Hanns G Hi221ap Users Manual

							User’s Manual  
11 
ADJUSTING THE VIEWING ANGLE 
 
•  For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the 
monitor’s angle to your own preference. 
•  Hold the stand so you do not topple the monitor when you change the monitor’s angle. 
•  The monitor’s angle is adjustable from -5° to 20°. 
 
 
 
Figure.3. Monitor Angle 
 
NOTES:
 
 
•  Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD 
screen. 
• 
Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise 
pinching can result. 
 
 
 
 
 
 
 
						

							User’s Manual 
 
12 
OPERATING INSTRUCTIONS 
 
GENERAL INSTRUCTIONS   
   
Press the power button to turn the monitor on or off. The other control buttons are located on the 
front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to 
your personal preference. 
 
•  The power cord should be connected. 
•  Connect the Signal cable from the monitor to the VGA card. 
•  Press the power button to turn on the monitor. The power indicator will light up. 
 
 
Figure.4. Control Panel Buttons 
 
CONTROL PANEL BUTTONS: 
 
1. Menu / Return 2. Input source change / Enter 
3. Brightness adjustment button /< [-] 4. Volume adjustment button / > [+] 
5. Power Button 6. Power Indicator 
 
 
						

							User’s Manual  
13 
FRONT PANEL CONTROL 
 
• Power Button: 
Press this button to switch ON/OFF monitor’s power. 
 
• Power Indicator: 
Green — Power On mode. 
Orange — Power Saving mode. 
 
•  MENU / RETURN:   
1. Turn the OSD menu on/off or return to the previous menu. 
2. Exit OSD menu when in volume OSD status. 
 
• Adjust < >:  
1. Adjust Brightness and volume when the OSD is off. 
2. Navigate through adjustment icons when OSD is ON or adjust a function when function is 
activated. 
 
• AUTO Button:  
  1. Press the AUTO button to select the input signal type. (There are VGA, DVI options available 
but what port you can actually select depends on your model.) 
2. The OSD menu is used as “confirmation” function during start-up. 
3. Press and hold this button more than 3 seconds will start 「Auto Adjust」  function when using 
VGA input only. (The auto adjustment function is used to optimize the 「horizontal position」, 
「vertical position」,「clock」,and 「phase」.) 
   
 
NOTES:
 
 
•  Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a 
place subject to direct sunlight, or excessive dust or mechanical vibration or shock. 
•  Save the original shipping box and packing materials, as they will come in handy if you ever have 
to ship your monitor. 
•  For maximum protection, repackage your monitor as it was originally packed at the factory. 
•  To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be 
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents 
such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety 
precaution, always unplug the monitor before cleaning it. 
 
						

							User’s Manual 
 
14 
HOW TO ADJUST A SETTINGS 
 
BRIGHTNESS/CONTRAST 
BRIGHTNESS 
Adjust the brightness value of the display according to your 
preference. Select「BRIGHTNESS」option to adjust the 
brightness value. 
CONTRAST 
Adjust the contrast value of the display according to your 
preference. Select「CONTRAST」option to adjust the contrast 
value. 
X-CONTRAST 
Optimal setting for high contrast images or videos. The dark and 
light areas of the image are automatically detected, and the 
contrast is enhanced to provide a clearer, sharper image. Also, 
you may select the「X-CONTRAST」option. 
INPUT SETTING 
INPUT SETTING 
Select the 「INPUT SETTING」option to change between analog 
(VGA) or Digital (DVI) source. Enter the option and select 
Analog or Digital. [Dual input mode optional] 
AUTO SEARCH 
From the Signal Selection menu, select the 「AUTO SEARCH」
option to activate or deactivate the automatic signal search 
function. [For DVI Input only] 
COLOR SETTING 
WA R M  
NATURE 
COOL 
Adjust the color temperature value of the display according to 
your preference: WARM /NATURE/ COOL. 
USER 
Move the cursor to the User option and select it,   
To adjust the red, enter the「R」option and adjust the level. 
To adjust the green, enter the「G」option and adjust the level. 
To adjust the blue, enter the「B」option and adjust the level. 
IMAGE SETTING 
AUTO ADJUST 
The auto adjustment function is used to optimize the 「horizontal 
position」, 「vertical position」,「clock」,and 「phase」. [For 
VGA Input only] 
ASPECT RATIO 
When the aspect ratio of screen is distorted, you may make 
adjustments by using this function. “FULL” indicates full screen 
display, which does not ensure the image is shown as is or in 
initial scale. “FIT” indicates scaling by the proportion of original 
images, which may cause the screen showing black bands. [The 
availability of this function depends upon the selected model] 
 
						

							User’s Manual  
15 
H-POSITION 
Select the 「H-POSITION」option to shift the screen image to the 
left or right. Enter the option and adjust the level. [For VGA 
only] 
V-POSITION Select the 「V-POSITION」option to shift the screen image up or 
down. Enter the option and adjust the level. [For VGA only] 
CLOCK  
Select the 「CLOCK」option to reduce the vertical flicker of 
characters on the screen. Enter the option and adjust the level. 
[For VGA only] 
PHASE  
Select the「PHASE」option to reduce the horizontal flicker of 
characters on the screen. Enter the option and adjust the level. 
[For VGA only] 
SHARPNESS Select the「SHARPNESS」option to adjust the sharpness of the 
display. Set the value from -2 to 2. 
OSD SETTING 
LANGUAGE 
Select 「LANGUAGE」  option to change the language of the 
OSD. Enter the option and select a language. [Reference only, 
the OSD Language depends on the selected model] 
H-POSITION Select 「H-POSITION」option to adjust the horizontal position of 
the OSD. Enter the option and adjust the level. 
V-POSITION Select 「V-POSITION」option to adjust the vertical position of 
the OSD. Enter the option and adjust the level. 
TRANSPARENCY Select 「TRANSPARENCY」option to adjust the transparency of 
the OSD. Enter the option and adjust the level.   
OSD TIME-OUT Select 「OSD TIME-OUT」option to set the OSD time out from 
10 to 100 seconds. Enter the option and adjust the level. 
OSD COLOR 
To choose the color combination of the OSD window, select 
「OSD COLOR」option under 「OSD SETTING」menu, choose 
modes 1/2/3. 
SYSTEM 
VOLUME  Select the 「VOLUME」option to change the volume level. Enter 
the option and adjust the level. 
MUTE Select the「MUTE」option to switch the function On or Off. 
DDC/CI Select the 「DDC/CI」option to switch the function On or Off. 
[Dual input mode optional] 
 
						

							User’s Manual 
 
16 
FACTORY RESET 
Select the 「FACTORY RESET」option to reset to the monitor’s 
default setting. This will erase the current settings. Enter the 
option and select On or Off. 
INFORMATION Display Horizontal frequency/Vertical frequency/Resolution 
information.  
   
   
   
   
   
   
 
 
 
						

							User’s Manual  
17 
PLUG AND  PLAY   
 
Plug & Play DDC2B Feature 
 
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. 
It allows the monitor to inform the host system of its identity and, depending on the level of DDC 
used, communicate additional information about its display capabilities. The DDC2B is a 
bidirectional data channel based on the I²C protocol. The host can request EDID information over the 
DDC2B channel. 
 
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO 
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE 
MUST BE A VIDEO INPUT SIGNAL. 
 
This monitor meets the Green monitor standards as set by the Video Electronics Standards 
Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The 
Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy 
by reducing power consumption when there is no video-input signal present. When there is no video 
input signal this monitor, following a time-out period, will automatically switch to power saving 
mode. This reduces the monitors internal power supply consumption. After the video input signal is 
restored, full power is restored and the display is automatically redrawn. The appearance is similar to 
a Screen Saver feature except the display is completely off. The display is restored by pressing a 
key on the keyboard, or clicking the mouse. 
 
						

							User’s Manual 
 
18 
TECHNICAL SUPPORT (FAQ) 
Q & A FOR GENERAL PROBLEMS 
PROBLEM & QUESTION POSSIBLE SOLUTION 
Power LED is not on *Check if the Power Switch is in the ON position. 
*Power Cord should be connected. 
No Plug & Play 
*Check if the PC system is Plug & Play compatible. 
*Check if the Video Card is Plug & Play compatible. 
*Check if any plug pins on the VGA or DVI connector are 
bent. 
The display is too dark or too 
bright. *Adjust the Contrast and Brightness Controls. 
Picture bounces or a wave 
pattern is present in the picture 
*Move electrical devices that may cause electrical 
interference. 
The power LED is ON (orange) 
but there’s no video or no 
picture. 
*Computer Power Switch should be in the ON position. 
*Computer Video Card should be snugly seated in its slot. 
*Make sure monitor’s video cable is properly connected to the 
computer. 
*Inspect monitor’s video cable and make sure none of the pins 
are bent. 
*Make sure computer is operational by hitting the CAPS 
LOCK key on the keyboard while observing the CAPS 
LOCK LED. The LED should either turn ON or OFF after 
hitting the CAPS LOCK key. 
Missing one of the primary 
colors (RED, GREEN, or 
BLUE) 
*Inspect the monitor’s video cable and make sure that none of 
the pins are bent. 
Screen image is not centered or 
sized properly. 
* Adjust pixel frequency CLOCK and PHASE or press hot-key 
(AUTO Button) 
Picture has color defects 
(white does not look white) *Adjust RGB color or select color temperature. 
The screen resolution needs to 
be adjusted 
*Use win 2000/ME/XP Right click anywhere on desktop and 
select Properties>Settings>Screen Resolution. Use the 
silder to adjust the reslution and click Apply. 
No sound is outputted from 
monitor’s built-in speaker 
*Make sure PC audio output cable is connected to screen＇s 
LINE IN port (or AUDIO IN port). 
*Make sure the sound volume adjustment can be clearly 
identified. 
*Make sure the System > Silence option in the monitor menu 
is on. 
 
						

							User’s Manual  
19 
ERROR MESSAGE & POSSIBLE SOLUTIONS 
 
ƒ CABLE NOT CONNECTED: 
1. Check that the signal-cable is properly connected, If the connector is loose, tighten the 
connector’s screws. 
2. Check the signal-cable’s connection pins for damage. 
 
ƒ INPUT NOT SUPPORT: 
Your computer has been set to unsuitable display mode, set the computer to display mode given 
in the following table.   
 
RECOMMENDED AND SUPPORTED TIMING MODE:
 
 
MODE
 RESOLUTION HORIZONTAL 
FREQUENCY (KHz)
VERTICAL 
FREQUENCY (Hz) 
1 640×350 @70Hz VGA 31.469 70.087 
2 640×400 @56Hz PC9801 24.827 56.424 
3 640×400@70HzVGATEXT 31.469 70.087 
4 640×480 @60Hz VGA 31.469 59.94 
5 640×480 @67Hz MAC 35 66.667 
6 640×480 @70Hz VGA 36.052 70.004 
7 640×480 @72Hz VGA 37.861 72.809 
8 640×480 @75Hz VGA 37.5 75 
9 720×400@70HzVGATEXT 31.469 70.087 
10 720x480@60Hz VGA 31.469 59.94 
11 800×600 @56Hz SVGA 35.156 56.25 
12 800×600 @60Hz SVGA 37.879 60.317 
13 800×600 @72Hz SVGA 48.077 72.188 
14 800×600 @75Hz SVGA 46.875 75 
15 832×624 @74.6Hz MAC 49.725 74.5 
16 1024×768 @60Hz XGA 48.363 60.004 
17 1024×768 @66Hz XGA 53.964 66.132 
18 1024×768 @70Hz XGA 56.476 70.069 
19 1024×768 @75Hz XGA 60.023 75.029 
20 1024×768 @75Hz MAC 60.15 74.72 
21 1152×864 @75Hz SXGA 67.5 75 
22 1152×870 @75Hz MAC 68.681 75.062 
23 1152×900 @66Hz SUN66 61.846 66.004 
24 1280×720 @60Hz 45 60 
25 1280×768 @60Hz 47.776 59.87 
26 1280×768 @75Hz 60.289 74.893 
27 1280×960 @60Hz 60 60 
28 1280×960 @75Hz 74.592 74.443 
 
						

							User’s Manual 
 
20 
29 1280×1024 @60Hz SXGA 63.981 60.02 
30 1280×1024 @72Hz SXGA 76.02 71.448 
31 1280×1024 @75Hz SXGA 79.976 75.025 
32 1360×768 @60Hz SXGA 47.712 60.015 
33 1400×1050@60Hz WXGA + 64.744 59.948 
34 1400×1050@60Hz WXGA + 65.317 59.978 
34 1400×1050@75Hz WXGA + 82.278 74.867 
35 1440×900 @60Hz SXGA 55.469 59.901 
36 1440×900 @60Hz SXGA 55.935 59.887 
37 1440×900 @75Hz SXGA 70.635 74.984 
38 1600×1200@60Hz 75 60 
39 1600×1200@65Hz 81.25 65 
40 1680×1050@60Hz 64.674 59.883 
41 1680×1050@75Hz 82.306 74.892 
 
We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee the 
image quality.