Flir ThermovisionNavigator II Installation Manual

Navigator™ II
IN stallat Io N  M aNU al
F o r  stat Ic  a Nd  Pa N/t I lt  co NFI gUr at Io N s  

Document Number: 432-0001-00-12, rev 100
© FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole or in part, 
may be copied, photocopied, translated, or transmitted to any electronic medium or machine readable 
form without the prior written permission of FLIR Systems, Inc.
Names  and  marks  appearing  on  the  products  herein  are  either  registered  trademarks  or 
trademarks  of  FLIR  Systems,  Inc.  and/or  its  subsidiaries.  All  other  trademarks,  trade...

Pa N / tIlt co NFIgUrat Io N 
Introduction 
Your Navigator II comes with the camera head, a cable that goes from the camera head to the Joystick 
Control Unit (JCU) and Monitor, the JCU and the mounting hardware described below.
Installation
Caution!  The Navigator II should be installed by a factory-authorized installer. Incorrect installation could 
void your warranty.
DO  NOT  separate  the  camera  from  its  Pan/Tilt  base  during  installation.  Doing  so  will  void   
your warranty.
c amera...

Figure 1Figure 2
Figure 3
(for Reference Only)Figure 4 

Joystick control Unit Mounting
Caution!   Changing  the  wiring  configuration  of  the  Navigator  II  or  attempting  to  utilize  controllers  or   
wiring harnesses other than those supplied by FLIR may cause permanent damage to the unit and may 
void the warranty.
Caution!   Do  not  connect  the  camera  to  any thing  other  than  12  VDC  power.  Operating  the  camera 
outside  of  the  specified  input  voltage  range  or  the  specified  operating  temperature  range  can  cause 
permanent...

Figure 6(for Reference Only) 

statIc co NFIgUrat Io N
Thank  you  for  buying  your  new  Navigator  II!  If  you  need  help  during  the 
installation  process,  call  888.747.3547  to  speak  with  one  of   
FLIR’s Applications experts.
A  qualified  marine  electronics  technician  should  install  your  Navigator  II, 
as incorrect installation could void your warranty.
Introduction
Your static Navigator II comes with these standard components: 
	 •	 Camera	head	
	 •	 25’	 system	cable	that	goes	 from	 the	camera	 head	to	the...

Before you drill holes:
	 •	 Once	you	have	 selected	 your	mounting	 location,	verif y	that	you	will	have	 access	 to	both	 sides	 of 
    the mounting hardware
    o While  FLIR  provides  wood  screws,  we  STRONGLY  recommend  using  the  machine  screws,   
      washers and lock nut. To do so will require you (and possibly an assistant) to have access to   
      both sides of the mounting hardware
	 •	 Note	 also	whether	 you	will	have	 to	remove	 any	interior	 trim	panels	 to	gain	 access	 to	the...

camera Mounting – stat Ic co NFIgUrat Io N 
Once you have confirmed that the selected mounting location will provide an unobstructed view and a 
properly  framed  image,  use  our  template,  or  the  one  from  PYI,  to  determine  where  you  will  drill  your 
mounting holes.
Step 1 Using the “Camera Mounting Template” supplied as a part 
of  the  Installation  Packet  (or  the  one  supplied  with  the  PYI  shim, 
should  you  need  to  use  one)  as  a  guide,  mark  the  locations  of  the 
holes...