Haier Hdy60m 6kg Manual

							WALL  MOUNTING INSTRUCTIONS
1. Determine the location of the dr yer on the wall and mark the 
    bracket position. A minimum 50 mm is needed be tween the top of the dryer and
   the celling for ease of installation;
   If mounting above a washing ma chine, allow sufficient room to
   open the lid of the washe r.
9
Tools required:
For plaster/          Drill&3mm Bit                        1
Wooden wall       Philips head screwdriver       1 
Wall mounting kit includes 

Plastic Spacers                     2
Wall hanging brackets          2
Hanging hook                       2
Wood screws, 12gx50mm    4
Screws for hanging hooks     6
and plastic spacers.
Description
2. Fix the wall hanging brackets to the wall securely (eg. into the stu\
d).
    If the studs a re too far apart, fit a timber slat to the studs then mount the
   brackets onto the slat. The distance between each is 553 mm as per
   diagram.
Wood screw
553 mm
The dryer can be mounted on the wall in the inverted position only by 
following these instructions. Invert the dryer so that the control panel 
is at the bottom (see figure 3) this allows easier access to the contr\
ols. 
						

							
WALL MOUNTING INSTRUCTIONS
3. Install the hooks to the dryer, in the inverted position, remove 
    the 2 screws and 2 plastic plugs as indicated in Fig.1 .
4. Align the hooks as shown in Fig.2 and refit screws tightly.
    Install the spacers provided as Fig.2. 
10
plastic plugs
2 hooks
3 screws
2 spacers 
						

							WALL  MOUNTING INSTRUCTIONS
5. W ith assistance, mount dryer on  wall bracket s. See Fig. 3
6.  Asecond control panel with inverted symbols is supplied.
Peel the release paper from the back of inverted film then 
place new control panel film on t he surface so that the writing is the 
    correct way around.
1 1
Caution:
     Plug must be accessble after installation.
Start
HDY -M 60OFF
20 min
60 min
100 min
150 min
200 min
OFF 60 min
30 min
Cool
Warm
HDY -M60
StartCool
Warm
OFF
20 min
60 min
100 min
150 min
200 min
OFF
60 min 30 min 
						

							DRYING RACK FITTING INSTRUCTION
DRYER FREE ST ANDING-UPRIGHT
For ease of access, the rack is to be mounted near the dryer top. Firstl\
 y hold the rack 
horizontally with the two end projections point ing upwards and away from yourself. 
Position the rack near the top of the dryer 
and place the end of the right rack projection 
into the right cabinet mounting hole (Fig.1).
Then gently pull on the left rack projection un til
it fits around the cabinet and springs into the
left cabinet mounting hole.
The rack will now lie horizontall y, supported
by the cabinet. Rotate the door outlet grills
that the air exausts upwards and through the
rack.
RACK ST ORAGE - DR YER UPRIGHT
When the drying rack is not needed, simply p ivot the rack upwards untill it lies flat on the top 
of your dryer .
WALL  MOUNTED - DR YER INVERTED
In this situation, the rack is to be mounted near  the dryer door part way along the cabinet.
Firstly hold the rack horizontally with the 
two end projections pointing upwards and
away from yourself.
Position the rack in front of the dryer and
place the end of the right rack projection
into the right cabinet mounting hole ( Fig.2).
Then gently pull on the left rack projection
until it fits around the cabinet and springs
into the left cabinet mounting hole.
The rack will now lie horizontall y, supported
by the cabinet.
Rotate the door outlet grill so that the air exhaust blows upwards and through the rack.
12 
						

							RACK FITTING INSTRUCTION
RACK STORAGE - DR YER INVERTED.
To hold the dryer rack out of the way
when not in use, it will be necessary to
attach the retaining clip to the base of 
your dryer .
T o do this, firstly remove the screw located
4 cm from the right corner of the inverted
dryer ( Fig.3).
Then position the retaining clip over the hole
 so that the prong on the clip is near the
cabinet corner and faces outwards (Fig.4).
LOADING DR YER RACK
To make use of the drying rack, firstly rotate
the outlet grill so that the louvers point towards 
the rack.
Place items to be dried at the centre of the rack
for best airflow .
Shoes should be placed upside down.
A  large woollen article e.g. a cardigan, should
be placed over the whole rack, and to ensure
more even drying will need rearranging from
time to time.
Caution:
1.The maximum weight placed on the dryer r ack should not exceed 1 kg.
2.Make sure the clothes are suitable for the drye r.
3.As the exhause air temperature rises at the end of a normal drying cycle, it
   is important that you regularly check items on the rack to make sure they
  are not overheated.
13
Tighten clip using the same screw. Repeat thi s 
on the left side.
Fit dryer rack to its cabinet mountings. Tilt 
rack upwards and align retaining clip until rac k frame
 “snaps” into the prongs of the retaining clips  (Fig. 4). 
						

							14
The following must be confirmed before calling for service:
Problem                           Possible Cause
The dryer does not start
The drying result is not 
good-Is the dryer plugged in?
-Is the power on?
-Is the door closed properly?
-Has a drying program been set?
-Was the correct drying program set?
-Is the filter screen clean?
-Did the amount of the loaded laundry exceed the rated load?
-Was the loaded laundry spun dry before being  loaded into the dryer?
-Did the laundry become twisted during drying? 
N L
T3
1~
T2
MS
T4
Door Lock
M
4
1
56
Relay
Startup switch Capacitor
Timer
T1
Motor
Thermal cut-outHeater
Thermostat
-Has the Start button been pressed? 
1
Power supply
Maximum operating current (A)
Rated load (kg)
Maximum power (W)
Dimensions (HxDxW) mm Weight (kg) 

220-240)V~/50Hz
106
2100
830 x 560 x 600 30
IPX 4
Waterproof degree
ITEM TYPE
HDY-M60


220-240)V~/50Hz
104
2100
830 x 445 x 600 28
IPX 4
HDY-M40