Fujitsu A19 5 Eco Operating Manual

Operation
Operation
Switching the device on and off

 

1 = Buttons for the OSD menu (On-Screen
Display)
2 = Power supply indicator
3 = ON/OFF switch
Press the buttons upwards from below.
The colour of the LED indicator changes as follows:
LED indicator Status
Blue
Monitor and computer are switched on (normal mode).
Not lit
The monitor is switched off (or is in power saving mode - power
consumption in standby and off mode≤1W).
►Switch the device on using the ON/OFF switch.
Only switch on the computer...

Operation
Notes on power management
If the computer is equipped with power management(power-saving mode), then this function
can be fully supported by the monitor. The monitor does not distinguish between the individual
energy-saving modes used by the computer (standby mode, suspend mode and OFF mode), as
it is capable of immediately switching into the mode with the highest energy-saving effect.
Level
OperationPower saving mode
Normal
Power supply indicator Blue light
Orange light
Monitor Max. brightness...

Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor settingswith the buttons
of the control panel
The buttons of the control panel have two functions. With the OSD menu not
activated, you can make the following settings directly:
1 = Buttons for the OSD menu (On
Screen Display)
2 = Power indicator3 = ON/OFF switch
Performing auto-adjustment of the monitor
►Press...

Operation
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the
SELECT/MENUbutton for a few seconds while you switch
on the monitor with the ON/OFF switch.
TheAction was executedmessage appears.
Please proceed in the same manner to release the locked OSD menu again.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press and hold the...

Operation
►Press theSELECT/MENUbutton to
activate the OSD menu.
The main menu appears, with icons
for the setting functions.
Thefirst icon, (Brightness/Contrast), is
highlighted and the associated functions are
visible in the right-hand menufield.
►Press the Forwards /button or the
Back /button to highlight another
icon (e.g.Image adjust).
►Press the
SELECT/MENUbutton to
select the highlighted icon.
TheImage adjustsetup window will
be displayed.
►Press the Forwards /
button or the
Back /button to...

Operation
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
Adjusting the brightness and contrast
Call up theBrightness/Contrastsetting window
Brightness
Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast
Set the contrast of the display
With this function you modify the...

Operation
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Setting the colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in Kelvin (K). You can choose between
sRGB,6500 K,7500 K,9300 K,NativeandCustom Colour.
In the user-defined setting you can change...

Operation
Configuring function settings in the Advanced menu
Open theAdvancedsettings window
DDC/CI
Activate/deactivate the DDC/CI function
On= The DDC/CI function is activated (standard setting)
Off= The DDC/CI function is deactivated
Resolution Notifier
Monitor information. The optimum resolution for this monitor is 1280 x 1024
pixels.
When the function is active (On), a message will appear on the monitor after
approx. 30 seconds if a different resolution is set.
Change the resolution to 1280 x 1024 to...

Notes on ergonomic colour adjustment
Notes on ergonomic colour adjustment
If you select colours for the monitor in your application programmes,
take note of the information below.
The primary colours blue and red on a dark background do not produce the minimum
required contrast of 3:1 and are therefore not suitable for continuous text and data entry.
When using several colours for characters and background and giving the primary colours full
modulation, you can obtain very suitable colour combinations...

Troubleshooting
Troubleshooting
Should an error occur,first check the following points. If the distortion is still not eliminated,
the monitor should, if possible, be checked on another computer.
If you cannot solve the problem, please contact our Service Desk.
Having this problem? Check the following points:
No screen display
Power indicator does not light up►Check whether the ON/OFF switch on the
monitor is switched on.
►Check whether the power cableon the
monitor is connected correctly.
►Check whether...