GoPro Hero3 Plus Black User Manual

							59
B AT T E R Y
CHARGING THE BATTERY
The battery icon displayed in the camera’s LCD will blink when the battery drops 
below 10%. If recording is occurring when battery reaches 0%, the camera will 
save the file and power OFF.
To charge the battery: 
1.  Connect the camera to a 
computer or USB power supply 
(such as the Wall Charger or Auto 
Charger).
2.   The  red  Status Indicator Light 
remains  ON while the battery 
is charging.
3.   The red  Status Indicator Light   
will turn OFF when the battery is 
fully charged. 
You can also charge the battery outside the camera using the Dual Battery Charger 
(optional accessory, sold separately).
No damage will occur to the camera or the battery if used prior to full charge. 
Spare batteries and additional charging accessories are available at: gopro.com.  
						

							60
B AT T E R Y
USING THE CAMERA WHILE CHARGING
You can capture Video and Photos while charging the camera’s battery.  
Simply plug the camera into a computer or any USB charging device using the 
included USB Cable. 
REMOVING THE BATTERY FROM THE CAMERA
The HERO3+ battery is designed to have a tight fit to maximize reliability  
in high-vibration activities.
To remove the battery:
1.   Remove the battery door by placing your thumb in the indentation in the 
battery door (on the back of the camera) and sliding it to the left.
2.   Allow the door to pop out. Grasp the battery pull-tab and remove from the camera.  
						

							61
IMPORTANT WARNING ME SSAGE S
MICROSD CARD MESSAGES
NO SD  No card present. The camera requires a microSD, 
microSDHC 
or  microSDXC card to record Video or take Photos.
SD FULL Card is full. Delete files or swap card.
SD ERROR Camera unable to access card.
FILE REPAIR ICON ON THE LCD 
If you see the File Repair icon on the LCD screen, your Video file 
was corrupted during recording. Press any button and the camera 
will repair the file.
TEMPERATURE WARNING ICON ON THE LCD 
The Temperature Warning icon will appear on the LCD when the 
camera has become too hot and needs to cool down. Simply let it sit 
and cool before attempting to use it again. Your camera will not allow 
itself to overheat   —do not worry, no damage has occurred.  
						

							62
CAMERA HOUSING
ASSEMBLING THE CAMERA HOUSING  
To remove camera from housing:
1. Lift front of latch up to disengage from camera housing.
2. Pivot latch backward and pull up to release backdoor.
3. Pull open housing backdoor and remove camera. 
Slim housing surfboard mount installation
Slim housing remove camera
Slim housing insert camera
Slim housing closed Swapping housing doors
Quick Release Buckle + Thumb Screw + Slim housing = Complete Unit
To secure camera in housing:
1. Open housing and drop camera into position. 
2. Close housing backdoor.
3.  Pivot hinged arm backwards and hook lip of latch into grooved top  
of housing backdoor. 
4. Push latch down to snap into place.
Slim housing surfboard mount installation
Slim housing remove camera
Slim housing insert camera
Slim housing closed Swapping housing doors
Quick Release Buckle + Thumb Screw + Slim housing = Complete Unit  
						

							63
CAMERA HOUSING
Your HERO3+ camera housing comes with two types of backdoors— Skeleton (non-waterproof) and Standard (waterproof).  
Skeleton BackdoorStandard Backdoor
The Skeleton Backdoor (non-waterproof) 
provides better sound quality by allowing 
more sound to reach the camera’s 
microphone. It also reduces wind noise 
at speeds up to 100mph when mounted 
on helmets, motorcycles, bikes and other 
fast-moving vehicles. Use this backdoor 
only when sand, excessive dirt/dust 
and water damage is not a risk. This 
backdoor is also recommended for use 
inside vehicles.The Standard Backdoor makes the 
housing waterproof to 131’/40m. 
Use this door when you need to 
protect the camera from water and 
other environmental hazards. 
PRO 
TIP: Apply Rain-X or a similar anti-beading solution to the camera 
housing lens to prevent water spots from forming when using your 
camera in rain or water. When Rain-X is not available, periodically 
licking your lens is a good backup solution. Trust us, it works.   
						

							64
CAMERA HOUSING
SWAPPING BACKDOORS
You can switch the Backdoor of your HERO3+ camera to suit your activity and 
shooting conditions.
To change backdoor: 
1. Open the Backdoor of the housing so that it is hanging downwards. 
2. Pull downwards on the Backdoor until it snaps free from the hinge.
3. Line up replacement Backdoor into the hinge opening.
4. Push upwards on the Backdoor until it clicks into place. 
Slim housing surfboard mount installation
Slim housing remove camera
Slim housing insert camera
Slim housing closed Swapping housing doors
Quick Release Buckle + Thumb Screw + Slim housing = Complete Unit  
						

							65
CAMERA HOUSING
PREVENTING WATER DAMAGE TO YOUR CAMERA
The rubber seal that lines the camera housing forms a waterproof barrier  
that protects your HERO3+ in wet and underwater conditions.
Keep the camera housing’s rubber seal clean. A single hair or grain of sand  
can cause a leak and damage your camera.
After every use in salt water, rinse the outside of the camera housing with  
non-salt water and dry. Not doing this can eventually cause corrosion of the 
hinge pin and salt buildup in the seal, which can cause failure. 
To clean the seal, rinse in fresh water and shake dry (drying with a cloth may 
cause lint to compromise the seal). Re-install the seal into the grooves in the 
backdoor of the camera housing. 
WARNING: Failure to follow these steps each time you use your 
HERO3+ can 
result in leaks that may damage or destroy your camera. Your warranty does not 
cover water damage resulting from user error.   
						

							66
USING THE MOUNTS
ATTACHING YOUR CAMERA TO MOUNTS
To attach your HERO3+ camera to a mount, you will need a Quick Release 
Buckle, thumb screw or hardware depending on the mount you are using.  
For more information on mounts, visit: gopro.com/support.
Slim housing surfboard mount installation
Slim housing remove camera
Slim housing insert camera
Slim housing closed Swapping housing doors
Quick Release Buckle + Thumb Screw + Slim housing = Complete Unit
Quick Release 
Buckle Thumb Screw
Housing Complete Unit
USING CURVED + FLAT ADHESIVE MOUNTS
The Curved + Flat Adhesive Mounts make it easy to attach the camera to curved   
and flat surfaces of helmets, vehicles and gear. Using the Quick Release Buckle,   
the assembled camera housing can be clicked on and off the secured Curved or   
Flat Curved Adhesive Mounts.
Flat Adhesive Mount Curved Adhesive Mount  
						

							67
USING THE MOUNTS
ATTACHING ADHESIVE MOUNTS 
PRO 
TIPS: Apply to clean surface only. Wax, oil, dirt or other debris  
will reduce adhesion, which can result in a weak bond  
and risk of losing camera should connection fail.
Attach mount in room temperature conditions.  
Mount’s adhesive will not bond properly if applied in  
cold or damp environments to cold or damp surfaces,  
or if the surface is not room temperature.
Adhesive mounts should only be mounted to smooth surfaces; 
porous or textured surfaces will not enable a proper bond. 
When applying mount, firmly press into place and ensure  
full contact over entire surface. 
For best results, attach the mount 24 hours prior to use.
▶See: gopro.com/support for more information on mounts.
Locking Plug 
Using the HERO3+ in high impact sports such as surfing or skiing 
where significant impact may occur? Use the special Locking Plug 
which securely locks the Quick Release Buckle fingers into place—
helping prevent accidental housing release from the mount.  
The circular ring fits over the thumbscrew and acts as a leash  
to prevent dropping or losing the locking plug  
						

							68
HANDLING THE WI-FI REMOTE
CAUTION
Failure to follow these safety instructions could result in damage to the Wi-Fi Remote  
or other property.
HANDLING
The Wi-Fi Remote contains sensitive components. Do not drop, disassemble, open, crush, 
bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign objects into either 
product. Do not use the Wi-Fi Remote if it has been damaged—for example, if the product is 
cracked, punctured or damaged by water.
KEEPING THE WI-FI REMOTE’S LCD CLEAN
Clean LCD screen immediately if it comes into contact with any contaminants that may \
cause 
stains, such as ink, dyes, makeup, dirt, food, oils and lotions. To clean the LCD, use a soft, 
slightly damp, lint-free cloth. Avoid getting moisture in openings. Don’t use window cleaners, 
household cleaners, aerosol sprays, solvents, alcohol, ammonia or abrasives to clean LCD.
WATER RESISTANCE
Do not submerge the Wi-Fi Remote in more than 10ft / 3m of water. Do not attempt to dry the 
Wi-Fi Remote with an external heat source, such as a microwave oven or hair dryer. Damage to 
the Wi-Fi Remote caused by excessive water pressure is not covered under warranty.
USING CONNECTORS AND PORTS
Never force a connector into a port. Check for obstructions on the port. If the c\
onnector and 
port don’t join with reasonable ease, they probably don’t match. Make sure that the connector 
matches the port and that you have positioned the connector correctly in relation to the port.
KEEPING THE WI-FI REMOTE WITHIN ACCEPTABLE TEMPERATURES
The Wi-Fi Remote is designed to be operated in temperatures between 0° C and 40° C and stored 
in temperatures between 0° C and 70° C. Extreme temperatures may temporarily affect battery 
life, or affect the functionality of the Wi-Fi Remote. Avoid dramatic changes in temperature or 
humidity when using the Wi-Fi Remote as condensation may form on or within the product. 
When you’re using the Wi-Fi Remote or charging the battery, it is normal for the product to get 
warm. The exterior of the product functions as a cooling surface that transfers heat from inside 
the unit to the cooler air outside.
USE WITH OTHER ELECTRONIC DEVICES
Users of digital transceivers (avalanche beacons) should consult with their user manuals 
regarding use of GoPro cameras and other GPS or electronic devices when engaged in the 
avalanche beacon search mode in order to limit potential interference.