Hanns G Hp222dgb Users Manual

							
 
 
 
 
 
HP222 
HSG 1095 
 
						

							
User’s Manual 
 
Before operating the monitor, please read this manual thoroughly. This manual should be retained for 
future reference. 
 
 
FCC Class B Radio Frequency Interference Statement   
 
This equipment has been tested and found to comp ly with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits  are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy, and if not installed  and used in accordance with the instructions, may 
cause harmful interference to radio communications. Ho wever, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cau se harmful interference to radio 
or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct  the interference by one or more of the following measures: 
ƒ  Reorient or relocate the receiving antenna. 
ƒ  Increase the separation between  the equipment and receiver. 
ƒ  Connect the equipment into an outlet on a circuit  different from that to which the receiver is 
connected. 
ƒ   Consult the dealer or an experien ced radio/TV technician for help. 
 
The device complies with Parts 15 of the FCC Ru le. Operation is subject to the following two 
conditions ﹕(1) this device may not cau se harmful interference﹔and (2) this device must accept any 
interference received, including interference  that may cause undesired operations. 
 
CANADA 
This Class B digital apparatus meets all requi rements of the Canadian Interference-Causing 
Equipment Regulation.   
 
 
 
This device complies with requirement of EMC directive 2004/108/EC with regard to 
Electromagnetic Compatibility, and 73/23/EEC and 93/ 68/EEC with regard to Low Voltage directive. 
 
 
Socket-outlet shall be near the equipment and shall be accessible. 
 
2 
 
						

							
                                                                    User’s Manual  
 
 
 
Congratulations! 
The display you have just purchased carries the TCO’03 Displays label. 
This means that your display is de signed, manufactured and tested 
according to some of the stri ctest quality and environmental 
requirements in the world. This makes for a high performance product, 
designed with the user in focus that also minimizes the impact on our 
natural environment. 
 
Some of the features of the TCO’03 Display requirements: 
 
Ergonomics 
• Good visual ergonomics and image quality in orde r to improve the working environment for the 
user and to reduce sight and st rain problems. Important parame ters are luminance, contrast, 
resolution, reflectance, colour  rendition and image stability. 
 
Energy 
• Energy-saving mode after a certain time – benefi cial both for the user and the environment 
• Electrical safety 
 
Emissions 
• Electromagnetic fields 
• Noise emissions 
 
Ecology 
•  The product must be prepared for recycling  and the manufacturer must have a certified 
environmental management system such as EMAS or ISO 14 001 
•   Restrictions on 
{ chlorinated and brominated flame retardants and polymers 
{ heavy metals such as cadmium, mercury and lead. 
 
The requirements included in this label have be en developed by TCO Development in cooperation 
with scientists, experts, users as well as manufacturers all over the world. Sin ce the end of the 1980s 
TCO has been involved in influencing the developm ent of IT equipment in a more user-friendly 
direction. Our labelling system started with displa ys in 1992 and is now requested by users and 
IT-manufacturers all over the world. 
 
For more information, please visit 
www.tcodevelopment.com 
 
 
 
 
 
 
3 
 
						

							
User’s Manual 
 
RECYCLING INFORMATION 
 
We, the Hanns.G care very much about our environment prot ection strategy and firmly believe that 
it helps us have healthier earth via appropriate treatment and  recycling of industrial technology 
devices at the end-of-life. 
These devices contain recyclable materials, whic h can be re-decomposed and re-integrated into 
brand-new marvels. On the contrary, other materi al can be classified to hazardous and poisoned 
substances. We strongly encourage  you to contact the provided information to recycle this product. 
 
For more information, please visit 
www.hannsg.com 
 
 
4 
 
						

							
                                                                    User’s Manual  
TABLE OF CONTENTS 
 
SAFETY NOTICE........................................................................\
.......................... 6 
PRECAUTIONS........................................................................\
......................... 6 
SPECIAL NOTES ON LCD MONITORS ...................................................... 7 
BEFORE YOU OPERATE THE MONITOR ...................................................... 8 
FEATURES........................................................................\
................................. 8 
CHECKING THE CONTENTS OF THE PACKAGE .................................. 8 
ADJUSTING DISPLAY HEIGHT................................................................... 9 
INSTALLATION INSTRUCTIONS .............................................................. 10 
POWER........................................................................\
..................................... 10 
SETTING THE MONITOR ON THE WALL ...............................................11 
MAKING CONNECTIONS........................................................................\
.... 12 
ADJUSTING THE VIEWING ANGLE ......................................................... 13 
OPERATING INSTRUCTIONS........................................................................\
. 14 
GENERAL INSTRUCTIONS........................................................................\
. 14 
FRONT PANEL CONTROL........................................................................\
.. 15 
HOW TO ADJUST A SETTINGS .................................................................. 17 
PLUG AND  PLAY........................................................................\
.................... 20 
TECHNICAL SUPPORT (FAQ) ........................................................................\
. 21 
Q & A FOR GENERAL PROBLEMS ........................................................... 21 
ERROR MESSAGE & POSSIBLE SOLUTIONS ....................................... 23 
APPENDIX........................................................................\
.................................... 25 
SPECIFICATIONS ........................................................................\
.................. 25 
 
5 
 
						

							
User’s Manual 
 
SAFETY NOTICE 
 
1. The changes or modifications  not expressly approved by the pa rty responsible for compliance 
could void the users authority  to operate the equipment. 
2. Shielded interface cables and AC pow er cord, if any, must be used in order to comply with the 
emission limits. 
3.  The manufacturer is not respons ible for any radio or TV interference caused by unauthorized 
modification to this equipment. It is the responsibilities of the user to co rrect such interference. 
 
WARNING: 
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high 
voltages are present inside the monitor. Do not open the cabinet. Refer  servicing to qualified 
personnel only.  
 
PRECAUTIONS 
• Do not use the monitor near water, e.g. near  a bathtub, washbowl, kitchen sink, laundry tub, 
swimming pool or in a wet basement. 
•  Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a  person and cause serious damage to the applianc e. Use only a cart or stand recommended by the 
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a 
mounting kit approved by the manufacturer and follow the kit instructions. 
•  Slots and openings in the back and bottom of th e cabinet are provided for ventilation. To ensure 
reliable operation of the monitor  and to protect it from overheating, be sure these openings are not 
blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place 
the monitor near or over a radiator or heat re gister. Do not place the monitor in a bookcase or 
cabinet unless proper ventilation is provided. 
•  The monitor should be operated only from the t ype of power source indicated on the label. If you 
are not sure of the type of power supplied to  your home, consult your dealer or local power 
company. 
•  Unplug the unit during a lighting storm or when it  will not be used for long period of time. This 
will protect the monitor from damage due to power surges. 
•  Do not overload power strips and extension cords.  Overloading can result in fire or electric shock. 
•  Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a 
fire or electric shock. Never  spill liquids on the monitor. 
•  Do not attempt to service the monitor by yourse lf; opening or removing covers can expose you to 
dangerous voltages and other haza rds. Please refer all servicing to qualified service personnel. 
•    The wall socket shall be in stalled near the equipment and shall be easily accessible. 
 
6 
 
						

							
                                                                    User’s Manual  
SPECIAL NOTES ON LCD MONITORS 
 
The following symptoms are normal with LCD monitor and do not indicate a problem. 
 
•  Due to the nature of the fluorescent light, the sc reen may flicker during initial use. Turn off the 
Power Switch and then turn it on again to make sure the flicker disappears. 
•  You may find slightly uneven brightness on the  screen depending on the desktop pattern you use. 
•  The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or 
less such as a missing pixel or  a pixel lit all of the time. 
•  Due to the nature of the LCD screen, an afteri mage of the previous screen may remain after 
switching the image, when the same image is disp layed for hours. In this case, the screen is 
recovered slowly by changing the image or  turning off the Power Switch for hours. 
•  If the screen suddenly flashes erratically or the backlighting fa ils, please contact your dealer or 
service center for repair. Do not atte mpt to repair the monitor yourself. 
 
Lamp Disposal 
 
 
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR 
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE 
INFORMATION, CONTACT THE ELECTR ONIC INDUSTRIES ALLIANCE AT 
WWW.EIAE.ORG. 
FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK 
WWW.LAMPRECYCLE.ORG. 
 
7 
 
						

							
User’s Manual 
 
BEFORE YOU OPERATE THE MONITOR 
 
FEATURES 
 
•  22” Wide screen TFT Color LCD Monitor 
•  Crisp, Clear Display for Windows 
• Recommended Resolutions: 1680 X 1050 @60Hz 
•  EPA ENERGY STAR® 
•  GP Green Product 
• Ergonomic Design 
•  Space Saving, Compact Case Design 
 
CHECKING THE CONTENTS OF THE PACKAGE 
   
The product package should include the following items: 
LCD Monitor 
 
Cables and User manual 
    
Power Cord Warranty Card Quick Start Guide User’s Manual 
   
Audio Cable (optional) VGA Cable DVI Cable (optional) 
 
8 
 
						

							
                                                                    User’s Manual  
ADJUSTING DISPLAY HEIGHT 
1. In order to achieve the best visual effects, it is recommended that  the display be adjusted so that 
the entire screen is facing you before you adjust  the display height according to your personal 
preference.  
2.  Hold the top edge of the display (fig. A) and re move the pin from the rear of the display stand 
(fig. B) to adjust it to  appropriate height (fig. C). 
 
Note 
y  Be sure not to exert pressure on the LCD while  adjusting the height to prevent damaging or 
cracking the screen.   
y   When adjusting the display height, be sure to place the stand upright on a flat surface (such as a 
table) prior to adjustment. Do not place the LC D monitor on top of the table or remove the pin 
while the stand is inverted (fig. D). Keep your fi ngers or hands away from the height adjustment 
mechanism (fig. E) to prevent injury. 
 
 
 
 
9 
 
						

							
User’s Manual 
 
INSTALLATION INSTRUCTIONS 
 
INSTALL  &  REMOVE 
 
 
 
Figure.1. Installing and Removing the Base 
 
 
 
 
 
 
 
 
 
 
 
 
 
POWER 
 
POWER SOURCE: 
 
1. Make sure that the power cord is the correct type required in your area. 
2. This LCD monitor has an Internal  universal power supply that allows operation in either     
100/120V AC or 220/240V AC voltage area  (No user adjustment is required.) 
3. Connect the AC-power cord one end to your LC D monitor’s AC-input socket, the other end to 
wall-outlet.  
10