Hitachi 32ld8800ta User Manual

9
COMPONENT NAMES
Main Unit
Front Panel
q  Cabinet
w  Panel
e  Indicating Lamp
r  Remote Control Receiver
t  Speaker
y  Main Power Switch (on the bottom surface)
u  Desktop Stand (optional for 37LD8800TA)
Rear Panel
q  Handgrips
w  Side Input
e  
Terminal Board (External Device Connection)
r  Power Cord Socket
t  Control Panel (see below for details)
Please refer to 
13~17 for the detailed 
information for the connections.
Control Panel (including Card Slot)
q  SD Memory Card Slot
w  Sub Power button
e...

10
ENGLISH
COMPONENT NAMES (Continued)
Remote Control
q  Sub Power
w  Function Select (TV/DVD/SAT)
     Press this button to select function mode 
indicating LED lamp.
    Normally, select “TV”.
e  
Input Select/DVD Control/Photo Input Control    Press this button to change input mode. 
     In addition, you can use these buttons while 
operating the selected brand of DVD player or 
Photo Input function.
r  Menu
t  Cursor
y  OK
u  Sound Mode
     Sound mode can be changed each time pressed 
in the...

11
Caution When Moving the Main Unit
As this product is heavy, whenever it is moved, two people are required to transport it safely.
When transferring the unit, hold the unit by using the handgrips at the backside of the panel. (See the fi gures below 
for details.)
32LD8800TA:
PREPARATION
Remote Control Batteries Installation
This remote control operates on 2 “AA” batteries.
1. Open the batter y compartment cover
 Slide open the battery compartment cover on the backside of the 
remote control in the...

12
ENGLISH
PREPARATION (continued)
Safety Precaution on Main Unit Installation
Read SAFETY PRECAUTIONS ( 3 to6 ) carefully besides this page. 
*When installing the monitor, use the Desktop Stand (SD8G4237/ optional for 37LD8800TA). Please refer to the user 
manual of the stand. The Desktop Stand has been used for the illustration in this manual.
Anti-Tumble Measures
Install in a stable place and implement safety measure against overturning.When installing the main unit, be sure to use the specifi ed mount...

13
CONNECTION
Terminal Positions
Rear
q  Power Cord Socket
w  Aerial Socket
e  AV 1
r  AV 2
t  AV 3
y  AV 4
u  Monitor Out and Sub Woofer
i  Service use only
o   
Power Swivel Terminal 
(see 
36)
a   PC Connection terminals
(D-sub 15 pin and mini stereo for 
Audio)
s   HDMI1, 2 and mini stereo for Audio 
Side
d  AV 5
f  Headphone input
g  Photo Input terminal
h  SD Memory Card slot
Connecting Procedure
Your monitor is ready for various kinds of connections. Make a connection in the following steps. Be...

14
ENGLISH
CONNECTION (continued)
Connecting Procedure (continued)
3. Connecting to External Equipment
 Terminals on Rear
AV1 and AV2 can be connected to the equipment with either Component or Composite output. Depending on whether the 
Y/VIDEO input of your selected equipment is Y signal or Video signal, it automatically regards as Component or Composite. 
When using as Composite, do not insert the jacks into PB or PR.
 If your external device has a Component terminal, COMPONENT connection is...

15
CONNECTION (continued)
Connecting Procedure (continued)
Monitor Out can be used to display same image as main unit on another monitor.
When this output terminal is connected to an external monitor with a 75 Ohm terminal, the same image from 
composite(AV1~5), or S-Video(AV3,5), or RF signal can be displayed to the external monitor. 
Sub Woofer terminal can bring the deep bass sound from the external speaker.
PC terminals (D-sub 15 pin + audio) is connected to PC, which allows Analog RGB signal. 
HDMI...

16
ENGLISH
CONNECTION (continued)
Connecting Procedure (continued)
 Terminals on Side
Since the following terminals are located on the side, it is very convenient to use the extra device on a temporary 
basis after done the connections on the rear panel. 
AV 5 can be connected to the equipment with an S-Video output and composite output. 
 If your external device has a S-video terminal, S-VIDEO connection is recommended for higher quality picture.
Headphone The detail settings can be adjusted from Audio...

17
CONNECTION (continued)
Connecting Procedure (continued)
4. Connecting the plug into the wall socket
Connect the Power Cord after completing all other connections.
(The type of plug is different from this drawing for some countries.)
CAUTION
 
Use only the Power Cord provided.
 
Do not use a power supply voltage other than that indicated(AC100-240V, 50/60Hz). It may cause fi re or electric shock.
 For the LCD panel, a three-core power cord with a ground terminal is used for effi ciency protection. Always...

18
ENGLISH
BASIC OPERATION
Power On/Off
Now, turn On the main power of the unit.  Make sure that the Power Cord 
has plugged into the wall socket.
 To tur n On the power of  the monitor:
1.  Press the Main Power switch on the monitor.
  The Indicating Lamp will illuminates in Red (Standby mode).
2.  Press Sub Power button either on the control panel or on the remote 
control.
  The color of the Indicating Lamp turns into Green, and the image will 
display on the screen. 
 To tur n Off  the power of  the...