Fujitsu P42vha30 Users Manual

							English
E-29
* On-screen information disappears if you do not take any action for about 60 seconds.
*Functions may not be available with some models and some device options.
*The adjustment range varies with the display signal. You can adjust the display quality to the value you want within the adjustable range.
SETTING THE INPUT TERMINALS
•Selecting the settings of Video/S-video Input terminal
You can use this option to select the color format appropriate for the input signal.
Each time you press 
 or , one of the available modes appears in the following sequence:
Auto1: Automatically selects NTSC, PAL and SECAM.
Auto2: Automatically selects NTSC and M-PAL.
Other than Auto: You need to select a system appropriate to the input signal.
Press 
 to store.
•Selecting the settings of D-SUB Input terminal
You can use this option to select the signal system it will receive to D-SUB Input terminal.
(1) Select D-SUB Input and press 
.
D-SUB Input screen appears.
(2) Select the signal system to receive.
Each time you press 
 or , one of the available choices appears in the following sequence:
      RGB-PC 
 Decoder
RGB-PC: For using RGB for PC
Decoder: For using digital broadcast tuner
(3) Press 
 or  to select Mask.
(4) Select Decoder by FUNCTION to set up Mask.
Each time you press 
 or , one of the available choices appears in the following sequence:
Off: Does not mask.
Number: Masks the fringe (top, bottom, right and left) of the screen by the number of pixels
specified.
(5) Press 
 to store.
•Selecting the settings of DVI-D Input terminal
You can select the signal method input to the DVI input terminal.
Each time 
 or  is pressed, the setting is changed.
DVI1 
 DVI2
DVI1: Used when connecting to a PC.
DVI2: Used when connecting to a DVD player or digital tuner.
Press 
 to store.
* Set according to the signal method before connecting peripheral device.
“D-SUB Input” selection screen1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
This fringe part is masked.

&1MBTNBXJEF
	
03.10.3, 0:19 PM Page 29EPCF
1BHF.BLFS
+11$
 
						

							E-30
OTHER ADJUSTMENTS (FEATURES MENU) (Continued)
OTHER SETTINGS
DPMS for other then RGB1
You can use this option to select the amount of time before the DPMS function starts.
DPMS (which stands for “display power management signaling”) allows the display to maintain an
automatic power saving function.
This function causes on-screen information to disappear until the next input operation, if the power
is ON and the display has not received any signals for the predetermined period of time.  When
DPMS is active, the power indicator lamp turns orange.
(1) Select DPMS and press 
.
DPMS screen appears.
(2) Press 
 or  to select Time.
(3) Each time you press 
 or , one of the available choices appears in the following sequence:
Off: Disables DPMS
Number: Approximate time before DPMS starts.  (Unit: minutes)
* The power indicator lamp turns orange while the DPMS is ON.
* The power turns ON automatically when the display receives a signal.
(4) Can specify background colour.
Press 
 or  to select background colour.
Each time you press 
 or , one of the available choices appears in the following sequence:
Black 
 White
Black: Mutes images in Black background.
White: Mutes images in White background.
* Switches approx. 20 seconds after the display stops receiving signals.
 (5) Press 
 to store.
• Selecting input terminals (Audio Input)
You can use this option to select the available terminals to receive the audio from input equipment.
(1) Select “Audio Input” and press 
.
The “Audio Input” selection screen will appear.
(2) Press 
 or  to select video input terminal.
(3) Select a related audio input terminal.
Each time you press 
 or , one of the available choices appears in the following sequence:
No audio: No audio in the corresponding mode.
Audio 1-3: Selects Audio 1 through 3 for receiving audio in the corresponding mode.
* Repeat steps (2) and (3) for each piece of input equipment.
(4) Press 
 to store.
*Audio Input menu will not be displayed when No Audiois selected.DPMS selection screen
“Audio Input” selection screen

&1MBTNBXJEF
	
03.10.3, 0:19 PM Page 30EPCF
1BHF.BLFS
+11$
 
						

							English
E-31
•Minimizing phosphor burn-in (Screen Orbiter) for RGB
You can use this option to move the screen position to minimize phosphor-induced “burn-in”.
Follow the steps below.
(1) Select “Screen Orbiter” and press 
.
The “Screen Orbiter” setting screen will appear.
(2) Press 
 or  to select “Mode/Time”.
(3) Select a desired pattern.
Each time you press 
 or , one of the available choices appears in the following sequence:
Off: Disables Screen Orbiter.
Time: Moves the pattern approximately every one hour.
Mode: Moves the pattern when the power is turned ON or when you switch between modes.
(4) Press 
 or  to select “Moving Area”.
(5) Press 
 or  to select the range for moving the pattern.
Each time you press 
 or , one of the available choices appears in the following sequence:
Min.: Pattern moves in small range. (About 5 pixels)
Std.: Pattern moves in moderate range. (About 10 pixels)
Max.: Pattern moves in wide range. (About 15 pixels)
(6) Press 
 to store.
*When the Screen Orbiter function is operated in RGB1 mode, some letters at the top, bottom,
right or left of the screen may be missed.
•Setting RGB Input Signal Compulsorily (Direct Setting) for RGB
You can use this option to switch the setting for RGB input signal.
Each time you press 
 or , one of the available choices appears in the
following sequence:
 For RGB1 mode:
 For RGB2 mode:
       
Auto: The optimum display is obtained automatically for input signals.
Others: The optimum resolution setting is fixed for each signal.
Press 
 to store.
* In Auto mode, the resolution of VGA, WVGA, 480P, XGA, WXGA, SXGA and SXGA
+ may not
be automatically distinguished. Switch to the fixed display when the image is not displayed
properly.“Screen Orbiter” setting screen
* On-screen information disappears if you do not take any action for about 60 seconds.
*Functions may not be available with some models and some device options.
*The adjustment range varies with the display signal. You can adjust the display quality to the value you want within the adjustable range.

&1MBTNBXJEF
	
03.10.3, 0:19 PM Page 31EPCF
1BHF.BLFS
+11$
 
						

							E-32
* On-screen information disappears if you do not take any action for about 60 seconds.
*Functions may not be available with some models and some device options.
*The adjustment range varies with the display signal. You can adjust the display quality to the value you want within the adjustable range.
•Specifying RGB Input Signal (Code Setting) for RGB2
Normally, use this option in Auto mode.
•Displaying white over entire screen (White Screen)
You can use this option to display white over the entire screen to minimize phosphor burn-in.
Each time you press 
 or , one of the available choices appears in the following sequence:
On 
 Off
Off: Does not display white.
On: Displays a white screen immediately.
Press 
 to store.
•Setting Exhibition Mode (Exhibition Mode)
You can use this option to display the enhanced contrast, which is most suitable for the use by
unspecified persons.
Each time you press 
 or , one of the available choices appears in the following sequence:
On 
 Off
On: Sets up Exhibition mode.
Off: Sets up normal mode.
Press 
 to store.
* In Exhibition mode, the display returns to the original setting in about 5 minutes even if the
adjustment is changed.
* The setup will be cancelled when removing the power plug from the receptacle.
•Displaying System Status (Information)
Displays system operation status.
Select “Information” and press 
.
The “Information” screen will appear.
Mode: Input mode appears at the upper right corner of the screen.
Freq. Scan Mode: Frequency scanning
Input Signal: Video mode
Input Sync.: Signal type
Freq.: Synchronized signal frequency, polarity
Preset No.: RGB code numberInformation screen (Video Mode)
OTHER ADJUSTMENTS (FEATURES MENU) (Continued)
Information screen (RGB Mode)

&1MBTNBXJEF
	
03.10.3, 0:19 PM Page 32EPCF
1BHF.BLFS
+11$
 
						

							English
E-33
INITIALIZATION OF USER ADJUSTMENT VALUE (FACTORY DEFAULT)
1
“FACTORY DEFAULT” selected in the
main menu screen
Displays the message of whether to
proceed the initialization
Displays the message of having
completed the initialization
You can restore the values of the adjustment/setting made in the MENU to factory settings.
PICTURE  POSITION/SIZE  AUDIO  FEATURES  FACTORY DEFAULT
3
4
5
Press .
The main menu screen will appear.
Press  or  to select “FACTORY
DEFAULT”.
Each time you press  or , one of the available
menus appears in the following sequence:
The FACTORY DEFAULT Menu screen will
appear.
Press .
•Displays the message of whether to proceed
with the initialization.
Press  or  to select the
Yes.
Press 
.
•The message of having completed the
initialization will be displayed after initializing.
Press   when you finish.
2

&1MBTNBXJEF
	
03.10.3, 0:19 PM Page 33EPCF
1BHF.BLFS
+11$
 
						

							E-34
Action
•Check whether the power plug is securely inserted into the receptacle.
•Check cables for disconnection.
•Check whether the power for all input equipment is ON.
•Check for connection to wrong terminals or for wrong input mode.
•Check whether the input mode display is colored pink.Special setup may have been
made. Return to original setup or initialize the User adjustment value.
•Check for incorrect battery orientation.
•Check for dead batteries.
•Check for distance from the display.
•Check whether you are pointing the remote control transmitter properly at the display’s
receiver.
•Check for any obstacle between the remote control and the display.
•This sound is produced when the cabinet expands or contracts due to variations in
temperature.  This sound does not indicate that the display has a problem.
•The display has fans to maintain the temperature of internal components at a constant
level.  This sound is produced by the fan as it rotates.
•Check whether your AV equipment is affected by interference from automobiles, trains,
high-voltage transmission lines, neon signs or other potential sources of interference.
•Check whether all picture adjustments have been properly made.
(See “Adjusting Pictures” on P. E-19–E-21.)
•Check whether screen position and size have been properly adjusted.
(See “Adjusting Screen Position and Size” on P. E-22–E-23.)
•Check cables for disconnection.
•Check whether you have selected “No Audio” for the “Audio Input” setting.
Check whether the proper audio input have been selected.
(See “Features” on P. E-30.)
•Input proper signals.
Make sure to check the vertical frequency of the input signal.
(See the user’s manual (1/2))
•Remove the power plug from the receptacle, and contact your dealer for repairs.
•Remove the power plug from the receptacle.  (You can turn the power back ON again
when the components have cooled sufficiently.)  If the message appears again when you
turn the power back on, remove the power plug from the receptacle, and contact your
dealer for a repairs.
•The picture may get blurred with vertical frequency of other than 48.3-51.8 or 58.4-61.4
(Hz). Change the setting of your PC, etc.
•Remove the power plug from the receptacle, and inform your dealer about how the lamp
flashed.
The power indicator lamp flashes differently depending on the type of problem.
CLEANING AND MAINTENANCE
Problem
•Power does not turn ON.
•No pictures are displayed.
•Remote control does not function properly.
•The display makes a snapping sound.
•The display makes a buzzing sound.
•There are spots on the screen.
•Degraded colors/tints
•Improper screen position/size
•No audio from external speakers
•No audio
•If “Out of range” appears, the display is
receiving a signal whose picture or signal
cannot be reproduced by the display.
•The screen turns to black and white.
•If “Error message Condition 1” appears,
the fan is defective.
•If “Error message Condition 2” appears,
the display’s internal components are
extremely hot.
•If “Change refresh rate to 60Hz” appears,
•If the power indicator lamp flashes red or
green.
HANDY TIPS
In the event of problems with the display, check the following explanations before contacting your dealer for servicing.
Precautions
Be sure to remove the power plug from the receptacle before
cleaning the display.
Be sure not to clean the display using a cloth dampened with
volatile solvents, such as benzene or thinner.  Such solvents can
harm the display’s cabinet, the filter at the screen front, and the
remote control.  They can also cause paint to come off these
sections.
Cleaning the Screen
Clean the screen gently with a soft cloth.
The screen surface is fragile.  Never attempt to clean it with a hard
material, press on it forcefully, or tap it.
Cleaning the Cabinet and Remote Control
Use a soft cloth for cleaning.
If the cabinet or remote control is heavily stained, soak a soft cloth
in a mixture of water  and detergent and squeeze it dry before
wiping off the stains.  Use a soft, dry cloth for final cleaning.
Cleaning the ventilation grille
Remove dust from the ventilation grille in the rear of the main unit
periodically with a vacuum cleaner as the accumulated dust can
increase the internal temperature of the main unit causing machine
failure or fire hazard.
*Functions may not be available with some models and some device options.

&1MBTNBXJEF
	
03.10.3, 0:20 PM Page 34EPCF
1BHF.BLFS
+11$