Haier Gdz51 Manual

							English•Dryer must be exhausted outside (outdoors, not beneath the mobile
home) using metal ducting that will not support combustion. 
Metal ducting must be 4 inches (10.16 cm) in diameter with 
no obstructions. Rigid metal duct is preferred.
•If dryer is exhausted through the floor and  area beneath the
mobile home is enclosed, the exhaust system must terminate 
outside the enclosure with the termination securely fastened to the
mobile home structure.
• Refer to previous pages for other important venting requirements.
•Installation must conform to current Manufactured Home
Construction & Safety Standard (which is a Federal Regulation 
Title 24 CFR-Part 32-80) or when such standard is not applicable,
with American National Standard for Mobile Homes.
Warning:The dryer is designed under ANSI z 21.5.1
for home use only. Installation in Mobile HomeDO
CorrectDON’T
Incorrect
DO
CorrectDON’T
Incorrect20GDZ5-1 manual  10/22/01  11:44 AM  Page 21 
						

							21English
1. This appliance must be properly grounded. Electrical shock can result if the 
dryer is not properly grounded. Follow the instructions in this manual 
for proper grounding.
2. Do not use an extension cord with this dryer. Some extension cords are not
designed to withstand the amounts of electrical current this dryer utilizes and 
can melt, creating electric shock and/or fire hazard. Locate the dryer within
reach of the receptacle for the length power cord to be purchased, 
allowing some slack in the cord. Refer to the electrical requirements 
in this manual for the proper power cord to be purchased.
3. A U.L. approved strain relief must be installed onto power cord. If the strain 
relief is not attached, the cord can be pulled out of the dryer and can be cut 
by any movement of the cord, resulting in electrical shock.
4. Do not use an aluminum wire receptacle with copper wired power 
cord and plug (or vice versa). A chemical reaction occurs between 
copper and aluminum and can cause electrical shorts. The proper wiring 
and receptacle is a copper wired power cord with a copper wired receptacle.
Note:Dryers operating on 208 Volt power supply will have longer 
drying times than operating on 240 Volt power supply.
Danger:Improper connection of the equipment grounding conductor 
can result in a risk of electrical shock. Check with a licensed 
electrician if you are in doubt as to whether the appliance is 
properly grounded. The dryer must be connected to a grounded
metal, permanent wiring system, or an equipment grounding 
conductor must be run with the circuit conductors and connected 
to the equipment-grounding terminal or lead on the appliance.The following are specific requirements for proper and safe
electrical installation of your dryer. Failure to follow these
instructions can create electrical shock and/or fire hazard.WARNINGSElectrical Connections
Requirements and InstructionsGDZ5-1 manual  10/22/01  11:44 AM  Page 22 
						

							English1. Remove the screws securing the terminal block access cover 
and the strain relief mounting bracket located on the back of the 
dryer upper corner.
2. Install a U.L. approved strain relief into the power cord entry hole 
of the mounting bracket. Finger tighten the nut only at this time.
3. Thread a U.L. Approved 30 Amp. Power cord, NEMA 10-30 Type
SRDT, through the strain relief.
4. Attach the power cord neutral (center wire) conductor to the silver 
colored center terminal on the terminal block. 
Tighten the screw securely.
5. Attach the remaining two power cord outer conductors to the 
outer brass colored terminals on the terminal block. Tighten both 
screws securely.Warning:Do not make a sharp bend or crimp
wiring/conductor at connections.
6. Reattach the strain relief mounting bracket to the back of the dryer 
with two screws. Tighten screws securely.
7. Tighten the screws securing the cord restraint firmly against the 
power cord.
8. Tighten the strain relief nut securely so that the strain relief does 
not turn.
9. Reinstall the terminal block cover. 3-Wire Cord Connectionsgreen 
ground 
screwgreen
neutral
ground
wiresilver terminalnuttighten nut
to these threadspower cordstrain relief
mounting bracket22GDZ5-1 manual  10/22/01  11:44 AM  Page 23 
						

							23English
4-Wire Cord Connections1. Remove the screws securing the terminal block access cover 
and the strain relief mounting bracket located on the back 
of the dryer upper corner.
2. Install a U.L. approved strain relief into the power cord entry hole 
of the mounting bracket. Finger tighten the nut only at this time.
3. Remove the green neutral ground wire from the green ground 
screw located above the terminal block.green 
ground 
screw
green neutral
ground wiregreen power cord
ground wiresilver terminalterminal blocktighten nut to
these threadsblack
white
nut
strain relief 
mounting bracket power cordTypical
Conductor
Receptacle
Typical 
4 Conductor 
Cordblack 240V
white neutral
red 240V
green ground
30 AMP NEMA 14-30 TYPE SRDT OR ST redGDZ5-1 manual  10/22/01  11:44 AM  Page 24 
						

							English4.   Thread a U.L. approved 30 Amp power cord, NEMA 14-30 type ST 
or SRDT through the strain relief.
5. Attach the green power cord ground wire to the cabinet with 
green ground screw.
6. Attach the white (neutral) power cord conductor from the power 
cord and the green ground wire from the dryer harness to the 
silver-colored center terminal on the terminal block. Tighten the 
screw securely.
7.   Attach the red and black power cord conductors to the outer 
brass-colored terminals on the terminal block. Warning:Do not
make a sharp bend or crimp wiring/conductor at connections.
8.   Tighten the screws securing the cord restraint firmly against the 
power cord.
9.   Tighten the strain relief nut securely so that the strain relief does 
not turn.
10. Reinstall the terminal block cover.
Caution:Label all wires prior to disconnection, when servicing
controls. Wiring errors can cause improper operations
and be dangerous. Check unit for proper operation
after servicing.
Warning:Discard or destroy the carton and plastic bags after the 
dryer is unpacked. Children should not be allowed to
use them to play with. Cartons covered with rugs, 
bedspreads, or plastic sheets can become an airtight
chamber and cause suffocation leading to death. Make
all packing materials inaccessible to children.
Warning:The instructions in this manual and all other literature
included with this dryer can not cover every possible 
condition and situation that may occur. Good safe
practice and caution must be applied when installing,
operating and maintaining any appliances. After
installing, if you are in doubt, call a certified 
electrician to install and wire the dryer.24GDZ5-1 manual  10/22/01  11:44 AM  Page 25 
						

							25EnglishLimited Warranty
Full ONE Year In-Home Warranty
For 12 months from the date of original retail
purchase, Haier will repair or replace any
part free of charge including labor that fails
due to a defect in materials or workmanship.
Limited Warranty
After one year from the original retail pur-
chase date, Haier will provide a part at no
cost, as indicated below, to replace said part
as a result of a defect in materials or work-
manship. Haier is responsible solely for the
cost of the part. All other costs such as labor,
trip charge, etc are the responsibility of the
owner.
Second Year
Haier will provide All Parts.
Third through Fifth Year
Haier will provide the drive motor or timer.
Haier will provide the dryer drum should the
drum rust through.
Third through Tenth Year
Haier will provide the cabinet assembly
should the cabinet rust through.
NOTE:This warranty commences on the
date the item was purchased and the original
purchase receipt must be presented to the
authorized service representative before
warranty repairs are rendered.
Exceptions: Commercial or Rental
Use Warranty
90 days labor from date of original 
purchase. Excludes in-home trip charge.
90 days parts from date of original
purchaseNo other warranty applies
For Warranty Service
Contact your nearest authorized service 
center. All service must be performed by a
Haier authorized service center. For the name
and telephone number of the nearest 
authorized service center please 
call 1-877-337-3639.
Before calling please have available
the following information:
Model number and serial number of your
appliance (found on the rear of the unit on
the upper left hand side).
The name and address of the dealer 
you purchased the unit from and the 
date of purchase.
A clear description of the problem.
A proof of purchase (sales receipt).This warranty covers appliances
within the continental United States,
Puerto Rico and Canada.
What is not covered by 
this warranty:
Replacement or repair of household fuses, 
circuit breakers, wiring or plumbing. 
A product whose original serial number has
been removed or altered.
Premium service charges not specifically 
identified as normal, such as outside normal
service area or hours.
Damage to clothing
Damage incurred in shipping
Damage caused by improper installation or
maintenance
Damage from misuse, abuse accident, fire,
flood, or acts of nature
Damage from service other than an 
authorized Haier dealer or service center
Damage from incorrect electrical current, 
voltage or supply
Damage resulting from any product 
modification, alteration or adjustment not
authorized by Haier.
Adjustment of consumer operated controls as
identified in the owners manual
Hoses, knobs, lint trays and all attachments,
accessories and disposable parts
Labor, service transportation, and shipping
charges for the removal and replacement of
defective parts beyond the initial 
12-month period.
Damage from other than normal 
household use.
Any transportation and shipping charges.
THIS LIMITED WARRANTY IS GIVEN IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED
OR, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE
The remedy provided in this warranty is
exclusive and is granted in lieu of all 
other remedies.
This warranty does not cover incidental or
consequential damages, so the above 
limitations may not apply to you. Some states
do not allow limitations on how long an
implied warranty lasts, so the above 
limitations may not apply to you.
This warranty gives you specific legal rights,
and you may have other rights, which vary,
from state to state.
Haier America Trading L.L.C.
New York, NY 10018.GDZ5-1 manual  10/22/01  11:44 AM  Page 26 
						

							gdz5-1-02
Issued: July-01IMPORTANT
Do Not Return This Product To The Store
If you have a problem with this product, please contact the Haier Customer
Satisfaction Center at 1-877-337-3639.
DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE
IMPORTANT
Ne pas Réexpédier ce Produit au Magasin
Pour tout problème concernant ce produit, veuillez contacter le service des 
consommateurs ‘Haier Customer Satisfaction Center’ au 1-877-337-3639.
UNE PREUVE D’ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE.
IMPORTANTE
No regrese este producto a la tienda
Si tiene algún problema con este producto, por favor contacte el Centro de Servicio al
Consumidor de Haier al 1-877-337-3639 (Válido solo en E.U.A).
NECESITA UNA PRUEBA DE COMPRA FECHADA PARA EL SERVICIO DE LA GARANTIA
240 V, 60 Hz
Made in China
Fabriqué en Chine
Hecho en China
Haier America Trading, L.L.C. 
New York, NY 10018
Printed in ChinaPart # WD-9999-07GDZ5-1 manual  10/22/01  11:44 AM  Page 80