Hitachi Cp-A220n Users Manual

							11
Connecting with your devices (continued)
(continued on next page)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
-   Some signal may need an adapter to input this projector.
-   Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
-    Although the projector can display signals with resolution up to UXGA   
(1600X1200), the signal will be converted to the projector’s panel resolution 
before being displayed. The best display performance will be achieved if the 
resolutions of the input signal and the projector panel are identical.
•   If you connect this projector and a notebook computer, you need output the 
display to an external monitor, or output simultaneously to the internal display 
and an external monitor. Consult the computer's manual for the setting.
•   Depending on the input signal, the automatic adjustment function of this 
projector may take some time and not function correctly. 
-   Note  that  a  composite  sync  signal  or  sync-on-green  signal  may  confuse  the 
automatic adjustment function of this projector  (
40). 
-   If the automatic adjustment function does not work correctly, you may not see 
the dialog to set the display resolution.  In such a case, use an external display 
device.  You  may  be  able  to  see  the  dialog  and  set  an  appropriate  display 
resolution.
NOTE
Setting up 
						

							12
Connecting with your devices (continued)
Setting up
•  If you insert a USB storage device, such as a USB memory, into the USB TYPE 
A port and select the port as the input source, you can view images stored in the 
device (
77).
•    You can connect a dynamic microphone to the  MIC port with a 3.5 mm mini-plug. 
In that case, the built-in speaker outputs the sound from the microphone, even 
while the sound from the projector is output. You can input line level signal to the 
MIC port from equipment such as wireless microphone. Select HIGH in the MIC 
LEVEL item of the AUDIO menu when you input line level audio signal to the 
MIC port. In the normal mode, the volume of the microphone can be adjusted 
separately from the volume of the projector using the menu.  (
46)  
    In the standby mode, the volume of the microphone is adjustable with the 
VOLUME +/-  buttons on the remote control, in synchronization with the volume 
of the projector. (
20)   
    Even when the sound of projector is set to mute mode by the AUDIO SOURCE 
function (
45), the  volume of the microphone is adjustable.  
    In both modes (standby or normal), the  MUTE button on the remote control 
works on the sounds of the microphone and the projector. (
20)
• If a loud feedback noise is produced from the speaker, move the 
microphone away from the speaker. 
•  This projector doesn't support plug-in power for the microphone.
NOTE
(continued on next page)
►Before removing the USB storage device from the port of the 
projector, be sure to use the REMOVE USB function on the thumbnail screen to 
secure your data  (
80).
CAUTION
Monitor
COMPUTER IN1
COMPUTER IN2HDMIUSB TYPE B
S-VIDEO
VIDEOAUDIO OUT
AUDIO IN3
AUDIO IN1
AUDIO IN2MIC
MONITOR OUT
CONTROL
     USB
TYPE A
   DC5V 
     0.5A
R LRGB IN
USB storage 
device
Microphone systemSpeakers(with an amplifier) 
						

							13
Connecting with your devices (continued)
To use network functions of the projector, connect the LAN port with the 
computer's LAN port, or with an access point that is connected to the computer 
with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, 
also connect the  CONTROL port and an RS-232C port of the external device to 
communicate as a network terminal. See the  User's Manual - Network Guide for 
details of the network functions.
Setting up
►Before connecting the projector to a network system be sure 
to obtain the consent of the administrator of the network  (
64).
►
Do not connect the LAN port to any network that might have the excessive voltage.
CAUTION
• If an oversized USB storage device blocks the  LAN port, use a USB 
extension cable to connect the USB storage device. NOTE
COMPUTER IN1
COMPUTER IN2HDMIUSB TYPE B
S-VIDEO
VIDEOAUDIO OUT
AUDIO IN3
AUDIO IN1
AUDIO IN2MIC
MONITOR OUT
CONTROL
     USB
TYPE A
   DC5V 
     0.5A
RS-232CLANAccess pointComputer 
						

							14
Setting up
Connecting to a power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult 
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power 
cord. The power outlet should be close to the projector and easily accessible. 
Remove the power cord for complete separation.
• Never modify the power cord.  WARNING
Using the security bar and slot
A commercial anti-theft chain or wire up to 
10 mm in diameter can be attached to the 
security bar on the projector.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bar and slot to prevent the projector 
from falling down, since it is not designed for it. WARNING
►Do not place anti-theft chain or wire near the exhaust vents. 
 
It may become too hot.  CAUTION
• 
The security bar and slot is not comprehensive theft prevention 
measures. It is intended to be used as supplemental theft prevention measure. NOTE
Please remember that when the DIRECT POWER 
ON function activated (
53), the connection of the 
power supply make the projector turn on.
AC IN Power cord
Security bar
Security slot
Anti-theft chain or wire 
						

							15
Using the cable cover
Utilize the cable cover as the guard and blind for the connecting parts.
1. Connect the signal cables and the power cord to the projector first.
2. Combine parts as shown in figure,  
and assemble the cable cover. 
3 . Insert the three knobs on the cable cover into the three holes on the projector 
as shown in the figure. Pass the cables through the holes on the bottom of 
the cable cover. 
1
2
31
2
3
1
2
3
1
2
3
knobs
Setting up
► Be careful not to pinch the cables in the cable cover, to 
prevent damage to the cables.
► Use the cable cover that is supplied with the projector. Do not attempt any 
modifications to the cable cover.  CAUTION 
						

							16
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote control for 
long period, remove the batteries from the remote control and store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 or R6P) 
according to their plus and minus terminals 
as indicated in the remote control.
3.Replace the battery cover in the direction of the arrow and snap it back into place.
►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of dif ferent 
types at the same time. Do not mix a new battery with used one. 
• 
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery .
• 
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. 
If the leakage adheres to your body or clothes, rinse well with water immediately .
• Obey the local laws on disposing the battery. WARNING
• The remote control signal reflected in the screen or the like may be available. 
If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.
• The remote control uses infrared light to send signals to the projector (Class 1 
LED), so be sure to use the remote control in an area free from obstacles that 
could block the remote control’s signal to the projector.
• 
The remote control may not work correctly if strong light (such as direct sun 
light) or light from an extremely close range (such as from an inverter fluorescent 
lamp) shines on the remote sensor of the projector. Adjust the position of 
projector avoiding those lights.
NOTE
2
1 3
Remote  
sensor
30º 30º
Approx.
3 m  
						

							17
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the computer, when the projector’s USB 
TYPE B port and the computer’s type A USB port are 
connected and MOUSE is selected for the USB TYPE B 
item in the OPTION menu (
54).
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button:  Press ENTER button.
(4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.
(5) ESC key: Press ESC button.
(6) Mouse right button:  Press RESET button.
►Improper use of the simple mouse & keyboard 
function could damage your equipment. While using this 
function, please connect this product only to a computer. Be 
sure to check your computer’s manuals before connecting this 
product to the computer.NOTICE
When the simple mouse & keyboard function of this product does not work 
correctly, please check the following.
• When a USB cable connects this projector with a computer having a built-in pointing 
device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external 
mouse and disable the built-in pointing device, because the built-in pointing device may 
have priority to this function.
• 
Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work 
depending on the computer’s configurations and mouse drivers. This function can work with the 
computer which can operate general USB mouse or keyboard.
•  You cannot do things like press two buttons at once (for instance, pressing two buttons 
at the same time to move the mouse pointer diagonally).
• 
This function is activated only when the projector is working properly. This function is not 
available in any of the following cases:
- While the lamp is warming up. (The POWER indicator blinks in green.)
- When either USB TYPE A or USB TYPE B port is selected.
- While displaying BLANK 
(27), TEMPLATE (51) or MY IMAGE (67) screen.
- When any menu is displayed on the screen.
- 
While using the cursor buttons to operate the sound or screen functions such as adjusting the 
sound volume, correcting the keystone, correcting the picture position and magnifying the screen.
NOTE
(1) Set to Mode 1:NORMAL...  VOLUME - and RESET buttons 
(2) Set to Mode 2:HIGH...  MAGNIFY OFF and ESC buttons
Please remember that the REMOTE FREQ. in the SERVICE item of 
the OPTION menu
 (60) of the projector to be controlled should be 
set to the same mode as the remote control. (1)
(2)
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTOMAGNIFYVOLUME
ー
ONOFF＋
FREEZE
      FOCUS                             D-ZOOM-           +           -            +
PAGE
       UP
DOWN
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTOMAGNIFYVOLUME
ー
ONOFF＋
FREEZE
      FOCUS                             D-ZOOM-           +           -            +
PAGE
       UP
DOWN
(1)
(3)
(5) (2)
(4)
(6)
USB TYPE B
USB TYPE B
 
port 
						

							18
Power on/off
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
98).
3.Confirm that there is nothing that the lens 
door hits while opening. Press STANDBY/
ON button on the projector or the 
remote control. The lens door opens, the 
projection lamp lights up, and the POWER  
indicator begins to blink green. When the 
power is completely on, the indicator will 
stop blinking and light in steady green 
(
98).
Power on/off
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTONPOSITION1 2
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTOMAGNIFYVOLUMEー
ONOFF＋
FREEZE
      FOCUS                             D-ZOOM-           +           -            +
PAGE
       UPDOWN
VIDEODOC.CAMERA
KEYSTON
E
ASPECT SEARCH
BLANK
MUTE
MY BUTTO N
POSITION
12
ESC ENTERMENURESET
COMPUTER
MY SOURCE/
AUTO
MAGNIF
YPAGE
      UPVOLUME
DOWNo
ONOF
F
9×
FREEZE
STANDBY/ON button
POWER indicator
WARNING  ►Never look into the projection lens or mirror while 
the projection lamp lights, since the projection lamp ray may cause 
a trouble on your eyes.
►
Be careful not to pinch your finger with the lens door, to prevent an injury.
►Do not place the projector vertically with the lens door open as 
shown in the figure on the right. It could cause malfunction or injury.
►Do not stand under the projector mounted on the wall or ceiling, 
when its lens door is opening or closing. Moreover, do not look at the 
mirror when the lens door is opening or closing.
►Never touch a lens door or mirror. If the mirror is broken, the 
projected image will be distorted. Close the lens door, and contact 
your dealer. 
						

							19
Power on/off
►Be careful not to pinch your finger with the lens door, to 
prevent an injury.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be 
close to the projector and easily accessible. WARNING
1.Press the STANDBY/ON button on the projector or the remote control. 
 
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Confirm that there is nothing that the lens door hits while closing. 
Press the STANDBY/ON button again while the message appears.   
The projector lamp will go off, and the POWER indicator will begin blinking in 
orange. The lens door will close right after the lamp goes off.
However, to maintain better picture quality, the lens door will close after the 
lamp has been cooled down when the projector is installed upside down such 
as in ceiling mount installation. Then POWER indicator will stop blinking and 
light in steady orange when the lamp cooling is complete (
98).
Do not turn the projector on for about 10 minutes or more after turning it of f. 
Also, do not turn the projector off shortly after turning it on. Such operations might 
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• 
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON 
( 53) and AUTO POWER OFF ( 54) 
items of the OPTION menu.
NOTE 
						

							20
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●   When 
 is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO SOURCE item of AUDIO menu (
45).
●   Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions are true:
-    An option other than 
 is selected for STANDBY in the AUDIO SOURCE 
item of the AUDIO menu  (
45).
- NORMAL is selected in the STANDBY MODE item of the SETUP menu ( 44).
●   In the standby mode, the volume of the microphone is adjustable with the  
VOLUME +/- buttons on the remote control, in synchronization with the volume 
of the projector 
(
12) .
1.Press MUTE button on the remote control.  
A dialog will appear on the screen indicating that you have muted 
the sound. 
 
To restore the sound, press the  MUTE, VOLUME + or 
VOLUME - button. Even if you do not do anything, the dialog 
will automatically disappear after a few seconds.
Temporarily muting the sound
●   When  is selected for current picture input port, the sound is always muted. 
Please see AUDIO SOURCE item of AUDIO menu (
45).
●   C.C. (Closed Caption) is automatically activated when sound is muted and an 
input signal containing C.C. is received. This function is available only when 
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN1 
or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. 
menu under the SCREEN menu (
52).
1.Press INPUT button on the projector.  
Each time you press the button, the projector 
switches its input port from the current port as below.
Selecting an input signal
(continued on next page)
●  While ON is selected for AUTO SEARCH item in OPTION menu ( 53), the projector 
will keep checking the ports in above order repeatedly till an input signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTO
MAGNIFYVOLUME
ー
ONOFF
＋
FREEZE
      FOCUS                             D-ZOOM-           +           -            +
PAGE
       UP
DOWN
VOLUME +/- button
MUTE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTO
MAGNIFYVOLUME
ー
ONOFF
＋
FREEZE
      FOCUS                             D-ZOOM-           +           -            +
PAGE
       UP
DOWN
                COMPUTER IN1  COMPUTER IN2  
    VIDEO                                                             LAN
    S-VIDEO                                           USB TYPE A
                
    HDMI      
 USB TYPE B
INPUT button