Home > Heckler and Koch > Firearms > Heckler And Koch HK UMP45, UMP40 Operators Manual

Heckler And Koch HK UMP45, UMP40 Operators Manual

Here you can view all the pages of manual Heckler And Koch HK UMP45, UMP40 Operators Manual. The Heckler and Koch manuals for Firearms are available online for free. You can easily download all the documents as PDF.

Page 41

41
CARRYING SLING
Carrying sling 
The carrying sling enables the UMP to be carried in several ways. In this
process, the buttstock may be folded up or unfolded. 
The carrying sling is attached to the mounting points on the receiver,
handstop, or buttstock via the carbine hooks.
Length Adjustment 
•  Close coupler 
•  Rest the carrying sling between thumb and index finger and let the
UMP hang down in a horizontal position. Adjust the length in such a
way that there is a space of approximately 10 cm (4...

Page 42

42
UMP SUBMACHINE GUN
Fig. 34 Length adjustment   
Fig. 35 Place upper half onto shoulder over the head 

Page 43

43
CARRYING SLING
Carrying modes 
Fig. 36  UMP across the chest
Fig. 37  UMP on the back    

Page 44

44
UMP SUBMACHINE GUN
Firing positions 
Fig. 38  UMP fired from the shoulder
Fig. 39 UMP fired from the hip 

Page 45

45
SIGHT ALIGNMENT FOR THE UMP
Sight Adjustment 
If the point of impact has to be corrected, this will be done by adjustment
of the rear sight using the Allen wrench provided with the weapon.
The UMP is zeroed at the factory to hit the point of aim at 25 meters 
(27.3 yards).
Elevation adjustment 
•  To lower the weapon’s point of impact, turn the elevation adjustment
screw clockwise.
•  To raise the weapon’s point of impact, turn the elevation adjustment
screw counterclockwise.
NOTE: 1 revolution of the...

Page 46

46
UMP SUBMACHINE GUN
Correct point of aim
Even circle of light
Sight alignment for  UMP
Fig. 42    Sight pictures
Point of aim
Rear sight
Aperture
Circle of light
Front sight holder
Front sight post
Impact as with incorrectly
centered front sight = right
Impact as with full sight
= highImpact as with fine sight
= lowImpact as with incorrectly
centered front sight = left 

Page 47

47
SPECIFICATIONS
Specifications UMP45
Caliber  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 ACP
Operating principle  . . . . . . . . . . . . . . . . . . . . . . . . . .Simple blow back, firing from a closed bolt position
Dimensions
Overall length, buttstock extended  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690 mm (27.17 in)
Overall length, with sound suppressor, buttstock extended...

Page 48

48
UMP SUBMACHINE GUN
Upper receiver with barrel,complete (I - 21) 217503
1 Upper receiver, incomplete 217509
2 Front sight 217506
3 Roll pin, front sight, 4x 144 mm 928747
Rear sight, complete. (4 - 10) 217513
4 Sight support 217992
5 Flat spring 217515
6 Rear sight 217516
7 Windage adjustment screw 217517
8 Rear sight spring 217518
9 Sight support spring 217504
10 Elevation adjustment screw 217505
11 Roll pin, sight support 987695
12 Cocking lever 217519
13 Cocking lever spring 217508
14 Cocking lever...

Page 49

49
EXPLODED DIAGRAM & PARTS LIST
Item Description Part No. Item Description Part No.
NOTE: UMP .40 S&W parts are
shown in italics in parts lists
37 Sear 205439
38 Sear spring 205421
39 Release lever 217535
40 Release lever spring 217534
41 Hammer 217545
42 Hammer spring, left 217533
43 Hammer spring, right 217585
44 Notched disk 205417
45 Compression spring 205418
46 Index plate 205419
47 Slide 214608
48 Safety lever, left 217753
49 Safety lever, right 214607
50 Magazine release 217537
51 Magazine...
Start reading Heckler And Koch HK UMP45, UMP40 Operators Manual

Related Manuals for Heckler And Koch HK UMP45, UMP40 Operators Manual

All Heckler and Koch manuals