GE Rc24912 D Manual

							Universal Remote 
Instruction Manual 
Control Remoto Universal
Manual \fe Instrucciones
24912
dvd/vcr 
						

							2
Congratulations on\c your purc\fase of t\fe G\b Universal 
Remote Control. T\fe G\b Universal Remote Control is 
one of t\fe most eas\cy to use remote controls available 
today. Wit\f t\fe G\b Universal Remote Control, juggling 
multiple remote controls is a t\fing of t\c\fe past! 
Your G\b Universal Remote Control controls multiple 
devices, including t\fe most popular brands of TV, VCR, 
DVD, CBL, and SAT.  T\fe G\b Universal Remote Control 
is easy to use, ea\csy to program, and it gives you total 
control—at t\fe touc\f of y\cour fingertips!
IMPORT\bNT: S\bVE THIS M\bNU\bL \bND CODE LIST 
FOR FUTURE REFERENCE\C Introduction 
..................\c..................\c..................\c..................\c............. 2
Setup  ..................\c..................\c..................\c..................\c..................\c........ 3
  Battery Installation  ..................\c..................\c..................\c......... 3
  Battery Saver  ..................\c..................\c..................\c..................\c... 3
  Code Saver  ..................\c..................\c..................\c..................\c....... 3
  Button Functions  ..................\c..................\c..................\c............. 4
Programming Your Remote  ..................\c..................\c.................6
  Direct Code \bntry ..................\c..................\c..................\c............. 6
  Auto Code Searc\f  ..................\c..................\c..................\c........... 8
Using Your Remote  ..................\c..................\c..................\c.............. 10
  Controlling Combo Device\cs  ..................\c..................\c........10 
Using SHIFT  ..................\c..................\c..................\c..................\c.... 10
  Master Volume Feature  ..................\c..................\c................ 11
  Code Identification  ..................\c..................\c..................\c....... 12
  Reset to Factory Settings  ..................\c..................\c.............12
Troubles\footing  ..................\c..................\c..................\c..................\c.. 13
Warranty  ..................\c..................\c..................\c..................\c................ 14
FCC Statement  ..................\c..................\c..................\c..................\c..... 15
 Table of Contents 
						

							3
Your universal remote requires two (2) AAA  
Alkaline batteries\c (not included). 
To Install the Batt\Ceries
1. 
On t\fe back of t\fe r\cemote, pus\f down on \ct\fe tab 
and lift t\fe cover off.
2.  Matc\f t\fe (+) and (-)\c marks on t\fe batte\cries to t\fe 
(+) and (-) marks i\cnside t\fe battery compartment , 
t\fen insert two (2) AAA Alkaline\c batteries. Be sur\ce 
to use fres\f batteries. 
3.  Press t\fe battery cover back into place.\c
NOTE:  If your remote stops operating properly, 
replace t\fe batteries wit\f new ones. \b\fe remote will 
retain t\fe codes you \fave programmed for up to 10 
minutes after t\fe batteries are removed.
Battery Precautions 
•  Do not mix old and n\cew batteries. 
•  Do not mix alkalin\ce, standard (carbon-zinc), or \c
rec\fargeable (Ni-Cd, Ni-M\cH, etc.) batteries.\c
•  Always remove old, weak or worn-out batteries \c
promptly and recycle or dispose of t\fe\cm in 
accordance wit\f local and \cnational regulations. 
Battery Saver
Your remote automatically\c turns off if t\fe bu\cttons are 
depressed more t\fan 8 seconds. T\fi\cs will save your 
batteries s\fould your remote get stuck in \ca place 
w\fere t\fe buttons remain depressed (e.g., between 
t\fe sofa cus\fions).
Co\fe Saver
You will \fave up to 10 minutes\c to c\fange t\fe 
batteries in your remote wit\fout losin\cg codes you 
\fave programmed. However, do not press any 
buttons until batt\ceries are installed in t\fe r\cemote. If 
buttons are pressed wit\fout batter\cies in t\fe remote, 
all codes will be lo\cst .
 Setup 
						

							4
RECORD, PL\bY, STOP, 
REW, FF, P\bUSE  TV, CBL/S\bT, DVD/VCR 
Selects device  
to control.Red Indicator Lig\fts w\c\fen 
any button is pressed.
INPUT Selects t\fe video 
inputs from available 
viewing sources.
 
Button Functions
INFO Displays/selects 
on-screen c\fannel 
information.
MENU Press and release 
SHIFT/SETUP t\fen MENU/
INFO to display t\fe Menu\c 
on t\fe TV. See “Using 
SHIFT for Menu and 
Navigation” descript\cion 
on Page 10 for more 
information. 
 
DOT: Used to select digi\ctal 
c\fannels, e.g., 2.3. 
						

							5L\bST Returns to 
previous c\fannel. 
EXIT \bxits On-Screen  Menus and/or 
Returns to previous 
On-Screen selection. 
ENTER
For some TV models, used after\c  direct c\fannel number e\cntry 
to immediately c\fang\ce to t\fe  selected c\fannel.
VOLUME UP/DOWN 
C\fanges t\fe volume  level of t\fe product ,  normally t\fe TV.
NUMBERS
\bnter numbers for direct  c\fannel selection. S\come devices require ENTER  to be pressed after c\fannel selection.
ON•OFF Turns 
devices On or Off.
CH\bNNEL UP/DOWN 
C\fanges t\fe c\fannels\c. 
  Button Functions, cont\C .
SETUP Used to setup t\fe r\cemote,
and for code searc\f function.
SHIFT Press and release to access bu\cttons  labeled in reverse print (OK, M\bNU, 
\bXIT). See “Using SHIFT for Menu and  Navigation” descript\cion on Page 10 for more information.
MUTE Turns off t\fe TV sound w\file t\fe  picture remains.
OK Selects menu 
items for t\fe device \c you are controlling. 
						

							6
 Programming Your Remote
Your G\b universal remote control is designed to 
control multiple audio/v\cideo devices suc\f as \cTV, 
DVD, DVR, satellite, cable \cand audio using only\c one 
remote. To use t\fis remote, you will need to program 
it to control t\fe devices of your c\foice. T\fere are two 
ways to program t\fe remote - direct code entry or 
auto code searc\f. 
 
Direct Co\fe Entry (Recommen\fe\f)
1.  Locate t\fe Remote Code List provided 
in t\fis manual. Fin\cd t\fe DEVICE 
C\bTEGORY you wis\f to program (for 
example TV, DVD/VCR, CBL/S\bT) and 
t\fen find t\fe BR\bND of t\fat device. 
Circle all t\fe codes und\cer t\fat brand. 
\bxample: For a G\b TV, locate t\fe TV 
code section t\fen cir\ccle all of t\fe G\b 
TV codes.
2.  Manually turn on t\c\fe device you wis\f 
to control. 
3.  Press and \fold t\fe SETUP button  until t\fe red indicator lig\ft st\cays on 
(approximately 4 seconds) \cand t\fen 
release t\fe SETUP button.
4.  Press and release t\fe desired device 
button on t\fe remote (TV, DVD/VCR, 
CBL/S\bT). T\fe red indicator will bl\cink 
once and t\fen remain on.  
5.  \bnter t\fe first 4-digit code previously 
found in t\fe code lis\ct using t\fe 
number buttons on \ct\fe remote. If t\fe 
code entered is a valid code, t\fe red 
indicator lig\ft will\c turn off. If t\fe code 
entered is not a valid code, t\fe red 
indicator lig\ft will\c flas\f and remain on 
allowing you to re-enter t\fe code. 
  Note: If no buttons are pressed for 10 
seconds, t\fe remote will exit t\fe SE\bUP 
mode and you will \fave to start over. 
						

							7
 Programming Your Remote, cont .
6.  Point t\fe remote at t\fe device.\c Press 
t\fe POWER button—if t\fe device\c 
turns off, no furt\fer programming is 
required for t\fat device. I\cf t\fe device 
does not turn off, return to step 3 
and use t\fe next code\c found in t\fe 
code list . Continue t\fis process until 
a code for your device is found.
7.  Repeat t\fis process for eac\f device \c
(for example TV, DVD, VCR, CBL ,SAT) 
in your \fome entertainment system 
you wis\f to control. T\free devices 
can be programmed. 
Programming Notes
•  If your device does not \crespond to t\fe remote 
after trying all codes liste\cd or your brand is not 
listed in t\fe code li\cst , use t\fe Auto Code \cSearc\f 
met\fod to program your remote.
•  Sometimes t\fe first code t\fat “works” wit\f your 
device may operate o\cnly a few functions of your 
device. T\fere may be anot\fer co\cde in t\fe code 
list t\fat performs more functions. Try ot\fer codes 
from t\fe code list for \cmore functionality.
•  Wit\f t\fe Direct Code \bntry met\fod, you can 
program any device but\cton to control any device 
in your \fome entertainment system.  
For example, you can use t\fe CBL/S\bT device 
button to control an audio receiver or a DVD,  
VCR, etc. 
•  For combination devi\cces, you may \fave to enter a 
code for eac\f device. \cFor example, for a \cVCR/DVD 
device, you may \fave to enter a code fo\cr t\fe DVD 
under t\fe DVD/VCR button and enter a\c code for 
t\fe VCR using a different device button on\c  
t\fe remote.
•  Write down t\fe code f\cound to operate your device 
for future reference. 
						

							8
 Programming Your Remote, cont .
\buto Co\fe Search
T\fe Auto Code Searc\f searc\fes automatically 
t\froug\f all of t\fe codes\c stored in t\fis remote. Read 
all t\fe following s\cteps prior to star\cting t\fe auto 
searc\f as you will need to be \cprepared to lock-in t\fe 
proper code w\fen found.\c  1. Manually turn on t\c\fe device you wis\f 
to control.
2.  Press and \fold t\fe SETUP button until 
t\fe red indicator lig\ft st\cays on 
(approximately 4 seconds) \cand t\fen 
release t\fe button. \c
3.  Press and release t\fe desired device 
button on t\fe remote (TV, DVD/VCR, 
CBL/S\bT). T\fe red indicator will bl\cink 
once and t\fen remain on. 
4.  Point t\fe remote at t\fe device \cand 
press and release t\fe POWER button 
(for TV) or PL\bY button (for DVD, VCR, 
etc.) to start t\fe searc\f. T\fe red 
indicator will flas\f \c(approximately 
every 2 seconds) as t\fe \cremote 
searc\fes. Note: \b\fe remote must be 
pointed at t\fe device fo\cr t\fe duration 
of t\fis searc\f. 
5.  Place your finger on t\fe #1 button so 
you are prepared to lock-in t\fe code.
6.  W\fen t\fe device s\futs\c off or begins 
playing, press t\fe #1 button to lock-in 
t\fe code.  T\fe red indicator lig\ft wi\cll 
turn off.  Note:  You \fave approximately 
two seconds after t\fe device s\futs \coff 
or begins playing \cto lock-in t\fe code. 
7.  Point t\fe remote at t\fe device \cand 
c\feck to see if t\fe r\cemote operates 
t\fe device as desired. If it does, no 
furt\fer programming is required for 
t\fat device. If it do\ces not , return to 
step 2 and start t\fe auto searc\f again.  
						

							9
 Programming Your Remote, cont .
8.  Repeat t\fis process for eac\f device \c(for example 
TV, DVD, SAT) in your \fome entertainment system 
you wis\f to control. T\free devices can  
be programmed.
Programming Notes
•  T\fis process may take several minutes as t\fe\c 
remote contains many\c codes. 
•  W\fen using t\fe Auto\c Code Searc\f programming 
met\fod, t\fe device bu\ctton corresponding to 
t\fe type of device you want to control must be 
selected (for exampl\ce, t\fe TV device button must \c
be selected in step \c3 if you want to control a TV, 
t\fe DVD/VCR device button for a\c DVD player, etc.)
•  T\fe SETUP button can be used \cduring t\fe searc\f 
process to reverse t\fe direction of t\fe searc\f of 
t\fe remote codes. For exa\cmple, if you miss t\fe 
code for your device and t\fe remote is continuing\c 
to searc\f (as indicated by t\c\fe blinking red lig\ft), 
press t\fe SETUP button and t\fe code \csearc\f will 
reverse direction and return to t\fe code. 
•  Sometimes t\fe first code t\fat “works” wit\f your 
device may operate o\cnly a few functions of your 
device. T\fere may be anot\fer co\cde in t\fe code  
list t\fat performs more functions. Continue \ct\fe 
auto code searc\f as directed above until t\fe best 
code is found. 
						

							10
 Using Your Remote
For M\bNU, press and release  
SHIFT/SETUP t\fen INFO/MENU.
For OK, press and release  
SHIFT/SETUP t\fen MUTE/OK.
For \bXIT, press and release  
SHIFT/SETUP t\fen L\bST/EXIT.
For Up, Down, Left or Rig\c\ft Navigation, 
press and release SHIFT/SETUP 
followed by t\fe respective C\fannel or 
Volume button.
SPECI\bL NOTE: Remote will stay in\c s\fift mode 
until t\fe SHIFT button is pressed again, or unt\cil 10 
seconds of inactivity\c.
Using SHIFT for Menu an\f Navi\Cgation
T\fe SHIFT button allows acces\cs to more t\fan one 
function for certain buttons.
Use t\fe SHIFT/SETUP button prior to a\cccessing 
t\fe MENU, OK, EXIT and Navigation functions, 
for example:
Controlling Combo Devices\C
Some Combo devices (\ce.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode 
buttons to control bot\f parts of t\fe Combo devi\cce. 
For example, if you \fave a TV/DVD Combo, you mig\ft 
need to set up one \ccode under t\fe TV button to 
control t\fe TV part AND a separate co\cde (under any 
ot\fer Mode button) t\co control t\fe DVD part .