GoPro Hero3 Black User Manual

							61
camera assemblY
The HERO3 housing comes with two types of backdoors—Skeleton and Standard. 
skeleton Backdoor standard Backdoor
The Skeleton Backdoor (non-waterproof) 
provides better sound quality by allowing 
more sound to reach the camera’s 
microphone. It also reduces wind noise 
at speeds up to 100mph when mounted 
on helmets, motorcycles, bikes and other 
fast-moving vehicles. Use this backdoor 
only when sand, excessive dirt/dust 
and water damage is not a risk. This 
backdoor is also recommended for use 
inside vehicles.The Standard Backdoor makes the 
housing waterproof to 197’/60m. 
Use this door when you need to 
protect the camera from water and 
other environmental hazards. 
Pro 
tiP: Apply RAIN-X or a similar anti-beading solution to the housing lens 
to prevent waterspots from forming when using your camera in rain 
or water. When RAIN-X is not available, periodically licking your 
lens is a good backup solution. Trust us, this works.    
						

							62
camera assemblY
sWAPPinG  housinG Doors
Your HERO3 camera housing comes with two types of backdoors—Standard and 
Skeleton (non-waterproof). 
t o change backdoor:  
1. Open the backdoor of the housing so that it is hanging downwards. 
2. Pull downwards on the backdoor until it snaps free from the hinge.
3. Line up replacement backdoor into the hinge opening.
4. Push upwards on the backdoor until it clicks into place.   
						

							63
camera assemblY
PreVentinG  WAter DAmAGe to Your CAmerA
The rubber seal that lines the camera housing forms a waterproof barrier that 
protects your HERO3 in wet and underwater conditions. Keep the camera housing’s 
rubber seal clean; a single hair or grain of sand can cause a leak.
After every use in salt water you will need to rinse the outside of the housing \
with non-salt water and dry. Not doing this can eventually cause corrosion of the 
hinge pin and salt buildup in the seal, which can cause failure. 
To clean the seal, rinse in fresh water and shake dry (drying with a cloth may 
cause lint to compromise the seal). Re-install the seal into the grooves in the 
backdoor of the housing. 
WArninG: Failure to follow these steps each time you use your 
HERO3 can 
result in leaks that may damage or destroy your camera. Your warranty does not 
cover water damage resulting from user error.   
						

							64
camera assemblY
Att AChinG  Your CAmerA  to mounts
To attach your HERO3 camera to a mount, you will need an attachment buckle, 
thumb screw or hardware depending on the mount you are using. For more 
information on mounts, visit gopro.com/support.
Attachment  Buckle thumb screw
WaterhousingComplete unit
usinG CurVeD  or FLAt ADhesiVe mounts
The curved and flat adhesive mounts make it easy to attach the camera to curved 
and flat surfaces of helmets, vehicles and gear. With the attachment buckle the 
assembled camera housing can be clicked on/ oFF the secured adhesive mounts.
Flat Adhesive mount Curved Adhesive mount  
						

							65
HandlinG tHe w i-fi r emote
CAution
Failure to follow these safety instructions could result in damage to the Wi-Fi Remote or other 
property.
hAnDLinG
The Wi-Fi Remote contains sensitive components. Do not drop, disassemble, open, crush, 
bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign objects into either 
product. Do not use the Wi-Fi Remote if it has been damaged—for example, if the product is 
cracked, punctured or damaged by water.
KeePinG the Wi-Fi remote’s LCD CLeAn
Clean LCD screen immediately if it comes into contact with any contaminants that may \
cause 
stains, such as ink, dyes, makeup, dirt, food, oils and lotions. To clean the LCD, use a soft, 
slightly damp, lint-free cloth. Avoid getting moisture in openings. Don’t use window cleaners, 
household cleaners, aerosol sprays, solvents, alcohol, ammonia or abrasives to clean LCD.
WA ter resist AnCe
Do not submerge the Wi-Fi Remote in more than 10ft / 3m of water. Do not attempt to dry the 
Wi-Fi Remote with an external heat source, such as a microwave oven or hair dryer. Damage to 
the Wi-Fi Remote caused by excessive water pressure is not covered under warranty.
usinG ConneCtors AnD Ports
Never force a connector into a port. Check for obstructions on the port. If the c\
onnector and 
port don’t join with reasonable ease, they probably don’t match. Make sure that the connector 
matches the port and that you have positioned the connector correctly in relation to the port.
KeePinG the Wi-Fi remote Within ACCePt ABLe temPerAtures
The Wi-Fi Remote is designed to be operated in temperatures between 0° C and 40° C and 
stored in temperatures between 0° C and 70° C. Extreme temperatures may temporarily 
affect battery life, or affect the functionality of the Wi-Fi Remote. Avoid dramatic changes in 
temperature or humidity when using the Wi-Fi Remote as condensation may form on or within 
the product. When you’re using the Wi-Fi Remote or charging the battery, it is normal for the 
product to get warm. The exterior of the product functions as a cooling surface that transfers 
heat from inside the unit to the cooler air outside.
use With other eLeCtroniC DeViCes
Users of digital transceivers (avalanche beacons) should consult with their user manuals 
regarding use of GoPro cameras and other GPS or electronic devices when engaged in the 
avalanche beacon search mode in order to limit potential interference.  
						

							66
camera assemblY
Att AChinG ADhesiVe mounts 
Pro  
tiPs: Apply to clean surface only. Wax, oil, dirt or other debris will 
reduce adhesion, which can result in a weak bond and risk of 
losing camera should connection fail.
Attach mount in room temperature conditions. Mount’s 
adhesive will not bond properly if applied in cold or damp 
environments to cold or damp surfaces, or if the surface is not 
room temperature.
Adhesive mounts should only be mounted to smooth surfaces; 
porous or textured surfaces will not enable a proper bond. 
When applying mount, firmly press into place and ensure full 
contact over entire surface. 
For best results, attach the mount 24 hours prior to use.
▶See gopro.com/support for more information on mounts.
Locking Plug 
Using the HERO3 in high impact sports such as surfing or skiing 
where significant impact may occur? Use the special locking 
plug which securely locks the attachment buckle fingers into 
place--helping prevent accidental housing release from the mount. 
The circular ring fits over the thumbscrew and acts as a leash to 
prevent dropping or losing the locking plug.  
						

							67
customer suPPort
GoPro is dedicated to providing the best possible 
service. To reach the GoPro Customer Support Team, 
visit gopro.com/support.