GLOCK 19 Manual

GLOCK INSTRUCTION FOR USE
for the Safe Action self-loading pistol
TAKE NOTE:Always assume that the GLOCK pistol or any other firearm is loaded is capable of being discharged
until you the user, have been personally convinced to the contrary. Until the magazine is removed
and you have inspected the chamber and complete the unloading procedures as presented on page
21, the firearm must be considered to be loaded and capable of being fired. Never aim at persons
when handling the weapon.
To reduce the...

CONTENTS· Take note
· General Description
· Main features
· Technical data
· Function of the weapon
· Components parts
· Exploded drawing
· Safety devices
· Sights
· Loading and Firing
· Unloading
· Dismantling
· Safety and guarantee instructions
GENERAL DESCRIPTIONThe GLOCK Safe-Action self-loading pistol, with no-compromise design, combines virtually all the
features demanded of the modern handgun of today - and tomorrow :
· Extreme low overall weight
· High Magazine capacity
· Maximum possible safety...

The weapon has passed the most stringent military and/or industry tests and is regarded as an
absolutely top-class product.
TECHNICAL DATAModel                     GLOCK    GLOCK    GLOCK
                           17       19       17L
--------------------------------------------------
Caliber                   9x19mm   9x19mm   9x19mm
Length (slide)            186mm    174mm    225mm
Height inc. mag.          138mm    127mm    138mm
Width                      30mm     30mm     30mm
Length between...

FUNCTION OF THE WAEPON1) State of the weapon: loaded, i.e., a round in the barrel, firing pin (5) partially tensioned and
secured, trigger (26), in the foremost position. the trigger safety integrated in the trigger is actuated
with the trigger finger in order to pull the trigger all the way.
2) When the trigger slack is taken up to the first pressure point (travel 5mm) the weapon is released
from safety, i.e. the trigger bar lies behind the safety ramp, the firing pin is under tension. As the
trigger is...

20Slide lock spring21Slide lock22Locking block23Trigger mechanism housing with ejector24Connector25Trigger spring25aNew York trigger spring25bNew York trigger spring plus26Trigger with trigger bar27Slide stop lever28Trigger bar29Trigger housing pin30Follower31Magazine spring32Magazine floor plate32aMagazine insert33Magazine tube34Locking pin for non 9mm GLOCK pistols(Table No. 1)
Above components part numbers are referring to the exploded drawing.
Note: A modified version of the Recoil spring/Recoil tube...

SAFETY DEVICESThe weapon has no externally located safety devices which need to be actuated separately. All the
safety or safety release devices function automatically.
1. TRIGGER SAFETYThis is incorporated into the trigger (26) in the form of a lever, and in the untouched state blocks the
trigger from being moved backwards. If the weapon is allowed to drop, or if the trigger is subject to
an off centre, lateral pressure, it is still impossible for a shot to be fired. This safety can only be
released by...

3. Pull back the slide with free hand, and allow it to spring forwards into the final position. The
trigger finger of the shooting hand remains outside the trigger guard. The weapon is now
secured and ready to fire.
4. After the last round has been fired, the slide remains open. Remove the empty magazine from
the weapon by pushing the magazine catch (19). Insert a new magazine and then either push
the slide stop lever (27) downwards (see photo), or pull the slide slightly backwards and allow it
to spring...

4. Removal of the slide (see photo) is carried out as follows:
– Grasp the pistol in the right or left hand in such a way that four fingers rest over the slide and
the thumb rests on the rear side of the receiver.
– Using the fingers draw back the slide (1) about 3mm
– Pull the slide lock (21)
– Push the slide forwards and separate it from the receiver.
If the slide is drawn back too far (more than 3mm), the trigger will move to the foremost forward
position. The slide will then not separate from the...

– With the slide removed, it is not permitted to tension and spring the firing pin (5) forward,
since this could damage the firing pin safety.
– The steel insert located in the cover platte (15) to the slide must not be removed.
4. No liability whatever can be accepted if inexpertly manufactured or inexpertly filled ammunition
is used.
All liability whatever is excluded in the event of these instructions not being observed.
CHECK OF SAFETY DEVICES
The following safety checks are to be carried out at...