacement lamp for this projector. Please ask your dealer.
If the indicators or a message prompts you to replace the lamp, replace the lamp as soon
as possible. Using the lamp for long periods of time, or past the replacement date, could
cause it to burst. If the projector is mounted on the ceiling, or if the lamp has broken, do
not try to clean the projector or replace the lamp yourself.
Lamp cover
Release button
Handles
Screws
7
8
Lamp (continued) 
						

							34
Air Filter
Caring For The Air Filter
The air filter should be cleaned about every 100 hours. If the indicators or a message
prompts you to clean the air filter (see the section “Related Messages” and “Regarding
The Indicator Lamps”), clean the air filter as soon as possible. If the air filter becomes
clogged by dust or the like, internal temperature rises and could cause malfunction.
1Turn off the projector, and unplug the power cord.
2Apply a vacuum cleaner to
the top of the filter cover to
clean the air filter.
3Reset the filter timer.
Filter Cover
WARNING• Please carefully read the “User’s Manual - Safety Guide”.
• Before replacing the air filter, make sure the power switch is off and the power cable
is not plugged in.
• Use the air filter of the specified type only. Type number:
NJ08292(sold separately)
• Do not use the projector with the air filter and filter cover removed. The use without
the air filter could result in damage.
CAUTION
• Do not reset the filter timer without cleaning or replacing the air filter.
• If the air filter becomes clogged by dust or the like, internal temperature rises and
could cause malfunction. The power is automatically turned off in order to prevent the
projector from overheating internally.
• When you replace the lamp, please replace also the air filter. The air filter may be
attached when you buy a replacement lamp for this projector. Please ask your dealer.
(1) Turn on the projector. While the projector running, press the MENU button to
open the menu.
(2) Choose the “OPTION” on the menu using the 
/ button, then press the 
button or ENTER button.
(3) Choose the “FILTER TIME” using the 
/ button, then press and hold the
button of projector or the RESET button of remote control for 3 seconds.
(4) Choose the “RESET” using the  button. 
						

							35
Replacing The Air Filter
Filter cover
Air filter Release buttons
Release buttons
Turn off the projector, and unplug the power cord.
2Contact your local dealer to prepare a
new air filter. Tell the dealer your air
filter type number.
4Hold the release buttons of the air
filter, while pulling down it. 
3After making sure that the projector
has cooled adequately, remove the
filter cover. Hold the release buttons of
the filter cover, while pulling up it.
6Reset the filter timer.
(1)  Turn on the projector. While the projector running, press the MENU button to
open the menu.
(2) Choose the “OPTION” on the menu using the 
/ button, then press the 
button or ENTER button.
(3) Choose the “FILTER TIME” using the 
/ button, then press and hold the
button of projector or the RESET button of remote control for 3 seconds.
(4) Choose the “RESET” using the  button.
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be
replaced. Please replace the air filter as soon as possible.
1
Insert a new air filter, and replace the filter cover.5
Air Filter (continued) 
						

							36
Other Care
WARNING•Please carefully read the “User’s Manual - Safety Guide”.
• Before replacing the air filter, make sure the power switch is off and the power cable
is not plugged in.
ATTENTION
• Do not use cleaners or chemicals other than those listed below,
including benzene and paint thinner.
• Do not use aerosols or sprays.
• Do not polish or wipe with hard objects.
Caring For The Inside Of The Projector
Caring For The Lens
In order to ensure the safe use of your projector, please have it cleaned and inspected by
your local dealer about once every 2 years. Never try to care for the inside of the unit
yourself. Doing so is dangerous.
1Turn off the projector, and unplug the
power cord.
2Lightly wipe the lens with a
commercially available lens-cleaning
wipe. Do not touch the lens directly
with your hand.
Caring For The Cabinet And Remote Control
1Turn off the projector, and unplug the power cord.
2Wipe lightly with gauze or a soft cloth. 
If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and
wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
Lens 
						

							37
Troubleshooting
Related Messages
When the units power is ON, messages such as those shown below may be displayed.
When any such message is displayed on the screen, please respond as described
below. If the same message is displayed after the treatment, or if a message other than
the following appears, please contact your dealer or service company.
MessageDescription
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
(*1)Lamp usage time is approaching 2000 hours. (*2) 
Preparation of a new lamp, and an early lamp change is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
(*1)Lamp usage time is approaching 2000 hours. (*2) 
A lamp change within ** hours is recommended. When lamp
usage reaches 2000 hours, the power will automatically be
turned OFF. Please change the lamp by referring to the “Lamp”
section of this manual. After you have changed the lamp,
please be sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.As lamp use has reached 2000 hours (*2), the power will soon
be automatically turned OFF. 
Please immediately turn the power off, and change the lamp by
referring to the “Lamp” section of this manual. After you have
changed the lamp, please be sure to reset the lamp timer.
NO INPUT IS DETECTED
ON ***There is no input signal. 
Please confirm the signal input connection, and the status of the
signal source.
SYNC IS OUT OF RANGE
ON ***        *****kHz         *****HzThe horizontal or vertical wavelength of the inputted signal is
outside of the response parameters of this unit. 
Please confirm the specs for this unit or the signal source
specs.
CHECK THE AIR FLOW
The internal portion temperature is rising. 
Please turn the power OFF, and allow the unit to cool down at
least 20 minutes. After having confirmed the following items,
please turn the power ON again.
• Is there blockage of the air passage aperture?• Is the air filter dirty?• Does the peripheral temperature exceed 35°C?
(*1) • Although this message will be automatically disappeared after around 3 minutes, it will be reappeared
every time the power is turned ON.
(*2) • Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no
longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, such that
the power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, however,
that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the
functioning of the automatic shut-down function of this unit.NOTE
fHfV 
						

							38Wipe the dust-detecting window by
using a soft cloth.
Troubleshooting (continued)
Related Messages
(continued)
MessageDescription
CLEAN THE AIR FILTER
POWER OFF FIRST,
THEN CLEAN THE AIR FILTER.
AFTER CLEANING THE AIR
FILTER,
RESET THE FILTER TIMER.A note of precaution when cleaning the air filter. 
Please immediately turn the power OFF, and clean or change
the air filter by referring to the “Air Filter” section of this manual.
After you have cleaned or changed the air filter, please be sure
to reset the filter timer.
If the same message is displayed after the treatment, please
clean the transparent area of filter cover and the dust-detecting
window, according to the following.
ATTENTION• The transparent area of filter cover and the dust-detecting window
should be cleaned for normal operation of the optical dust detecting system. Please
pay attention not to remain fiber or fragment of cloth inside the duct.
Filter cover
Air filter Release buttons
Release buttons
Turn off the projector, and unplug the
power cord.
2After making sure that the projector
has cooled adequately, remove the
filter cover. 
Hold the release buttons of the filter cover, while
pulling up it.
4Remove the air filter.
Hold the release buttons of the air filter, while pulling
down it. 
1
Replace the air filter and filter cover.
Transparent areaFilter cover
Dust detecting window
3Wipe the transparent area of the filter
cover by using a swab or a soft cloth. 
5
6
(Rear side)
(Bottom side) 
						

							39
ATTENTION• When the interior portion has become overheated, for safety
purposes, the power source is automatically turned off, and the indicator lamps may
also be turned off. In such a case, press the “Ó” (power OFF) side of the main power
switch, and wait at least 45 minutes. After the unit has sufficiently cooled down, please
make confirmation of the attachment state of the lamp and lamp cover, and then turn
the power on again.
Regarding The Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator
have the meanings as described in the table below. Please respond in accordance with the
instructions within the table. If the same indication is displayed after the treatment, or if an
indication other than the following is displayed, please contact your dealer or service
company.
POWER
indicatorLAMP
indicatorTEMP
indicatorDescription
Lighting in
orangeTurned offTurned offThe unit is in a standby state. Please refer to the “Power
ON/OFF” section of this manual.
Flashing in
greenTurned offTurned offThe unit is warming up. Please wait.
Lighting in
greenTurned offTurned offThe unit is in an ON state. Ordinary operations may be
performed.
Flashing in
orangeTurned offTurned offThe unit is cooling down. Please wait.
Blinking in
red--
The unit is cooling down. A certain error has been detected.
Wait until the POWER indicator has finished flashing, and then
perform the proper response measure using the item
descriptions below as reference.
Lighting or
blinking in
redLighting in
redTurned off
The projector lamp has not been properly fixed (attached),
the projector lamp does not light, and/or there is a possibility
that the interior portion has become heated. Turn the power
OFF and wait at least 20 minutes. After the unit has sufficiently
cooled down, please make confirmation of the following items,
and then turn the power ON again. If the same indication is
displayed, please change the lamp.
• Is there blockage of the air passage aperture?
• Is the air filter is dirty?
• Does the peripheral temperature exceed 35°C?
Lighting or
blinking in
red Blinking in
redTurned off
The lamp cover has not been properly fixed (attached). Turn
the power OFF and wait at least 45 minutes. After the unit has
sufficiently cooled down, please make confirmation of the
attachment state of the lamp and lamp cover, and then turn
the power ON again.
Troubleshooting (continued) 
						

							40
POWER
indicatorLAMP
indicatorTEMP
indicatorDescription
Lighting or
blinking in
redTurned offBlinking in
red
The cooling fan is not operating. Turn the power OFF and wait
at least 20 minutes. After the unit has sufficiently cooled down,
please make confirmation of the following item, and then
resent the power to ON.
• Is there no foreign matter caught in the cooling fan?
Lighting or
blinking in
red
Turned offLighting in
red
There is a possibility that the interior portion has become
heated. Turn the power OFF and wait at least 20 minutes.
After the unit has sufficiently cooled down, please make
confirmation of the following item, and then resent the power
to ON.
• Is there blockage of the air passage aperture?
•  Is the air filter is dirty?
• Does the peripheral temperature exceed 35°C?
Lighting in
greenAlternative blinking in
the redThere is a possibility that the interior portion has become
overcooled. Please use the unit within the usage temperature
parameters (0°C to 35°C). After the treatment, resent the
power to ON.
Lighting in
greenSimultaneous blinking
in red
It is time to clean the air filter, or there is no air filter. Please
immediately turn the power OFF, and clean or change the air
filter by referring to the “Air Filter” section of this manual. After
you have cleaned or changed the air filter, please be sure to
reset the filter timer. After the treatment, resent the power to
ON.
Regarding The Indicator Lamps 
(continued)
Troubleshooting (continued)