Ford Vcm 2 User Manual
Here you can view all the pages of manual Ford Vcm 2 User Manual. The Ford manuals for Automobile Accessories are available online for free. You can easily download all the documents as PDF.
Page 11
V C M I I H A R D W A R E M A N U A L 9 Figure 2: VCM II Rubber Boot Removed Exposing Recovery Mode Switch Figure 3: VCM II Update Pop-Up Window
Page 12
V C M I I H A R D W A R E M A N U A L 10 Troubleshooting sers should perform the following basic checks to d etermine if they can resolve any problems with the VCM II unit. If the VCM II is sti ll inoperable after performing the checks, contact your regional technical support for assistance. Troubleshooting Table Problem Symptoms Checks & Possible Causes VCM II will not power On (No LEDs turn On) Make sure that secure cable connections are made...
Page 13
V C M I I H A R D W A R E M A N U A L 11 VCM IIs Power LED is on, but no 1 second beep USB issue. Attempt to recover the software (refer to How To Factory Reset Your VCM II section) on the VCM II If VCM II error persists, contact your regional techni cal support VCM IIs Error LED is red immediately after it is booted Reboot the PC Attempt to recover the software (refer to How To Factory Reset Your VCM II section) on the VCM II If recovery fails, attempt a...
Page 14
V C M I I H A R D W A R E M A N U A L 12 automatically be enabled and the Power LED will stop blinking and stay illuminated If VCM II wireless interface problem persists when the ambient temperature returns to its operating range, contact your regional technical support VCM IIs Power LED blinks continuously after being powered using the DLC cable Verify the ambient temperature is within the acceptab le operating range for the VCM IIs wireless interface: 0°C to 50°C...
Page 15
V C M I I H A R D W A R E M A N U A L 13 VCM II Technical Specifications Voltage, Current and Power Requirements 5 – 32 VDC, 750 mA (max), 2.0 Watts @ 12 VDC Note: protected against reverse battery polarity Power Sources - 12 & 24 volts vehicle power (using DLC cable) - USB power (5 volts from a PC USB port) - External AC/DC 12 volts adapter (not included in VCM II kit ) Vehicle Protocols - CAN (High & Medium Speed) - FTCAN - SCP (SAE J1850 PWM) - SAE J1850 VPW -...
Page 16
V C M I I H A R D W A R E M A N U A L 14 Care and Maintenance eriodically the VCM II, its connectors and cables shoul d be inspected and cleaned after usage. Make sure that the VCM II is NOT connected to any power source (i.e., vehicle DLC or PC USB port) during cleaning. Follow the cleaning tips outlined below: Always use water or a mild detergent solution appl ied to a soft cloth to clean the VCM II unit and dry thoroughly Never use petroleum base...
Page 17
V C M I I H A R D W A R E M A N U A L 15 VCM II (ES6516) Product Warranty The VCM II (ES6516), cables, adapters and accessories are warranted by Vetronix Corporation to the original consumer, to be free of defects in mate rial or workmanship under normal use for a period of two years. Some countries may have agreements that e xtend beyond the two year period. Contact your regional technical support regarding extended Ha rdware Protection. The warranty period is from the date of...
Page 18
V C M I I H A R D W A R E M A N U A L 16 SELLER, ITS SUPPLIERS OR SERVICE PROVIDERS. ALL IMP LIED OR STATUTORY WARRANTIES TO THE EXTENT THAT THEY CANNOT BE EXCLUD ED ARE LIMITED TO THE EFFECTIVE PERIOD OF THE EXPRESS WARRANTY SET FORTH HEREIN. IF THE PRODUCT IS DEFECTIVE IN MATERIALS OR WORKMANSHIP, BUYER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE. H OWEVER IF THAT REMEDY FAILS OF ITS ESSENTIAL PURPOSE, SELLER RESERVES THE RIGHT TO REFUND THE...