Fujifilm Camera X30 Owners Manual

Connect the supplied USB cable as shown and turn the printer on.1. 
Turn the camera on. [USB] will be displayed in the monitor, followed by the PictBridge
display.2. 
Printing Pictures via USB
002D0020 0032003400310020 002D  

Press the selector left or right to display a picture you wish to print.
To print one copy of the current picture, proceed directly to S tep 3.1. 
Press the selector up or down to choose the number of copies (u p to 99). Repeat steps 1–2
to select additional pictures.2. 
Press  [MENU/OK]  to display a confirmation dialog.3. 
Press [MENU/OK]  to start printing.4. 
If no pictures are selected when the  [MENU/OK] button is pressed, the camera will print
one copy of the current picture.
Printing the Date of...

To print the print order created with [PRINT ORDER (DPOF)] in the playback menu.
In the PictBridge display, press  [DISP/BACK] to open the PictBridge menu.
1. 
Press the selector up o r down to highlight [PRINT DPOF].2. 
Press [MENU/OK]  to display a confirmation dialog.3. 
Press [MENU/OK]  to start printing.4. 
Printing Pictures via USB
002D0020 0032003400330020 002D  

During Printing
A message is displayed during printing. Press [DISP/BACK] to cancel before  all pictures are
printed (depending on the printe r, printing may end before the current picture has printed). If
printing is interrupted, turn the camera off and then on again.
Disconnecting the Camera
Confirm that the above message is not displayed and turn the cam era off. Disconnect the USB
cable.
Pictures can be printed from internal memory or a memory card t hat has been formatted
in the camera.
When pictures...

To show pictures to a group, connect the camera to a TV using an HDMI cable (available
separately from third-party suppliers; note that the TV can only be used for playback, not
shooting).
Turn the camera off.
1. 
Connect the cable as shown below.
Insert into Micro HDMI connector
Insert into HDMI connector
Use an HDMI cable no more than 1.5  m (4.9 ft.) long.
Be sure the connectors are fully inserted.
2. 
Tune the television to the HDMI input channe l. See the documentation supplied with the
television...

Shoe-mounted flash units
Power Supplies
Remote Releases
Stereo microphones
Other
Website of the country or region of purchase
For more information, visit the w ebsite of the country or region of purchase (the new window will
open).
Check the website »
Accessories
002D0020 0032003400360020 002D  

EF-20
EF-42
EF-X20This clip-on flash unit  (powered by two AA b atteries) has a Guide Number of 20/65
(ISO 100, m /ft.) and supports TTL flash control. The flash head c an be rotated
upwards 90° for bounce lighting.
This clip-on flash unit  (powered by four AA batteries) has a Guide Number of
42/137 (ISO 100, m /ft.) and supports TTL flash control and auto  power zoom in the
range 24–105 mm (35 mm format eq uivalent). The flash head can be rotated 90°
up, 180° left, or 120° right for bounce lighting.
This...

NP-95
BC-65N
Rechargeable Li-ion batteries
Battery chargers
NP-95
Additional large-capacity NP-95 rechargeable batteries can be p urchased as
required.
BC-65N
Replacement battery chargers can  be purchased as required. At +20 °C/+68 °F, the
BC-65N charges an NP-95  in about 240 minutes.
For more information, visit the w ebsite of the country or region of purchase (the new window will
open).
Check the website »
Power Supplies
002D0020 0032003400380020 002D  

RR-90
Remote Releases RR-90
Use to reduce camera shake or keep the shutter open during a ti me exposure.
An optional RR-90 remote release can be used for long time-expo sures.
Remote Releases
002D0020 0032003400390020 002D  

Third-Party Remote Releases
Electronic releases from third-party suppliers can be connected via the microphone /remote
release connector.
A confirmation dialog will be displayed when a third-party relea se is connected; press
[MENU/OK] and select  [REMOTE] for [MIC/REMOTE RELEASE] .
For more information, visit the w ebsite of the country or region of purchase (the new window will
open).
Check the website »
Remote Releases
002D0020 0032003500300020 002D