Gigabyte Gak8vm800m Manual

							BIOS Setup - 31 -
EnglishCapacity Capacity of currently installed hard disk.
Hard drive information should be labeled on the outside drive casing.  Enter the appropriate option
based on this information.
Cylinder Number of cylinders
Head Number of heads
Precomp Write precomp
Landing Zone Landing zone
Sector Number of sectors
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
None No floppy drive installed
360K, 5.25 5.25 inch PC-type standard drive; 360K byte capacity.
1.2M, 5.25 5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5 3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5 3.5 inch double-sided drive; 1.44M byte capacity. (Default value)
2.88M, 3.5 3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled Normal Floppy Drive. (Default value)
Drive A Drive A is 3 mode Floppy Drive.
Drive B Drive B is 3 mode Floppy Drive.
Both Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors The system boot will not stop for any error that may be detected and  you
will be prompted.
All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.
All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed
in the system.
The value of the base memory is typically 512K for systems with 512K memory installed on
the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPUs memory address map.
Total Memory
This item displays the memory size that used. 
						

							GA-K8VM800M(-RH) Motherboard - 32 -
English
2-2 Advanced BIOS Features
Hard Disk Boot Priority
Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use <
> or  to select a device, then press to move it up, or  to move it down the list. Press
 to exit this menu.
First / Second / Third Boot Device
Floppy Select your boot device priority by Floppy.
LS120 Select your boot device priority by LS120.
Hard Disk Select your boot device priority by Hard Disk.
CDROM Select your boot device priority by CDROM.
ZIP Select your boot device priority by ZIP.
USB-FDD Select your boot device priority by USB-FDD.
USB-ZIP Select your boot device priority by USB-ZIP.
USB-CDROM Select your boot device priority by USB-CDROM.
USB-HDD Select your boot device priority by USB-HDD.
Legacy LAN Select your boot device priority by Legacy LAN.
Disabled Disable this function.
Password Check
System The system can not boot and can not access to Setup page will be denied if the
correct password is not entered at the prompt.
Setup The system will boot, but access to Setup will be denied if the correct password is
not entered at the prompt. (Default value)
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Advanced BIOS Features
 `Hard Disk Boot Priority [Press Enter]
First Boot Device[Floppy]
Second Boot Device [Hard Disk]
Third Boot Device [CDROM]
 Password Check [Setup]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level`
Select Hard Disk Boot
Device Priority 
						

							BIOS Setup - 33 -
English2-3 Integrated Peripherals
IDE DMA transfer access
EnabledEnable IDE DMA transfer access. (Default value)
Disabled Disable this function.
On-Chip IDE Channel0
Enabled Enable onboard 1st channel IDE port. (Default value)
Disabled Disable onboard 1st channel IDE port.
On-Chip IDE Channel1
Enabled Enable onboard 2nd channel IDE port. (Default value)
Disabled Disable onboard 2nd channel IDE port.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Integrated Peripherals
IDE DMA transfer  access [Enabled]
On-Chip IDE Channel 0 [Enabled]
On-Chip IDE Channel 1 [Enabled]
OnChip Serial ATA [Enabled]
SATA Mode [RAID]
AC97 Audio[Auto]
VIA Onboard LAN [Enabled]
USB 1.1 Controller[Enabled]
USB 2.0 Controller[Enabled]
USB Keyboard Support[Disabled]
USB Mouse Support[Disabled]
On-Chip LAN Boot ROM[Disabled]
Onboard FDC Controller[Enabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Serial Port 2 [2F8/IRQ3]
UART Mode Select [Normal]
x UR2 Duplex  ModeHalf
Onboard Parallel Port [378/IRQ7]
Parallel Port Mode [SPP]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level`
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Integrated Peripherals
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level` Midi Port Address [Disabled]
x Midi Port IRQ 10 
						

							GA-K8VM800M(-RH) Motherboard - 34 -
English
OnChip Serial ATA
EnabledEnable VT8237R / VT8237R+ Serial ATA supported. (Default value)
DisabledDisable VT8237R / VT8237R+ Serial ATA supported.
SATA Mode
RAID Set onboard SATA mode to RAID. (Default value)
IDE Set onboard SATA mode to IDE.
AC97 Audio
Auto Enable onboard AC97 audio function. (Default value)
Disabled Disable this function.
VIA Onboard LAN
Enabled Enable VIA onboard LAN function. (Default value)
Disabled Disable this function.
USB 1.1 Controller
Disabled Disable USB 1.1 controller.
Enabled Enable USB 1.1 controller. (Default value)
USB 2.0 Controller
Disabled Disable USB 2.0 controller.
Enabled Enable USB 2.0 controller. (Default value)
USB Keyboard Support
Enabled Enable USB keyboard support.
Disabled Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled Enable USB mouse support.
Disabled Disable USB mouse support. (Default value)
On-Chip LAN Boot ROM
This function decide whether to invoke the boot ROM of the onboard LAN chip.
PXE Set On-Chip LAN Boot ROM to PXE.
RPL Set On-Chip LAN Boot ROM to RPL.
Disabled Disable this function. (Default value)
Onboard FDC Controller
Enabled Enable onboard FDC Controller. (Default value)Disabled Disable onboard FDC Controller.
Onboard Serial Port 1
Auto BIOS will automatically setup the Serial port 1 address.
3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled Disable onboard Serial port 1. 
						

							BIOS Setup - 35 -
EnglishOnboard Serial Port 2
Auto BIOS will automatically set up the  Serial port 2 address.
3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8/IRQ4.
2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8/IRQ4.
2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disabled Disable onboard Serial port 2.
UART Mode Select
This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.
Normal Set onboard I/O chip UART to Normal mode.(Default value)
IrDA Set onboard I/O chip UART to IrDA mode.
ASKIR Set onboard I/O chip UART to ASKIR mode.
UR2 Duplex Mode
This feature allows you to select IR mode.
This function is available only when UART Mode Select is not set to Normal.
Half IR Function Duplex Half. (Default value)
Full IR Function Duplex Full.
Onboard Parallel Port
Disabled Disable onboard LPT port.
378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)
278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.
3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP Using Parallel port as Standard Parallel Port. (Default value)
EPP Using Parallel port as Enhanced Parallel Port.
ECP Using Parallel port as Extended Capabilities Port.
ECP+EPP Using Parallel port as ECP and EPP mode.
Midi Port Address
300 Set Midi Port Address to 300.
330 Set Midi Port Address to 330
Disabled Disable this function. (Default value)
Midi Port IRQ
5 Set Midi Port IRQ to 5.
10 Set Midi Port IRQ to 10. (Default value) 
						

							GA-K8VM800M(-RH) Motherboard - 36 -
English
2-4 Power Management Setup
ACPI Suspend Type
S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)
S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).
USB Device Wake-Up From S3
Disabled Disable USB Device Wake-Up from S3. (Default value)
Enabled Enable USB Device Wake-Up from S3.
Soft-Off by PWRBTN
Instant-Off Press power button then Power off instantly. (Default value)
Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed
less than 4 sec.
AC BACK Function
Memory When AC-power back to the system, the system will be back to the last state
before AC-power is lost.
Soft-Off When AC-power back to the system, the system will be in Off state.
(Default value)
Full-OnWhen AC-power back to the system, the system always in On state.
Keyboard Power On
Password Enter from 1 to 8 characters to set the Keyboard Power On Password.
Disabled Disabled this function. (Default value)
Keyboard 98 If your keyboard have POWER Key button, you can press the key to power
on the system.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Power Management Setup
ACPI Suspend Type [S1(POS)]
x USB Device Wake-Up From S3Disabled
Soft-Off by PWRBTN [Instant-Off]
AC Back Function [Soft-Off]
Keyboard Power On [Disabled]
Mouse Power On[Disabled]
PME Event Wake Up [Enabled]
Modem Ring Resume [Enabled]
Resume by Alarm [Disabled]
x Date (of Month) AlarmEveryday
x Time (hh:mm:ss) Alarm 0 : 0 : 0
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level`
[S1]
Set suspend type to
Power On Suspend under
ACPI OS
[S3]
Set suspend type to
Suspend to RAM under
ACPI OS 
						

							BIOS Setup - 37 -
EnglishMouse Power On
Disabled Disabled this function. (Default value)
Enabled Double click on PS/2 mouse left button to power on the system.
PME Event Wake Up
This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.
Disabled Disable this function.
Enabled Enable PME as wake up event. (Default value)
Modem Ring Resume
An incoming call via modem can awake the system from any suspend state.
Disabled Disable Modem Ring Resume function.
Enabled Enable Modem Ring Resume function. (Default value)
Resume by Alarm
You can set Resume by Alarm item to enabled and key in Date/Time to power on system.
Disabled Disable this function. (Default value)
Enabled Enable alarm function to POWER ON system.
If Resume by Alarm is Enabled.
Date (of Month) Alarm : Everyday, 1~31
Time (hh: mm: ss) Alarm: (0~23) : (0~59) : (0~59) 
						

							GA-K8VM800M(-RH) Motherboard - 38 -
English
2-5 PnP/PCI Configurations
PCI 1 IRQ Assignment
Auto Auto assign IRQ to PCI 1. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
PCI 2 IRQ Assignment
Auto Auto assign IRQ to PCI 2. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto Auto assign IRQ to PCI 3. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PnP/PCI Configurations
PCI 1 IRQ Assignment[Auto]
PCI 2 IRQ Assignment[Auto]
PCI 3 IRQ Assignment[Auto]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level` 
						

							BIOS Setup - 39 -
English2-6 PC Health Status
Current Voltage(V) Vcore / DDR25V / +3.3V / +12V
Detect systems voltage status automatically.
Current CPU Temperature
Detect CPU temperature automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM fan speed status automatically.
CPU FAN Fail Warning
Disabled Disable CPU fan fail warning function. (Default value)
Enabled Enable CPU fan fail warning function.
SYSTEM FAN Fail Warning
Disabled Disable SYSTEM fan fail warning function. (Default value)
Enabled Enable SYSTEM fan fail warning function.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PC Health Status
Vcore OK
DDR25V OK
+3.3V OK
+12V OK
Current CPU Temperature35°C
Current CPU FAN Speed 3125 RPM
Current SYSTEM FAN Speed    0 RPM
CPU FAN Fail Warning [Disabled]
SYSTEM FAN Fail Warning[Disabled]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level` 
						

							GA-K8VM800M(-RH) Motherboard - 40 -
English
2-7 Frequency / Voltage Control
K8 CPU Clock Ratio
Default Set K8 CPU Clock Ratio to CPU factory default. (Default value)
x4 800Mhz ~ x10 2000Mhz Set K8 CPU Clock Ratio from x4 800Mhz to x10 2000Mhz.
CPU Host Clock Control
Note: Please note that if your system is overclocked and cannot restart, please wait 20secs.
for automatic system restart or clear the CMOS setup data and perform a safe restart.
Disabled Disable CPU Host Clock Control.(Default value)
Enabled Enable CPU Host  Clock Control.
CPU Host Frequency (Mhz)
200MHz ~455MHz Set CPU Host Frequency from 200MHz to 455MHz.
PCI /AGP Frequency(Mhz)
The values depend on CPU Host Frequency(Mhz).
CPU OverVoltage Control
Auto BIOS will automatically detect CPU voltage. (Default value)
+5% Set CPU OverVoltage Control to +5%.
+7.5% Set CPU OverVoltage Control to +7.5%.
+10% Set CPU OverVoltage Control to +10%.
Incorrect using it may cause your system broken. For power End-User use only!
AGP OverVoltage Control
Auto BIOS will automatically detect AGP voltage. (Default value)
+0.1V Set AGP OverVoltage Control to +0.1V.
+0.2V Set AGP OverVoltage Control to +0.2V.
Increase AGP voltage may get stable for Over_Clock. But it may damage to AGP Card when
enable this feature.Incorrect using these features may cause your system broken. For power end-user use only.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Frequency/Voltage Control
K8 CPU Clock Ratio [Default]
CPU Host Clock Control[Disabled]
x CPU Host Frequency 200
PCI/AGP Frequency33/66
CPU OverVoltage Control[Auto]
AGP OverVoltage Control[Audo]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level`