GGP Italy SPA Brush Cutter 1715010690 Operators Manual Norwegian Version

Pareiza tehniskÇ apkope ir ∫oti svar¥ga maš¥nas
sÇkotnïjÇs darb¥bas efektivitÇtes un droš¥bas
saglabÇšanai.
Veicot tehnisko apkopi:
– Atvienojiet sveces uzvÇzni. – Uzgaidiet, kad dzinïjs pietiekoši atdzis¥s.– StrÇdÇjot ar asme¿iem izmantojiet aizsarg- cimdus.
–  Asmens aizsargam jÇbt uzstÇd¥tam,
iz¿emot gad¥jumus, kad darb¥bas tiek veik-tas ar asmeni.
– Neizlejiet apkÇrtïjÇ vidï e∫∫as, benz¥nu un citas piesÇr¿ojošas vielas.
CILINDRS UN TROKŠøA SLÅPîTÅJS
Lai samazinÇtu ugunsgrïka risku bieži t¥riet...

Nepietiekamas darbspïjas gad¥jumÇ griezieties
pie vietïja izplÇt¥tÇja, lai vi¿š pÇrbaud¥tu
karburÇciju un dzinïju.
•
MinimÇlo apgriezienu rež¥ma regulïšana
MinimÇlo apgriezienu
rež¥ms ir jÇregulï tikai tajÇ gad¥jumÇ, ja grie- zïjier¥ce kustas, kamïr dzinïjs darbojasminimÇlo apgriezienu rež¥mÇ.
Lai samazinÇtu Çtrumu, ar simbolu «MIN»
apz¥mïtÇ skrve ir jÇpagriež pretïji
pulkste¿rÇd¥tÇja virzienam, l¥dz griezïjier¥ce
apstÇjas un dzinïjs darbojas pietiekoši vien-
mïr¥gi.
Ja dzinïja darb¥ba minimÇlo...

ÅRKÅRTîJA TEHNISKÅ APKOPE
Visas tehniskÇs apkopes darb¥bas, kuras nav
iek∫autas šajÇ rokasgrÇmatÇ, dr¥kst veikt tikai vie-
tïjais izplÇt¥tÇjs.
Ja darb¥bas veic neatbilstošajÇs darbn¥cÇs vai to
veic nekvalificïts personÇls, tas noved pie visu
veidu garantiju spïka zaudïšanas.
UZGLABÅŠANA
Pïc darba pabeigšanas rp¥gi not¥riet maš¥nu no
putek∫iem un atgriezumiem, salabojiet vai nomai-
niet bojÇtas da∫as.
Maš¥na jÇuzglabÇ sausÇ, no nelabvïl¥giem laika
apstÇk∫iem aizsargÇtÇ vietÇ un ar pareizi
uzstÇd¥tu...

TEHNISKIE DATI17LV
Dzinïjs  ........................................ 4 taktu ar gaisdzesi
Cilindru apjoms / Jauda
Mod. 28H - 28HD .......................... 25 cm3/ 0,81 kW
Mod. 38H - 38HD ............................ 35 cm3/ 1,2 kWDzinïja griešanÇs Çtrums minimÇlajÇ rež¥mÇ Mod. 28H - 28HD ...... 2900-3300 apgriezieni/mintïMod. 38H - 38HD ...... 2900-3300 apgriezieni/mintï
MaksimÇlais dzinïja griešanÇs Çtrums 
Mod. 28H - 28HD .. 10500-11000 apgriezieni/mintïMod. 38H - 38HD .. 10500-11000...

18 

ENINTRODUCTION1
Dear Customer,
thank you for choosing one of our products. We hope that you will be completely satisfied with this
machine and that it fully meets your expectations. This manual has been \
compiled in order to provide
you with all the information you need to get acquainted with the machine\
 and use it safely and effi-
ciently. Don’t forget that it is an integral part of the machine, so keep it handy so that\
 it can be con-
sulted when necessary, and pass it on to a further user if you...

EN
MAIN COMPONENTS
1. Power unit
2. Drive tube
3. Cutting devicea. Blade with 3 or 4 points
b. Cutting line head
4. Cutting device guard
5. Front handgrip
6. Guard
7. Handlebar
8. Rear handgrip
9. Connection point (of the webbing)
10. Identification plate
11. Webbing a. single belt
b. double belt
12. Angle transmission
13. Blade protection (for transport)
14. Spark plug
CONTROLS AND REFUELLING 
21. Engine stop switch
22. Throttle trigger
23. Throttle trigger lockout
24. Starter
25. Choke (if present)
26....

EN
1)Warning! Danger. The failure to use this
machine correctly can be hazardous for oneself
and others.
2)Read the instruction manual before using the
machine.
3)If you are using the machine every day in nor-
mal conditions, you can be exposed to a noise
level of 85 dB (A) or higher. 
W ear earmuffs or earplugs and a protective hel-
met.
4)W ear gloves and protective footwear!
11)Fuel tank
12)Engine stop switch posi-
tions
a= stopb= run
13)Tuning minimum speed 
14)Choke
15)Primer
16)Correct position of...

EN
A) TRAINING
1)Read the instructions carefully.Become
acquainted with the controls and the proper use
of the machine. Learn how to stop the engine
quickly.
2)
Only use the machine for the purpose for
which it was designed,namely
–cutting grass and non-woody vegetation,using a nylon line (e.g. around the edges of
lawns, flowerbeds, walls, fences and small
grassy areas to tidy up the cutting done using a
mower);
–
cutting tall grass, dry branches, twigs and
woody shrubsof up to 2 cm diameter, with the...

ground that does not guarantee stability for the
operator;
– never run, but walk carefully paying attention to
the lay of the land and any eventual obstacles;
– assess the potential risks of the ground to be
mown and take all necessary precautions to
ensure your own safety, especially on slopes or
on bumpy, slippery or unstable ground;
– work along the contour on slopes, never when
walking up or down and always keep downhill
of the cutter.  
4) Make sure the machine is securely locked
when you start the...