Gigabyte Ga7n400 Manual

- 47 - BIOS Setup
English
System Performance
NormalSet system at the most stable settings. (Default Value)
Turbo Use over colocked settings for higher performance but with higher risk of
instability.
Manual Allows full customization of performance options.
Incorrect using it may cause your system to fail. For power End-User use only!
FSB Frequency
100 MHz Set FSB frequency at 100MHz.
133 MHz Set FSB frequency at 133MHz. (Default Value)
166 MHz Set FSB frequency at 166MHz.
200 MHz Set FSB frequency at...

- 48 - N400 Pro2 / N400 Series Motherboard
English
Memory Frequency
By SPD Set memory frequency by SPD. (Default Value)
50%~200%Set the memory frequency manually.
AutoSet the best memory frequency for system.
Incorrect using it may cause your system to fail. For power End-User use only!
Resulting Frequency
The value depends on FSB/Memory Frequency.
AGP Frequency
NormalSet the best AGP frequency for system. (Default Value)
50MHz ~ 100MHzSet the AGP frequency manually.
Incorrect using it may cause your...

- 49 - BIOS Setup
EnglishIntegrated  Peripherals
On-Chip Primary PCI IDE [Enabled]
On-Chip Secondary PCI IDE [Enabled]
USB Host Controller[V1.1+V2.0]
USB Keyboard Support [Disabled]
USB Mouse Support [Disabled]
AC97 Audio[Auto]
Onboard LAN Chip
(
)[Enabled]
Onboard 1394 
(
)[Enabled]
Onboard H/W Serial ATA
(
)[Enabled]
Serial ATA Function 
(
)[RAID]
Onboard H/W RAID 
(
)[Enabled]
Onboard LAN Boot ROM
(
)[Disabled]
Onboard Serial Port 1[3F8/IRQ4]
Onboard Serial Port 2[2F8/IRQ3]
UART Mode Select[Normal]...

- 50 - N400 Pro2 / N400 Series Motherboard
English
On-Chip Primary PCI IDE
Enabled Enable onboard 1st channel IDE port. (Default value)
Disabled Disable onboard 1st channel IDE port.
On-Chip Secondary PCI IDE
Enabled Enable onboard 2nd channel IDE port. (Default value)
Disabled Disable onboard 2nd channel IDE port.
USB Host Controller
DisabledDisable USB controller.
V1.1+V2.0 Set USB controller at USB1.1 and USB2.0. (Default Value)
V1.1 Set USB controller at USB1.1.
USB Keyboard Support
EnabledEnable USB...

- 51 - BIOS Setup
EnglishOnboard H/W 1394 (
)
Enabled Auto detect on-chip 1394 function. (Default Value)
Disabled Disable this function.
Onboard H/W Serial ATA (
)
Enabled Enable onboard H/W Serial ATA chip function. (Default Value)
Disabled Disable this function.
Serial ATA  Function(
)
RAIDSelect onboard serial ATA chip function as RAID. (Default value)
BASESelect onboard serial ATA chip function as base.
Onboard  H/W RAID (
)
Enabled Enable onboard GigaRAID chip function. (Default value)
Disabled...

- 52 - N400 Pro2 / N400 Series Motherboard
English
Onboard Serial Port 2
Disabled Disable onboard Serial port 2.
3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8, using IRQ4.
2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8, using IRQ3. (Default value)
3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8, using IRQ4.
2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8, using IRQ3.
AutoBIOS will automatically setup the port 2 address.
UART Mode Select
This item allows you to...

- 53 - BIOS Setup
EnglishParallel Port Mode
This feature allows you to connect with an advanced printer via the port mode it supports.
SPP Using Parallel port as Standard Parallel Port.
EPP Using Parallel port as Enhanced Parallel Port.
ECP Using Parallel port as Extended Capabilities Port. (Default Value)
ECP+EPP Using Parallel port as ECP & EPP mode.
ECP Mode Use DMA
This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected.
This function will available when Parallel...

- 54 - N400 Pro2 / N400 Series Motherboard
English
Power Management Setup
ACPI Suspend Type
S1(POS) Set ACPI suspend type to S1. (Default Value)
S3(STR)Set ACPI suspend type to S3.
Off by Power button
Instant-offPress power button then Power off instantly. (Default value)
Delay 4 Sec.Press power button 4 sec. to Power off. Enter suspend if button is pressed
less than 4 sec.Figure 6: Power Management Setup
ACPI Suspend Type [S1(POS)]
Soft-Off by PWR-BTTN[Instant-off]
PME Event Wake Up [Enabled]...

- 55 - BIOS Setup
EnglishPME Event Wake Up
Disabled Disable this function.
Enabled Enable PME Event Wake up. (Default Value)
  ModemRingOn
An incoming call via modem can awake the system from any suspend state .
DisabledDisable Modem Ring on function.
Enabled Enable Modem Ring on function. (Default Value)
  S3 Resume by USB
You can resume the system from USB device.
Disabled Disable this function. (Default Value)
Enabled Enable this function.
  Resume by Alarm
You can set Resume by Alarm item to enabled...

- 56 - N400 Pro2 / N400 Series Motherboard
English
This feature allows you to set the method for powering-on the system.
The option Password allows you to set up to 5 alphanumeric characters to power-on the system.
The option Keyboard 98 allows you to use the standard keyboard 98 to power on the system.
PasswordEnter from 1 to 5 characters to set the Keyboard Power On Password.
Disabled Disabled this function. (Default value)
Keyboard 98 If your keyboard have POWER Key button, you can press the key to...