Garmin G1000 Manual

190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 85067
FLIGHT INSTRUMENTS
COURSE DEVIATION INDICATOR (CDI)
 NOTE:  During a heading change of greater than 105° with respect to the cour\
se, the CDI on the Arc HSI 
switches to the opposite side of the deviation scale and displays revers\
e sensing.
The Course Deviation Indicator (CDI) moves left or right from the course pointer along a lateral deviation 
scale to display aircraft position relative to the course.  If the course deviation...

Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A68
FLIGHT INSTRUMENTS
Changing navigation sources:
1) Press the CDI Softkey to change from GPS to VOR1 or LOC1.  This places the light blue tuning box over the 
NAV1 standby frequency in the upper left corner of the PFD.
2) Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2 or LOC2.  This places the light blue tuning 
box over the NAV2 standby frequency.
3) Press the CDI Softkey a third time to return to GPS.
Figure 2-25...

190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 85069
FLIGHT INSTRUMENTS
If	the	 same	 VOR/LOC	 navigation	 source	is	selected	 on	both	 PFDs,	 the	navigation	 source	annunciation	 turns	
yellow	on	both	 displays	 (unless	synchronized).		 Once	the	CDIs	 are	synchronized	 (CDI	Synchronization	 turned	
on), they remain synchronized until the setting is changed.  When turning on the G1000 for use, the system 
remembers the last CDI synchronization setting.
Synchronizing the CDIs:
1) Select...

Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A70
FLIGHT INSTRUMENTS
GPS CDI SCALING
When	GPS	is	the	 selected	 navigation	 source,	the	flight	 plan	legs	are	sequenced	 automatically	 and	
annunciations	 appear	on	the	 HSI	 for	the	 flight	 phase.	 	 Flight	phase	annunciations	 are	normally	 shown	in	
magenta, but when cautionary conditions exist the color changes to yellow.  If the current leg in the flight plan 
is	a	heading	leg,	HDG	LEG	is	annunciated	in	magenta	beneath	the...

190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 85071
FLIGHT INSTRUMENTS
Figure 2-28  Automatic CDI Scaling
2.0 nm
Enroute(Oceanic if >200 nm
from nearest air port)
0.3 nm
Missed
Approach
1.0 nm
Approach
1.0 nm
Te rm inal
1.0 nm
Term inal
0.3 nm
Depar ture
CDI Full-scale Deflection
Refer to accompan ying
approach CDI scaling figures
•	 Once	a	departure	procedure	is	activated,	the	CDI	is	scaled	for	departure	(0.3	nm).
•	 The	system	switches	from	departure	to	terminal CDI scaling (1.0 nm)...

Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A72
FLIGHT INSTRUMENTS
Figure 2-29  Typical LNAV and LNAV+V  Approach CDI Scaling
1.0 nm
2 nm350 ftangle set
by system0.3 nm
FA F
CDI Full-scale Deflection
CDI scale is set to the smaller of 0.3 nm
or an angle set by  the system
CDI scale va ries if VTF is activ ated
Figure 2-30  Typical LNAV/VNAV and LPV Approach CDI Scaling
1.0 nm
2 nmFAF
0.3 nm
course widthLanding
Threshold
CDI Full-scale Deflection
angle based
on database
inf...

190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 85073
FLIGHT INSTRUMENTS
OBS MODE
 NOTE: VNV is inhibited while automatic waypoint sequencing has been suspended.
Enabling	Omni-bearing	 Selector	(OBS)	Mode	suspends	 the	automatic	 sequencing	 of	waypoints	 in	a	GPS	
flight	 plan	(GPS	 must	be	the	 selected	 navigation	 source),	but	retains	 the	current	 “active-to”	 waypoint	as	the	
navigation	 reference	even	after	passing	 the	waypoint.	 	 OBS	is	annunciated	 to	the	 lower	 right	of	the...

Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A74
FLIGHT INSTRUMENTS
Enabling/disabling OBS Mode while navigating a GPS flight plan:
1) Press the OBS Softkey to select OBS Mode.
2) Turn a CRS Knob to select the desired course to/from the waypoint.  Press the CRS Knob to synchronize the 
Selected Course with the bearing to the next waypoint.
3) Press the OBS Softkey again to return to automatic waypoint sequencing.
As	the	 aircraft	 crosses	the	missed	 approach	 point	(MAP),...

190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 85075
FLIGHT INSTRUMENTS
2.2 SUPPLEMENTAL FLIGHT DATA
 NOTE:  Selecting the DFLTS Softkey turns off metric altimeter display, Hpa Baro Setting, the Inset Map, and 
wind data display.
In addition to the flight instruments, the PFD also displays various s\
upplemental information, including 
temperatures,	wind	data,	and	Vertical	Navigation	(VNV)	indications.
TEMPERATURE DISPLAYS
The	 Outside	 Air	Temperature	 (OAT)	is	displayed	 in	degrees...

Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A76
FLIGHT INSTRUMENTS
Changing temperature display units:
1) Select the AUX - System Setup Page on the MFD using the FMS Knob.
2) Press the FMS Knob to activate the cursor.
3) Turn the large FMS Knob to highlight the TEMP field in the Display Units box.
4) Turn the small FMS Knob to highlight either CELSIUS or FAHRENHEIT and press the ENT Key to confirm the 
selection.
5) To cancel the selection, press the FMS Knob or the CLR Key....