Fujitsu P42xha58 Users Manual

							E-31
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
CLEANING AND MAINTENANCE
Precautions
Be sure to remove the power plug from the receptacle before cleaning the display.
Be sure not to clean the display using a cloth dampened with volatile solvents, such as benzene or thinner.  Such solvents can harm the 
display’s cabinet, the filter at the screen front, and the remote control.  They can also cause paint to come off these sections.
Cleaning the Screen
Clean the screen gently with a soft cloth.
The screen surface is fragile.  Never attempt to clean it with a hard material, press on it forcefully, or tap it.
Cleaning the Cabinet and Remote Control
Use a soft cloth for cleaning.
If the cabinet or remote control is heavily stained, soak a soft cloth in a mixture of water  and detergent and squeeze it dry before wiping off the 
stains.  Use a soft, dry cloth for final cleaning.
Cleaning the ventilation grille
Remove dust from the ventilation grille in the rear of the main unit periodically with a vacuum cleaner as the accumulated dust can increase 
the internal temperature of the main unit causing machine failure or fire hazard.
In the event of problems with the display, check the following explanations before contacting your dealer for servicing.
BEFORE OBTAINING SERVICE
Problem Action
• Power does not turn ON. • Check whether the power plug is securely inserted into the receptacle.
• No pictures are displayed. • Check cables for disconnection.
• Check whether the power for all input equipment is ON.
• Check for connection to wrong terminals or for wrong input mode.
• Check whether the input mode display is colored pink. Special setup may have been 
made. Return to original setup or initialize the User adjustment value.
• Remote control does not function prop-
erly.• Check for incorrect battery orientation.
• Check for dead batteries. 
• Check for distance from the display.
• Check whether you are pointing the remote control transmitter properly at the display’s 
receiver.
• Check for any obstacle between the remote control and the display.
• The display makes a snapping sound. • This sound is produced when the cabinet expands or contracts due to variations in temper-
ature. This sound does not indicate that the display has a problem.
• The display makes a buzzing sound. • The display has fans to maintain the temperature of internal components at a constant 
level.  This sound is produced by the fan as it rotates. (Applies to models equipped with a 
fan)
• There are spots on the screen. • Check whether your AV equipment is affected by interference from automobiles, trains, 
high-voltage transmission lines, neon signs or other potential sources of interference.
• Degraded colors/tints • Check whether all picture adjustments have been properly made.
(See “Adjusting the Picture” on P. E-16–E-17.)
• Improper screen position/size • Check whether screen position and size have been properly adjusted.
(See “Adjusting Screen Position and Size” on P. E-21.)
• No audio • Check cables for disconnection.
• Check whether the proper audio input has been selected.
(See “Audio Input” on P. E-25.)
• If “Out of range” appears, the display is 
receiving a signal whose picture or signal 
cannot be reproduced by the display.
• The screen turns to black and white.• Signals that are not supported by this display have been input. Check which signals are 
supported. (See “MAIN SUPPORTED SIGNALS” on P. E-29.)
• If “Error message Condition 1” appears, 
the fan is defective. • Remove the power plug from the receptacle, and contact your dealer for repairs.
(Applies to models equipped with a fan)
• If “Error message Condition 2” appears, 
the display’s internal components are 
extremely hot.• Remove the power plug from the receptacle.  (You can turn the power back ON again 
when the components have cooled sufficiently.)  If the message appears again when you 
turn the power back on, remove the power plug from the receptacle, and contact your 
dealer for a repairs.
• If “Change refresh rate to 60Hz” appears.• The picture may get blurred with vertical frequency of other than 48.3-51.8 or 58.4-61.4 
(Hz). Change the setting of your PC, etc.
• If the power indicator lamp flashes red or 
green.• Remove the power plug from the receptacle, and inform your dealer about how the lamp 
flashed.
The power indicator lamp flashes differently depending on the type of problem.
Note
• Functions may not be available with some models and some device options.
7527_E.book  31 ページ  ２００６年９月５日　火曜日　午後９時３５分
 
						

							7527_E.book  32 ページ  ２００６年９月５日　火曜日　午後９時３５分