Getnet Router GR-154 User Manual

July 2009 
FCC Warning   
This equipment has been tested and found to comply with the limits for a class B digital device, 
pursuant to Part 15 of the FC C Rules. These limitations are designed to provide reasonable 
protection against harmful interfer ence in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not  installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no...

Contents                                            _____        
1. Introduction........................................................................\
....................................................... .........…….4 
1.1 Features........................................................................\
....................................................... ............ 4 
1.2 Package Contents........................................................................\...

1. Introduction                                     _____________
Congratulations on purchasing the Broadband Router. This Broadband Router, is a high quality and reliable Internet 
routing device, enables multiple users to share the Broadband Internet connection through a Cable or DSL modem. 
Simply install the router, connect to Cable/DSL modem, and surf Internet without extra efforts. Acting as a 10/100Mbps 
4-port Ethernet switch as well, the router, with all ports supporting MDI/MDIX, allows you to...

and build-in static routing table. 
Configuration and Management 
µ Easy Setup: Users allow to configure Broadband Router from anywhere on the LAN via web browser. 
µ Remote Management: The Broadband Router can be managed from any PC on the LAN. 
µ UPnP Support: Universal Plug and Play feature. UPnP is supported by Windows ME or later. 
Security Features 
µ Password Protected Configuration: Optional password protection is provided to prevent unauthorized users from 
modifying the configuration data and...

On (Steady Amber)  WAN port is successfully connected  WAN  
Flashing  Data is being sent or received.  
 
Back Panel Connectors 
 
Button/port Description 
Button/port Description 
Reset  Reset configurations to default. Press the button and hold for 10 
seconds.  
1x, 2x, 3x, 4x  LAN Ports. Connect LAN systems with RJ-45 cable. 
WAN  WAN port. Connect DSL or Cable modem.  
PWR  Power jack. Connect with AC power adapter.  
 
1.4 System Requirements 
µ One or more PCs (desktop or notebook) with Ethernet...

2. PC Configuration                                   __________
User needs to configure TCP/IP network settings, Internet access configuration for each system within the Broadband 
Router’s LAN network.  By default, the Broadbnad Router acts as a DHCP server for server version of Windows, it 
automatically assigns IP address to each system when systems boot up.  For all non-server version of Windows, the 
default TCP/IP setting acts as a DHCP client.  If user chooses fixed IP addresses for client...

b) Select the “Internet Protocol (TCP/IP)” for the network card on your system, then click “Properties”, window 
below will appear. 
 
‧
If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. 
‧
If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure 
enter correct addresses in “IP Address” and “Subnet Mask” fields. 
‧
You must set Wireless Router’s IP address as “Default Gateway”. 
‧
If the DNS Server fields are...

 
 
b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear. 
 
‧
If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. 
‧
If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure 
enter correct addresses in “IP Address” and “Subnet Mask” fields. 
‧
You must set Wireless Router’s IP address as “Default Gateway”. 
‧
If the DNS Server fields are empty, select “Use the following DNS...

Checking TCP/IP Settings for Windows Vista 
a) Click “Start” Æ “Control Panel Æ  “Manage Network Connections” and right click “Local Area 
Connection” then select “Properties”, window below will appear. 
 
b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear. 
 
‧
If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. 
‧
If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure...