Gigabyte Z97n Gaming 5 Manual

							- 61 -
Step 5:After setting the capacity, move to Create Volume	and	press		to	begin	(Figure	6).
After completing, you'll be brought back to the Intel(R) Rapid Storage Technology screen. Under RAID Volumes you can see the new RAID volume. To see more detailed information, press  on the volume to check fo\
r information	on	RAID	level,	stripe	block	size,	array	name,	and	array	capacity,	etc.	(Figure	7).
Figure 6
Figure 7
Configuring	SATA	Hard	Drive(s)  
						

							- 62 -
Delete RAID VolumeTo delete a RAID array, press  on the volume to be deleted on the Intel(R) Rapid Storage Technology screen. After entering the RAID VOLUME INFO screen, press  on Delete to enter the Delete screen. Press  on Yes	(Figure	8).
Figure 8
Configuring	SATA	Hard	Drive(s)  
						

							- 63 -
C-2.	Configuring	Legacy	RAID	ROMEnter the Intel®	legacy 	RAID	 BIOS	 setup	 utility	to	configure	 a	RAID	 array.	 Skip	this	step	 and	proceed	 with	the	installation	of	Windows	operating	system	for	a	non-RAID	configuration.
Step 1:After the POST memory test begins and before the operating system boot begins, look fo\
r a message which says "Press	 	 to	enter	 Configuration	 Utility"	(Figure	 9).	Press	 	 +		 to	enter	 the	RAID	 Configuration	 Utility.
Figure 9
Step 2:After you press  + , the MAIN MENU	screen	will	appear.	(Figure	10)
Create RAID VolumeIf you want to create a RAID array, select Create RAID Volume in MAIN MENU and press .
Figure 10
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C) Intel Corporation.   All Rights Reserved.
RAID Volumes :None defined.
Physical Devices :ID   Device Model  Serial #     Size Type/Status(Vol ID)1   Hitachi HDS72105  JP1532FR3BWV7K   465.7GB Non-RAID Disk2   Hitachi HDS72105  JP1532ER046M2K    465.7GB Non-RAID Disk
Press    to enter Configuration Utility...
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
4. Recovery Volume Options5. Acceleration Options6. Exit
RAID Volumes :None defined.
Physical Deivces :ID    Device Model    Serial #   Size Type/Status(Vol ID)1   Hitachi HDS72105  JP1532FR3BWV7K 465.7GB Non-RAID Disk2   Hitachi HDS72105  JP1532ER046M2K 465.7GB Non-RAID Disk
  [hi]-Select   [ESC]-Exit [ENTER]-Select  Menu
[ DISK/VOLUME INFORMATION ]
[ MAIN MENU ]1. Create RAID Volume2. Delete RAID Volume3. Reset Disks to Non-RAID
Con
						

							- 64 -
Step 3:After entering the CREATE VOLUME MENU	screen,	 enter	a	volume	 name	with	1~16	 letters	 (letters	 cannot	be	special	 characters)	 under	the	Name	item	 and	press	 .	 Then,	select	 a	RAID	 level	(Figure	 11).	RAID	levels	 supported	 include	RAID	0,	RAID	 1,	Recovery,	 RAID	10,	and	 RAID	 5	(the	 selections 	available	 depend	on	the	number	of	the	hard	drives	being	installed).	Press		to	proceed.
Step 4:Under Disks item, select the hard drives to be included in the RAID array. If only two hard drives are installed, they	will	be	automatically	 assigned	to	the	 array.	 Set	the	stripe	 block	size	(Figure	 12)	if	necessary.	 The	stripe	 block	size	can	be	set	from	4	KB	to	128	KB.	Once	you	have	selected	the	stripe	block	size,	press	.
Figure 11
Figure 12
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
RAID 0: Stripes data (performance).
   [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
  Name : Volume0  RAID Level : RAID0(Stripe)  Disks : Select Disks Strip Size :     16KB  Capacity : 931.5 GB  Sync : N/A   Create Volume
[ CREATE VOLUME MENU ]
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
                    The following are typical values:
          RAID0 - 128KB           RAID10 - 64KB           RAID5 - 64KB
  [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
[ CREATE VOLUME MENU ]  Name : Volume0  RAID Level : RAID0(Stripe)  Disks : Select Disks Strip Size :     16KB  Capacity : 931.5 GB  Sync : N/A   Create Volume
Configuring	SATA	Hard	Drive(s)  
						

							- 65 -
Step 5:Enter the array capacity and press . Finally press  on the Create Volume item to begin creating the	RAID	 array.	 When	 prompted	 to	confirm	 whether	 to	create	 this	volume,	 press		to	confirm	 or		 to	cancel	(Figure	13).
When completed, you can see detailed information about the RAID array in the DISK/VOLUME INFORMATION section,	including	the	RAID	level,	stripe	block	size,	array	name,	and	array	capacity,	etc.	(Figure	14).
To exit the RAID BIOS utility, press  or select 6. Exit in MAIN MENU.
Now, you can proceed to install the SATA RAID/AHCI driver and operating system.
Figure 13
Figure 14
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright(C) Intel Corporation.  All Rights Reserved.
Press ENTER to create the specified volume.
   [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
  Name : Volume0  RAID Level : RAID0(Stripe)  Disks : Select Disks Strip Size : 128 MB  Capacity : 931.5 GB  Sync : N/A   Create Volume
[ CREATE VOLUME MENU ]
WARNING : ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N) :
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
RAID Volumes :ID    Name     Level    Strip Size Status Bootable0  Volume0    RAID0(Stripe)  128KB 931.5GB Normal Ye s
Physical Devices :ID   Device Model    Serial #   Size Type/Status(Vol ID)1   Hitachi HDS72105  JP1532FR3BWV7K 465.7GB Member Disk(0)2   Hitachi HDS72105  JP1532ER046M2K 465.7GB Member Disk(0)
  [hi]-Select   [ESC]-Exit [ENTER]-Select  Menu
[ DISK/VOLUME INFORMATION ]
[ MAIN MENU ]4. Recovery Volume Options5. Acceleration Options6. Exit
1. Create RAID Volume2. Delete RAID Volume3. Reset Disks to Non-RAID
Configuring	SATA	Hard	Drive(s)  
						

							- 66 -
Recovery Volume OptionsIntel® Rapid Recover Technology provides data protection by allowing users to easily restore data and system operation using a designated recovery drive. With the Rapid Recovery Technology, which employs RAID 1 functionality,	users	can	copy	 the	data	 from	 the	master	 drive	to	the	 recovery	 drive;	if	needed,	 the	data	 on	the	recovery drive can be restored back to the master drive.
Before you begin: •The recovery drive must have equal or greater capacity than the master d\
rive. •A recovery volume can be created with two hard drives only. A recovery volume and a RAID array cannot co-exist in the system at the same time, that is, if you have already creat\
ed a recovery volume, you are unable to create a RAID array. •By	default,	only	the	master	drive	can	be	viewed	in	the	operating	system;	the	recovery	drive	is	hidden.
Figure 15
Step 1:Select Create RAID Volume	in	MAIN	MENU	and	press		(Figure	15).
Figure 16
Step 2:After entering the volume name, select Recovery under the RAID Level	item	and	press		(Figure	16).
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
RAID Volumes :None defined.
Physical Disks :ID    Drive Model    Serial #   Size Type/Status(Vol ID)1   Hitachi HDS72105  JP1532FR3BWV7K 465.7GB Non-RAID Disk2   Hitachi HDS72105  JP1532ER046M2K 465.7GB Non-RAID Disk
  [hi]-Select   [ESC]-Exit [ENTER]-Select  Menu
[ DISK/VOLUME INFORMATION ]
[ MAIN MENU ]4. Recovery Volume Options5. Acceleration Options6. Exit
1. Create RAID Volume2. Delete RAID Volume3. Reset Disks to Non-RAID
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
Recovery: Copies data between a master and a recovery disk.
   [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
  Name : Volume0  RAID Level : Recovery  Disks : Select Disks Strip Size : N/A  Capacity : 465.7 GB  Sync : Continuous   Create Volume
[ CREATE VOLUME MENU ]
Configuring	SATA	Hard	Drive(s)  
						

							- 67 -
Step 3:Press  under the Select Disks item. In the SELECT DISKS box, press  on the hard drive you want to	use	 for	the	 master	 drive	and	press	 	 on	the	 hard	 drive	 you	want	 to	use	 for	the	 recovery	 drive.(Make	 sure	the	recovery	 drive	has	equal	 or	larger	 capacity	 than	the	master	 drive.)	Then	press	 	 to	confirm	 (Figure	17).
Figure 17
Step 4:Under Sync, select Continuous or On Request	(Figure	 18).	When	 set	to	Continuous, changes made to the data on the master drive will be automatically and continuously copied to the recovery drive when both hard drives are installed in the system. On Request allows users to update data from the master drive to the recovery drive manually using the Intel® Rapid Storage Technology utility in the operating system. On Request also allows users to restore the master drive to a previous state.
Step 5:Finally press  on the Create Volume item to begin creating the Recovery Volume and follow the on-screen instructions to complete.
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
Choose the RAID level:RAID0: Stripes data (performance).RAID1: Mirrors data (redundancy).Recovery: Copies data between a master and a recovery disk.RAID10: Mirrors data and stripes the mirror.RAID5: Stripes data and parity.
   [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
[ CREATE VOLUME MENU ]  Name : Volume0  RAID Level : Recovery  Disks : Select Disks Strip Size :   128KB  Capacity : 223.6 GB   Create Volume
[ SELECT DISKS ]
  [hi]-Prev/Next   [TAB]-(M)aster  [SPACE]-(R)ecovery  [ENTER]-Done
ID    Drive Model  Serial #    Size StatusM1  Hitachi HDS72105  JP1532FR3BWV7K  465.7GB Non-RAID DiskR2  Hitachi HDS72105  JP1532ER046M2K  465.7GB Non-RAID Disk
                                Select 1 Master and 1 Recovery disk to c\
reate volume. 
Figure 18
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
Select a sync option:On Request: volume is updated manuallyContinuous: volume is updated automatically
  [hi]-Change  [TAB]-Next  [ESC]-Previous Menu  [ENTER]-Select
[ HELP ]
  Name : Volume0  RAID Level : Recovery   Disks : Select Disks Strip Size : N/A  Capacity : 0.0 GB  Sync : Continuous   Create Volume
[ CREATE VOLUME MENU ]
Configuring	SATA	Hard	Drive(s)  
						

							- 68 -
Acceleration OptionsThis	option	 allows	 you	to	view	 the	status	 of	your	 accelerated	 drive/volume	 (Figure	20)	created	 using	the	Intel® IRST utility. In case you are unable to run the Intel® IRST utility due to an application error or operating system issue,	 you	will	need	 to	remove	 acceleration	 or	manually	 enable	synchronization	 (Maximized	mode	only)	using	this option in the RAID ROM utility.Steps:Select Acceleration Options in MAIN MENU and press .To	remove	the	acceleration,	select	the	accelerated	drive/volume,	press	,	and	press		to	confirm.To	synchronize	 data	from	 the	cache	 device	 to	the	 accelerated	 drive/volume,	 press		and	press	 	to	confirm.
Figure 20
Delete RAID VolumeTo delete a RAID array, select Delete RAID Volume in MAIN MENU and press . In the DELETE VOLUME MENU section, use the up or down arrow key to select the array to be deleted and press . When	prompted	to	confirm	your	selection	(Figure	19),	press		to	confirm	or		to	abort.
Figure 19
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
Deleting a volume will reset the disks to non-RAID.WARNING:  ALL DISK DATA WILL BE DELETED.(This does not apply to Recovery volumes)
   [hi]-Select   [ESC]-Exit [DEL]-Delete  Volume
[ HELP ]
[ DELETE VOLUME MENU ]Name Level  Drives Capacity Status BootableVolume0 RAID0(Stripe)      2 931.5GB Normal Ye s
ALL DATA IN THE VOLUME WILL BE LOST!(This does not apply to Recovery volumes)Are you sure you want to delete "Volume0"? (Y/N) :
[ DELETE VOLUME VERIFICATION ]
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
Press 's'  to synchronize data from the cache device tothe Accelerated  Disk/Volume
Press 'r' to remove the Disk/Volume AccelerationWARNING:  IT IS RECOMMENDED THAT YOU PERFORM A SYNCHRONIZATIONBEFORE  REMOVING ACCELERATION
    [hi]-Select    [ESC]- Previous Menu 
[ HELP ]
[ ACCELERATION OPTIONS ]Name Type  Capacity Mode Status DISK PORT 3 Non-RAID Disk  465.7GB Enhanced In Sync 
Configuring	SATA	Hard	Drive(s)  
						

							- 69 -
3-2 Installing the SATA RAID/AHCI Driver and Operating System
With the correct BIOS settings, you are ready to install the operating s\
ystem.
A. Installing the Operating System
As Windows 7 already include Intel SATA RAID/AHCI driver, you do not need to install separate RAID/AHCI driver during the Windows installation process. After the operating system is installed, we recommend that you install	all	required	 drivers	from	the	motherboard	 driver	disk	using	 "Xpress	 Install"	to	ensure	 system	 performance	and compatibility. To install Windows 8.1/8, refer to the steps below:
Step 1:Copy the IRST folder under BootDrv in the driver disk to your USB thumb drive.
Step 2:Boot from the Windows 8.1/8 setup disk and perform standard OS installat\
ion steps. When the screen requesting you to load the driver appears, select Browse.
Step 3:Then	browse	 to	the	 USB	 flash	 drive	 and	select	 the	location	 of	the	 driver.	 The	locations	 of	the	 drivers	 are	as	follows:Windows 32-bit: \iRST\32BitWindows 64-bit: \iRST\64Bit
Step 4:When a screen as shown in Figure 1 appears, select Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller and click Next to load the driver and continue the OS installation. 
Figure 1
Configuring	SATA	Hard	Drive(s)  
						

							- 70 -
Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
3. Reset Disks to Non-RAID4. Exit
RAID Volumes :None defined.
Physical Disks :ID    Drive Model    Serial #   Size Type/Status(Vol ID)0   Hitachi HDS72105  JP1532FR3BWV7K 465.7GB Member Disk (0)1   Hitachi HDS72105  JP1532FR3ABMPK 465.7GB Non-RAID Disk
  [hi]-Select   [ESC]-Exit [ENTER]-Select  Menu
[ DISK/VOLUME INFORMATION ]
[ MAIN MENU ]
1. Create RAID Volume2. Delete RAID Volume[ DEGRADED VOLUME DETECTED ]
 [hi]-Previous/Next  [ENTER]-Select  [ESC]-Exit
"Degraded volume and disk available for rebuilding detected. Selecting a disk initiates a rebuild. Rebuild completes in the operating system.
Select the port of the destination disk for rebuilding (ESC to exit):
 ID  Drive Model    Serial #         Size 1  Hitachi HDS721050CLA    JP1532FR3ABMPK    465.7GB
B. Rebuilding an ArrayRebuilding is the process of restoring data to a hard drive from other drives in the array. Rebuilding applies only to fault-tolerant arrays such as RAID 1, RAID 5 or RAID 10 arrays. The procedures below assume a new drive is	added	 to	replace	 a	failed	 drive	to	rebuild	 a	RAID	 1	array.	 (Note:	 The	new	 drive	 must	have	 equal	 or	greater	capacity	than	the	old	one.)
Turn off your computer and replace the failed hard drive with a new one. Restar\
t your computer.
 •Enabling Automatic RebuildStep 1:When	 the	message	 "Press		 to	enter	 Configuration	 Utility"	appears,	 press		 +		 to	enter	 the	RAID	Configuration	Utility.	 The	following	screen	appears	after	you	enter	the	RAID	Configuration	Utility.
Step 2:Select the new hard drive to add into the array to be rebuilt and press \
. The following screen appears, indicating that an automatic rebuild will be performed after you enter the operating system. If you do not enable automatic	rebuild	on	this	 stage,	 you	have	 to	manually	 rebuild	the	array	 in	the	 operating	 system	(see	the	next	page	for	more	details).Intel(R) Rapid Storage Technology - Option ROM - 13.0.0.2075Copyright (C)  Intel Corporation.   All Rights Reserved.
RAID Volumes :ID    Name     Level    Strip Size Status Bootable0  Volume0    RAID1(Mirror)  N/A  465.7GB Rebuild Ye s
Physical Devices :ID    Devices Model    Serial #   Size Type/Status(Vol ID)0   Hitachi HDS72105  JP1532FR3BWV7K 465.7GB Member Disk (0)1   Hitachi HDS72105  JP1532FR3ABMPK 465.7GB Member Disk (0)
  [hi]-Select   [ESC]-Exit [ENTER]-Select  Menu
[ DISK/VOLUME INFORMATION ]
Volumes with "Rebuild" status will be rebuilt within the operating system\
.
[ MAIN MENU ]4. Recovery Volume Options5. Acceleration Options6. Exit
1. Create RAID Volume2. Delete RAID Volume3. Reset Disks to Non-RAID
Configuring SATA Hard Drives