Haier Dw12 Pfe2 Instructions For Use

20
Inspect the nozzles in the spray arms for blocked holes
due to remnants of food.
If necessary, pull the lower arm “ 11 ” upwards and lift it off.
Unscrew the upper spray arm “ 10 ”.
Clean both spray arms under running water.
Refit the spray arms. Ensure that the lower arm has locked
into place and the upper one is screwed tight.
Spray arms
Lime and remnants of food in the washing water can block the
nozzles in the spray arms “ 10 ” and “ 11 ”  and the arm
mountings.
10
11
 

21
Resolving minor problems yourself
Experience has shown that you can resolve most problems that  rise during normal daily usage yourself,
without having to call out a service engineer.Not only does this save costs,but it also means that the
appliance is available for use again that much sooner. The following list of common occurrences and
their remedies should help you identify the causes of most problems.
Problems...
...when the appliance is switched on
Appliance does not start up
Caution
Do not...

22
When the programme indicators  “ J1,J3,J4” blink.
Have you checked whether:
the drain hose is crimped or bent.
the drain hose is too high.
When the programme indicators “ J1,J2,J6” blink.
Have you checked whether:
the drain hose is too low.
If you take all these checks and the dishwasher still does not function or your dish-
washer have any other error display, you can power the dishwasher OFF, and wait a few
minutes. You can power the dishwasher on, try it again , if the dishwasher still does not...

23
Water remains inside appliance after programme has ended
Blockage or kind in drainage hose.
Pump is jammed.
Filters are blocked.
The programme is still running. Wait for the programme to end .
...during washing
Unusual amount of foam is creased
Normal washing up liquid has been poured into the rinse-aid container.
Appliance stops suddenly while washing is taking place
Cut off electricity supply to appliance.
Water supply has been interrupted.
Knocking sound can be heared while washing is taking place...

24
Not enough detergent was added to dispenser.
Detergent has insuffcient bleaching properties. Use a detergent containing a chemical bleaching agent.
Plastic items are discoloured
Not enough detergent was added to dispenser compartment.
Amount of rinse-aid was set too low.
Although water is quite hard, no salt has been put in appliance.
Water softener was set too low.
Lid on salt container is not screwed tight.
If you used a phosphate-free detergent , try a detergent containing phosphates and compare...

25
Technical data
12 standard place settings Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorbed power
   60 cm
60 cm
85 cm
0.03-0.6MPa
220-240V~   50Hz
1950W
Maximum current intensity10A
Important information
Notes on waste disposal
Old appliances still have some residual value. An environment-friendly method of disposal will ensure
that valuable raw materials can be recovered and used again.
When an appliance has reached the end of its working life,unplug it from the mains.Cut...

26
General information
Measures must be taken to ensure that built-under and built-in units that are subsequently re-sited
as free-standing appliances cannot topple over. This can be achieved by bolting the dishwasher to
the wall or fitting it under a continuous work surface which is screwed to the adjacent cupboards.
Information on comparability tests implemented in compliance with
EN 50242
Appliance loaded in accordance with standard specifications.
Example of loaded dishwasher: See Fig 1 and 2...

A: Wiring box
B: Door switch
C: Water level switch
D: Drain pump motor
E: Dispenser
F: Softener valveG: Overflow switch
H1: Inlet valve
H2: Inlet valve (Aquastop)
 I: Washing pump motor
J: Temperature limiter
K: HeaterL: Relay
M: Low salt switch
N: Low rinse aid switch
O: Temperature sensor
P: Flowmeter
Disposal
The symbol           on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for...