Home > Heckler and Koch > Firearms > Heckler And Koch HK USP Tactical, USP Expert Operators Manual

Heckler And Koch HK USP Tactical, USP Expert Operators Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Heckler And Koch HK USP Tactical, USP Expert Operators Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 26 Heckler and Koch manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							41
    •  Barrel locking block
    •  Slide rails and grooves
    •  All operating controls
    •  Detent plate & detent slide (items 26 & 36, see
    diagram on pages 46 & 48)
    •  Locking insert and guiding part in frame
    •  Extractor
    Heavy Lube
    Lubrication runs down the surface when it is held in a verti-
    cal position
    No heavy lube is required on the HK USP.
    Reapply lubricant periodically during firing as it burns off
    from the heat. Apply lubricant using a clean shaving brush,
    cotton swabs, patches, or rag. A spray bottle of lubricant
    also works well when using compressed air to circulate the
    lubricant into all parts and to remove the excess from the
    pistol.
    Troubleshooting Problems and Repair 
    The ten inspection areas listed above should be checked
    prior to contacting HK if your pistol fails to function 
    properly. Other common causes of problems that are oftenoverlooked include:
    •  Fouled or improperly lubricated pistol 
    •  Bad ammunition 
    •  Damaged magazines
    •  Operator error
    If your HK USP still fails to function, please contact Heckler
    & Koch Customer Service at (703) 450-1900 for the name
    and address of your nearest HK Authorized Repair Facility.
    Military and law enforcement users, contact your unit
    armorer or HK Customer Service.
    NOTE: If after reviewing this manual you still have
    questions, please contact your HK dealer or
    telephone the Heckler & Koch Customer Service
    Department. Please address any suggested changes
    or improvements to this manual to the HK Creative
    Services Department. 
    						
    							42
    The Mark II HK UTL can be quickly attached or removed
    from the pistol and provides an immediate source of
    illumination. With easy to use controls, the UTL ensures law
    enforcement professionals or home owners can identify po-
    tential threats in critical low light situations.
    Using a USP fitted with a UTL makes alignment of the light
    and pistol easier than using a separate flashlight. A separate
    light can be difficult to use and hold while manipulating a
    pistol in a life threatening situation. The UTL can also be
    detached from the pistol and used in place of a conventional
    flashlight.
    The Mark II UTL is designed and manufactured by Insight
    Technology Inc. (ITI), the same firm that created the special
    flashlight and laser aiming module used on the .45 caliber HK
    Mark 23 pistol developed for the US Special Operations
    Command.
    Available exclusively from Heckler & Koch, Inc., the Mark II
    UTL fits all variants of the USP pistol, including the USP
    Compact, and can be purchased with an optional remote
    cable switch, and tactical nylon carrying pouch.
    USP ACCESSORIES
    Heckler & Koch and Insight Technology Inc. have developed a
    powerful accessory light that attaches to the HK USP pistol.
    Smaller and more powerful than a conventional flash-light,
    the Mark II HK Universal Tactical Light (UTL) adds a dimen-
    sion of tactical flexibility to the USP absent in other modern
    semiautomatic pistols.
    Figure 42
    The Mark II UTL is a compact and powerful 
    accessory light for the USP.  
    						
    							43
    Key features of the HK UTL
    • compact and rugged design fits all models of the USP
    and USP Compact pistol
    • lamp brightness superior to most flashlights  
    • focusable beam, spot to flood
    • clip-on/clip-off design, can be installed or removed in
    seconds
    • integral on-off switch prevents inadvertent operation
    Figure 43
    The HK Mark II UTL can be installed and removed
    from any USP in seconds with one hand.• uses easily replaceable standard lithium batteries
    • fingertip on-off operation (toggle switch pushed to
    right, intermittent on only, toggle switch pushed to
    left, intermittent and constant on)
    • optional remote switch and accessory pouch available
    Other USP Accessories
    A variety of USP accessories and enhancements are available
    and include tritium sights, click adjustable sights, a sight
    installation tool, and ambidextrous control levers. Contact
    HK for a complete list and pricing.  
    						
    							44 44
    SECTION 8  EXPLODED DIAGRAM & PARTS LIST
    Figure 44
    USP (.40 S&W and 9mm Models)  
    						
    							45 45
    Item Description Identification No. Item Description Identification No.
    Item Description Identification No.
    USP Parts List (.40 S&W and 9mm Models)
    1 Extractor spring 214188
    2 Extractor 214187
    3 Roll pin,
    ISO 8748 - 3 X 14 mm (3x)980838
    (extractor, firing pin, mag release)
    4 Front sight* (6.4 mm)214220
    Front sight* (6.6 mm)214221
    Front sight* (6.8 mm) 
    standard214222
    Front sight*(7.0 mm)214223
    Front sight* (7.2 mm)214224
    Front sight* (7.4 mm)214225
    6 Rear sight 214194
    7 Barrel (.40 S&W)214209
    Barrel(9 X 19 mm)214344
    8 Slide(.40 S&W)214186
    Slide, complete** (.40 S&W) 214150
    Slide(9 X 19 mm)214304
    Slide, complete** (9 mm x 19)214345 
    9 Firing pin spring 214190
    10 Firing pin 214189
    11 Firing pin block spring 214192
    12 Firing pin block 214191
    13 Recoil spring 214148
    13A Front recoil spring retainer 214721
    13B Snap ring 929191
    14 Buffer spring retainer 214208
    15 Buffer spring 214207
    16 Recoil spring retainer 214206
    17 Recoil spring guide rod 214205
    17 Recoil/buffer spring assembly 
    complete with captive recoil spring**
    18 Roll pin,
    ISO 8748 - 3.5 X 10mm982782
    (buffer spring retainer)
    19 Slide release 214181
    20 Trigger bar,complete21417621 Trigger bar detent 214165
    22 Trigger bar detent spring 214166
    23 Disconnector 214840
    23A Disconnector** 214160
    24 Sear axle 214101
    25 Catch 214773
    25A Control latch 214817
    25B Catch (old style)** 214159
    26 Detent plate (variant 1 & 2)214099
    Detent plate** (variant 3 & 4)214254
    Detent plate** (v.5,6,9,& 10)214255
    27 Shaped spring (slide release)214171
    28 Flat spring 214167
    29 Hammer (variant 1-4, 9 & 10)214825
    Hammer, complete** 214301
    with pin (variant 1-4, 9 & 10)
    29A Hammer (variant 1-4, 9 & 10)** 214106
    30 Hammer,bobbed (v.5, 6, 7)214256
    Hammer, bobbed, complete** 214308
    with pin (variant 5, 6, 7)
    31 Cyl. pin,
    ISO 8750 -1.5 X 8mm982783
    (hammer strut pin)
    32 Hammer axle (new style)214774
    Hammer axle** (v.1-6, 9, 10)214303
    Hammer axle** (variant 7)214258
    33 Control lever(variant 1, 5, 9)214184
    Control lever (variant 2, 6, 10)214309
    Control lever(variant 3)214352
    Control lever (variant 4)214253
    34 Sear (variant 1-4, 9, 10)214180
    Sear, complete** 214179
    34A Tube (variant 5, 6, 7)**214413
    35 Roll pin,ISO 8748 - 2 X 10mm982785
    (sear, variant 1, 2, 3, 4, 9, 10)36 Detent slide 
    (variant 1-6, 9, 10)214105
    37 Compression spring, 214104
    (detent slide) variant 1-6, 9, 10
    38 Frame, incomplete 214172
    39 Trigger rebound spring 214164
    40 Trigger axle 214154
    41 Trigger 214153
    42 Magazine release 214169
    43 Magazine release spring 214170
    44 Hammer strut (new style) 214819
    Hammer strut** 214157
    45 Hammer spring 214300
    46 Lanyard loop insert 214341
    47 Lanyard loop insert pin 214314
    48 Magazine follower 214211
    Mag. follower
    (10-rd, .40 & 9mm)** 214211
    49 Magazine spring 214212
    Magazine spring 
    (10-rd)** 214850
    50 Floorplate 214213
    Floorplate (10-rd, .40 cal.)** 214845
    Floorplate (10-rd, 9mm)** 214848
    51 Locking plate 214288
    52 Magazine housing 
    (13-rd, .40 cal.)214214
    Magazine housing (15rd, 9mm)214350
    Magazine housing (10rd, .40 cal.)214846
    Magazine housing (10rd, .9mm)214849
    Locking plate (10rd, .40 cal.)** 214844
    Locking plate (10rd, .9mm)** 214847
    Magazine complete (10rd, .40 cal.)** 214854
    Magazine complete (10rd, 9mm)** 214855
    Magazine complete (13rd, .40 cal.)** 214864
    Magazine complete (15rd, 9mm)** 214866
    **Not pictured in diagram 
    						
    							46 46
    Figure 46
    USP (.45 ACP Model)  
    						
    							47 47
    Item Description Identification No. Item Description Identification No.
    Item Description Identification No.
    1 Extractor spring 214188
    2Extractor 214828
    3 Roll pin,
    ISO 8748 - 3 X 14 mm(3x)980838
    (extractor, firing pin, mag. release)
    4 Front sight* (6.4 mm)214220
    Front sight* (6.6 mm)214221
    Front sight* (6.8 mm) 
    standard214222
    Front sight*(7.0 mm)214223
    Front sight* (7.2 mm)214224
    Front sight* (7.4 mm)214225
    6 Rear sight 214194
    7Barrel 214815
    8Slide, incomplete 214827
    Slide, complete 214826
    9 Firing pin spring 214190
    10 Firing pin 214189
    11 Firing pin block spring 214192
    12 Firing pin block 214191
    13Recoil spring 214843
    13A Front recoil spring retainer 214721
    13B Snap ring 929191
    14 Buffer spring retainer 214208
    15Buffer spring 214822
    16 Rear recoil spring retainer 214206
    17Guide rod, incomplete 214830
    17Recoil/ buffer spring assembly
    complete 214829
    18 Roll pin,
    ISO 8748 - 3.5 X 10mm929908
    (buffer spring retainer)
    19 Slide release 21418120 Trigger bar,complete214176
    21 Trigger bar detent 214165
    22 Trigger bar detent spring 214166
    23Disconnector 214840
    24 Sear axle 214101
    25Catch 214773
    25AControl latch 214817
    26 Detent plate (variant 1 & 2)214099
    Detent plate** (variant 3 & 4)214254
    Detent plate** (v.5,6,9,& 10)214255
    27 Shaped spring (slide release)214171
    28 Flat spring 214167
    29Hammer, complete
    (variant 1-4, 9 & 10) 214825
    30 Hammer,bobbed (v.5, 6, 7)** 214256
    Hammer, bobbed complete**214744
    (v.5, 6, 7)
    31 Cyl. pin,
    ISO 6325 2.5x8mm971598
    (hammer strut pin)
    32 Hammer axle (v.1-6, 9,10)214774
    Hammer axle** (variant 7)214258
    33 Control lever(variant 1, 5, 9)214184
    Control lever (variant 2, 6, 10)214309
    Control lever(variant 3)214352
    Control lever (variant 4)214253
    34 Sear (variant 1-4, 9, 10)214180
    Sear, complete** 214179
    34A Tube (variant 5, 6, 7)** 214413
    35 Roll pin,
    ISO 8748 - 2 X 10mm982785
    (sear, variant 1, 2, 3, 4, 9, 10)36 Detent slide 
    (variant 1-6, 9, 10)214105
    37 Compression spring, 214104
    (detent slide) variant 1-6, 9, 10
    38Frame, complete 214816
    Frame, incomplete 214675
    39 Trigger rebound spring 214164
    40 Trigger axle 214154
    41Trigger 214841
    42Magazine release 214818
    43 Magazine release spring 214170
    44Hammer strut 214819
    45 Hammer spring 214300
    46Lanyard loop insert 214836
    47 Lanyard loop insert pin 214314
    48Magazine Follower 214832
    49Magazine spring (12-rd)  214833
    Magazine spring (10-rd) **214850
    50Magazine floorplate (12-rd)  214834
    Magazine floorplate (10 rd) 214852
    51Locking plate (12-rd)  214835
    Locking insert (10-rd) **214853
    52Magazine housing (12-rd)  214869
    Magazine housing (10-rd) **214851
    Magazine complete (10-rd) **214868
    Magazine complete (12-rd) **214862
    Mag. extended floorplate (10-rd) **215954
    Mag. extended floorplate (12-rd) **217710
    **Not pictured in diagram
    USP .45 Parts List (Parts exclusive to the USP45 shown in italics)  
    						
    							48
    SECTION 9   USP TACTICAL
    The HK USP Tactical pistol has all of the features found on
    the standard USP45 with the addition of the following:
    • adjustable trigger stop
    • rear sight with micro-meter adjustment for windage
    and elevation
    • high profile front sight
    • extended threaded barrel with O-ring
    • extended foorplate on magazine 
    • loaded chamber indicator
    Adjustable trigger stop
    The trigger stop for the USP Tactical pistol is located on the
    trigger and limits the trigger travel immediately after the
    hammer has been released. It is adjusted by use of the 1.5
    mm allen wrench equipped with the pistol.
    By turning the 1.5 mm set screw clockwise, the overtravel
    of the trigger can be reduced. Care must be exercised in
    making this adjustment as the screw can be adjusted far
    enough to prevent the proper operation of the double
    action and single action trigger.Rear sight
    The USP Tactical uses a micrometer rear target sight which
    is adjustable for windage and elevation. Using an appropriate
    screw driver, the rear sight can be precisely adjusted to align
    with the point of impact.
    Adjusting the elevation
    Rotate the elevation adjusting screw on the top of the rear
    sight in the desired direction with the screwdriver supplied
    with the pistol; rotating it clockwise lowers the point of
    impact approximately 1 cm (0.39 inch) per click at a range
    of 25 meters (27.3 yards), rotating counterclockwise raises
    it the same amount per click.
    Adjusting the windage
    Rotate the windage adjusting screw located on the right
    side of the rear sight in the desired direction with the
    screwdriver supplied with the pistol. Rotating clockwise
    moves the shot to the right. Rotating counterclockwise
    moves the shot to the left. Each click shifts the point of
    impact approximately .5 cm (0.2 inch) to the left or the
    right at a range of 25 meters (27.3 yards). 
    						
    							High profile front sight
    The high profile front sight is mounted on the slide in a
    dovetail and does not require adjustment. It allows the
    operator to obtain a normal sight  picture when an optional
    sound suppressor is mounted.
    Extended barrel with O-ring and muzzle threads
    The 128.5 mm (5.06 inches) hammer forged polygonal
    barrel is engineered for a high level of accuracy. The high
    temperature rubber O-ring located towards the muzzle
    holds the barrel tightly in the slide during firing and
    enhances accuracy. The left hand threads used on the barrel
    of the USP Tactical pistol will accept only those accessories
    designed for the pistol. The MK23 sound suppressor cannot
    be attached to the USP45 Tactical pistol!  A specially
    designed sound suppressor is available for the USP45
    Tactical pistol.
    CAUTION: When used with a suppressor, use only
    HK approved suppressors as currently made by
    Knight’s Armament Company or Brügger & Thomet
    of Switzerland. Even though all types of high velocity
    supersonic (+P) ammunition  can be fired, for
    maximum effectiveness (suppression) only subsonic
    ball ammunition should be used when a sound
    suppressor is attached.
    49
    Place a drop of lubricant on the barrel O-ring during cleaning
    and replace it by hand if/when necessary. Spare O-rings are
    provided with each new USP Tactical pistol. Prolonged use of
    +P ammunition through the pistol with the sound suppressor
    attached is not recommended. Assembly and disassembly of
    the slide, barrel, and frame on the USP Tactical is the same as
    other full-frame USP pistols (see pages 28-33 in this manual).
    Extended foorplate magazine
    The USP Tactical pistol uses magazines with extended
    floorplates; providing a larger, and for many shooters, a
    more comfortable gripping area. It also protects the
    magazine if dropped and assists in the manual removal of
    the magazine in the event a stoppage occurs. This floorplate
    is removed and installed like the standard floorplate (see
    pages 34-37 in this manual). The use of an extended
    floorplate does not affect the magazine capacity.
    Loaded chamber indicator
    The extractor of the USP Tactical pistol doubles as a loaded
    chamber indicator anytime a live cartridge or empty case is
    present in the chamber. A red painted portion of the extractor,
    or its protruding tactile feel, indicates the chamber is loaded.
    Tools provided with the USP Tactical include a 1.5 mm allen
    wrench for adjusting the trigger stop and a screwdriver for
    adjusting windage and elevation on the rear sight. 
    						
    							217705 Slide, USP45 Tactical, incomplete.
    217704 Slide, USP45 Tactical, complete
    986844 Sight, rear adjustable, complete.
    987505 Screwdriver for adjustable rear sight
    50
    Extended foorplate
    on magazine Trigger stop
    (adjust set screw with 
    1.5 mm allen wrench) Front target sight
    Threaded barrel
    with O-ring
    Windage adjustment
    screw Elevation adjustment screw (on top of sight)
    Adjustable trigger
    215939 Sight, front, for use with adjustable rear
    sight
    215864 Extractor with red chamber indicator
    215801 Plug for extractor spring
    217702 Barrel, USP45 Tactical, w/ left hand
    threads, w/o O-ring
    986429 O-ring
    217706 Assembly, captured recoil/buffer spring,
    complete
    217707 Rod, recoil spring guide (bare)
    217703 Frame, complete., USP45 Tactical
    214825 Hammer, with rubber spur,
    complete, USP45  
    217710 Magazine, 12-round, USP45 with LE 
    markings 
    215968 Plate, magazine floor, extended, for 
    USP45 
    215684 Trigger with adjustable trigger stop,
    USP45 Tactical 
    215680 Stop, adjustable trigger, USP45 Tactical 
    958179 Wrench, hex, 1.5mm for adjustable 
    trigger stop USP45 Match
    214300 Spring, hammer                       Part No. Item Description
    Part No. Item DescriptionPart No. Item Description
    Figure 50
    USP  Tactical .45ACP  
    						
    All Heckler and Koch manuals Comments (0)

    Related Manuals for Heckler And Koch HK USP Tactical, USP Expert Operators Manual