Gigabyte Z170n-gaming 5 Manual

2-5 Peripherals
 &Intel Platform Trust Technology (PTT)
 Enables or disables Intel® PTT Technology. (Default: Disabled)
 &Initial Display Output
 Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard 
graphics.
 IGFX      Sets the onboard graphics as the first display.
 PCIe 1 Slot  Sets the graphics card on the PCIEX16 slot as the first display. (Default)
 &OnBoard LAN Controller
 Enables or disables the onboard LAN function....

 `Intel(R) Bios Guard Technology 
 Enables or disables the Intel® BIOS Guard feature, which protects the BIOS from malicious attacks.
 `SATA 	Configuration	
 &SATA Controller(s) 
 Enables or disables the integrated SATA controllers. (Default: Enabled)
 &SATA Mode Selection 
 Enables or disables RAID for the SATA controllers integrated in the Chipset or configures the SATA controllers 
to AHCI mode.
 RAID      Enables RAID for the SATA controller.
 AHCI       Configures  the  SATA  controllers...

 &VT-d (Note)
 Enables or disables Intel® Virtualization Technology for Directed I/O. (Default: Disabled)
 &Internal Graphics
 Enables or disables the onboard graphics function. (Default: Auto)
 &DVMT Pre-Allocated
 Allows you to set the onboard graphics memory size. Options are: 32M~512M (Default: 64M)
 &DVMT Total Gfx Mem
 Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX. 
(Default: 256m)
 &Audio Controller
 Enables or disables the onboard audio...

 &AC BACK
 Determines the state of the system after the return of power from an AC power loss.
 Always Off      The system stays off upon the return of the AC power.  (Default)
 Always On   The system is turned on upon the return of the AC power.
 Memory   The system returns to its last known awake state upon the return of the \
AC power.
 &Power On By Keyboard
 Allows the system to be turned on by a PS/2 keyboard wake-up event.
 Note: To use this function, you need an ATX power supply...

 &Soft-Off by PWR-BTTN
 Configures the way to turn off the computer in MS-DOS mode using the power button.
 Instant-Off    Press the power button and then the system will be turned off instantly. (Default)
 Delay 4 Sec.   Press and hold the power button for 4 seconds to turn off the system. If the power 
button is pressed for less than 4 seconds, the system will enter suspend\
 mode.
 &Power Loading 
 Enables or disables dummy load. When the power supply is at low load, a \
self-protection will...

2-9 Save & Exit
 &Save & Exit Setup
 Press  on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup 
program. Select No or press  to return to the BIOS Setup Main Menu.
 &Exit Without Saving
 Press  on this item and select Yes. This exits the BIOS Setup without saving the changes made 
in BIOS Setup to the CMOS. Select No or press  to return to the BIOS Setup Main Menu.
 &Load Optimized Defaults
 Press  on this item and select Yes to load the optimal BIOS default...

Chapter 3 Appendix
C-1.	UEFI	RAID	ConfigurationOnly Windows 10/8.1 64-bit supports UEFI RAID configuration.Steps:1. In BIOS Setup, go to BIOS Features and set Windows 8/10 Features to Windows 8/10 and CSM Support to Disabled. Save the changes and exit BIOS Setup.2. After the system reboot, enter BIOS Setup again. Then enter the Peripherals\Intel(R) Rapid Storage Technology sub-menu.
3. On the Intel(R) Rapid Storage Technology menu, press  on Create RAID Volume to enter the Create RAID Volume screen....

RAID 1, Recovery, RAID 10, and RAID 5 (the selections available depend on the number of the hard drives being installed). Next, use the down arrow key to move to Select Disks.4. Under Select Disks item, select the hard drives to be included in the RAID array. Press the  key on the hard drives to be selected (selected hard drives are marked with\
 "X"). Then set the stripe block size. The stripe block size can be set from 4 KB to 128 KB. Once you have selected the stripe block size, set the volume...

 •Before  installing  the  drivers,  first  install  the  operating  system.  (The  following  instructions  use 
Windows 8.1 as the example operating system.)
 •After installing the operating system, insert the motherboard driver disk into your optical drive. Click 
on the message "Tap to choose what happens with this disc" on the top-right corner of the screen 
and select "Run Run.exe." (Or go to My Computer, double-click the optical drive and execute the 
Run.exe program.)
3-2 Drivers...

Regulatory Statements
Regulatory NoticesThis document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose.Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change...