Fujitsu P23t 6 Ips Operating Manual

							Getting started
►Connect one of the connectors of the data cable to the D-SUB socket or the DVI-D socket or the
DP socket of the monitor and secure the plug connection by tightening the retaining screws.
If you are using a display port data cable, you must switch the 0 W switch to
the Basic setting. If you are only using a DVI or VGA data cable, you can switch
the 0 W switch to the ECO setting to activate the 0 W standby.
The monitor automatically detects the input when only one signal source is connected.
► Insert one connector of th e audio line in the AUDIO IN socket on the monitor
and make sure it is proper ly engaged.
► Plug the power cable supplied into the power connector of the monitor.
► Plug the supplied USB ca ble into the USB IN socket and the other end of
the cable into a USB sock et of the computer.
Connect the USB keyboard and USB mouse directly to the PC, as the USB connector
socket of the monitor is switched off in energy-saving mode.
► Secure the cover over the connections.
A lock (Kensington Lock) can be mounted in the security slot to protect the monitor
against theft. A Kensington lock is not supplied with the monitor.
Connecting cables to the computer
Information on the computer connections and interfaces is contained in the
operating manual for your computer.
►Connect the data cable to the (active) monitor port on the computer and secure
the plug-in connection by tightening the safety screws.
► Insert the other plug of the audio cable in the audio output of the computer.
► Plug the power connector of the monitor into a properly grounded mains outlet.
► Plug the power connector of the computer into a properly grounded mains outlet.
If your computer has two monitor ports (onboard screen controller and separate
graphics card), the monitor port for the s eparate graphics card is active as standard.
Fujitsu Technology Solutions 17
 
						

							Operation
Operation
Switching the device on and off
123
12
1 = Switch On/Off
2 = Power supply indicator 3=0Wswitch
The colour of the LED indicator changes as follows: LED indicator Status
blue Monitor and computer are switched on (normal mode).
green
Monitor and computer are switched on (ECO mode).
orangeMonitor is not receiving a video signal or is in power saving mode.
does not light upMonitor is switched off (or is in 0W power-saving mode).
Theswitchsetting0ofthe0Wswitch(3)onthereversesideactivatesthe
ECO power- saving mode (0 W operating mode) and the switch setting I
switches to the BASIC power saving mode < 1 W. This setting is required for
the DP data cable. In some PCs, it can, however, also be necessary for VGA
or DVI if the screen remains unlit in the 0 W operating mode.
► SwitchthedeviceonagainwiththeON/OFFswitch(1).
18 Fujitsu Technology Solutions
 
						

							Operation
Notes on power management
If your computer is equipped with power management (power-saving mode), the monitor can fully
support this function. Here the monitor does not distinguish between the individual energy-saving
modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of
immediately switching into the mode with the highest energy-saving effect.
Stage Operation Power-saving mode (0 W switch)
Normal ECO ECO (0) BASIC (|)
Power supply
indicator Lights up blue Lit green is unlit illuminated
orange
DisplayMax. brightness
typ. 175 cd/m2unlitUnlit
Typical power
consumption
(without USB and
audio) 35 W
27 Wreduced to 0 W reduced to < 1 W
If the computer detects inactivity (no input) it sends an appropriate signal to the monitor
to reduce the power consumption (power saving mode). The power indicator of the
monitor changes colour to show the change in status. The ECO operating mode and
BASIC power-saving mode are the preset factory defaults.
Once an input is made at the computer the screen contents are restored.
For detailed information on how energy -saving mode operates, please refer to
the operating manual or technical manual of the computer.
Fujitsu Technology Solutions 19
 
						

							Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor setti ngs with the buttons
of the control panel
The buttons of the control panel have two functions. If the OSD menu is
activated, a description of the current function of the buttons is displayed
directly above the buttons at the edge of the screen. If the OSD menu is not
activated, you can make the following settings directly:
12 3
1 = Buttons for the OSD menu (On
Screen Display)
2 = ON/OFF switch 3 = Power supply indicator
Select OSD language
If one of
the buttons is being pressed for the
firsttimefortheOSDmenu,the
selecti on screen for the language is displayed:
► Press the
ECO/or theINPUT/button to select the required language.
► Press the
MENU/button to confi rm your entries or theAUTO/button to cancel the process.
After selecting the OSD language for the first time, you can change
it at any time in the OSD.
Performing auto-adjustment of the monitor
► Press theAUTO/button for about 1 second.
The
Auto Processing message appears
Picture quality and position are set to optimum values for your system.
20 Fujitsu Technology Solutions
 
						

							Operation
Selecting input signal (D-SUB/DVI-D/HDMI)
►Press theINPUT/buttontocallupthe Input selectsettings window.
► Press the
ECO/or theINPUT/button to select the desired
monitor connection (VGA, DVI or DP).
► Press the
MENU/buttontocon firm your selection or theAUTO/button to cancel the process.
This setting window can also be called up when the OSD menu is locked.
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
► Press and hold the
MENU/button for a few seconds while you switch
on the monitor using the ON/OFF switch.
The message OSD locked / unlocked is displayed.
Please proceed in the same manner to release the locked OSD menu again.
Activate/deactivate ECO operating mode
The power consumption of the device can be decreased by reducing
the brightness of the picture.
► Press the
ECO/button to switch the ECO operating mode on or off.
The message ECO Mode ein orECO Mode off appears.
If the ECO operating mode is activated, the following OSD settings are changed:
Mode Office
Colour 6,500 K
Brightness reduced
After the ECO operating mode is switched off, the b rightness previously set by the user is restored.
Fujitsu Technology Solutions 21
 
						

							Operation
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press and hold the
ECO/andINPUT/buttons at the same time for a few seconds.
The message Power button loc ked / unlocked
is displayed.
Proceed in the same way to r elease the locked ON/OFF switch again.
22
Fujitsu Technology Solutions
 
						

							Operation
Changing the monitor settings using the OSD menu
With the buttons on the control panel, you can call up and use the integrated
OSD (On-Screen Display) menu.
The English menu names are used in the following description (default setting).
►Press theMENU/button to activate the OSD menu.
The main menu appears, with icons for the setting functions.
The first symbol, ( Brightness/Contrast ), is highlighted and the associated functions
are visible in the right-hand menu field.
► Press the
ECO/or theINPUT/button to highlight another icon (e.g. Image adjust).
► Press the
MENU/button to select the highlighted icon.
The Image adjust settings window is displayed.
► Press the
AUTO/button to exit the main menu.
Fujitsu Technology Solutions 23
 
						

							Operation
►Press theECO/orINPUT/button to highlight another function.
► Press the
MODE/button or the/button to change the setting.
► Press the
ECO/or theINPUT/button to highlight another function.
► Press the
MENU/button to save the change or press theAUTO/button
to exit the function without making any changes.
If you want to change other settings, select the corresponding function from the OSD
main menu . All possible adjustments of the main menu are described in the following.
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
24
Fujitsu Technology Solutions
 
						

							Operation
Adjusting the brightness and contrast
Call up theBrightness/Contrast setting window
Brightness
Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast
Set the contrast of the display
With this function you modify the contrast of bright colour tones.
Black levelSet the brightness of the display
With this function you modify the contrast of dark colour tones.
Auto BrightnessAutomatic brightness control
This function is used to automatic ally control the brightness of the
background lighting using the light sensor.
On = The brightness is adjusted according to the ambient brightness
Off = The brightness is adjusted manually by the user
Auto level
Adjust the signal level
With this function you can automatically set the contrast.
The function is executed with the
button.
If the contrast is set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.
Selecting the application mode
Call up theMode
setting window
D mode
Setting forDICOM simulation (the values for colour and ACR are locked:
Colour = 75 00K, ACR = off)
Of
fice
Office presets (the settings for colourandsharpness canbeadjusted)
Photo
Photo presets (colour,sharpness, saturation,ACR )
Vi d e o
Video presets (
colour,sharpness, saturation,ACR )
ACR = Dynamic contrast (on / off)
Fujitsu Technology Solutions 25
 
						

							Operation
Adjusting the picture size and position
Call theImage adjust setting window
Phase
Eliminate picture disturbance
With this function youfine-tune your monitor to eliminate picture disturbance.
Clock
Set synchronisation
With this function you adjust the picture width to eliminate vertical picture
disturbances.
H-Position
Adjust the horizontal position
With this function you move the picture to the left or to the right.
V-PositionAdjust the vertical position
With this function you move the picture up or down.
SharpnessAdjust the sharpness of the picture for the PhotoandVi d e o modes.
Saturation
Adjust the saturation for the PhotoandVideo modes.
Expansion
Adjust the picture size
Full screen= selection of full screen mode
Keep aspect = maximum picture size without distortion (only for PC image)
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Setting colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in K (= Kelvin). You can choose between
sRGB,6500 K, 7500 K,9300 K, NativeandCustom Colour .
The options sRGB,Native andCustom colour are only available in the Office
setting mode.
In the user-de fined setting you can change the colour ratios of the basic
colours (red, green, blue) as required.
26 Fujitsu Technology Solutions