Firestorm 45 Government Instruction Manual

 
 
FireStorm .45 Government 
 
PARTS LIST – INSTRUCTIONS FOR USE – MAINTENANCE 
 
 
 
 
SPECIFICATIONS
 
 
CALIBER: 45 ACP
OPERATION:
 Semi-Automatic
ACTION:
 Single Action
OVERALL LENGTH:
 8 1/2
HEIGHT:
 5 1/16
WIDTH:
 1 1/2
BARREL LENGTH:
 5 1/8
WEIGHT:
 36 oz
SIGHTS:
 3 Dot Combat
SAFETIES:
 Extended Manual & Grip Safeties
FINISH:
 New Upgraded Matte, Duo-tone
GRIPS:
 Anatomically Designed Rubber Grips
 
 
 
 
FABRINOR – P.O. Box 290- 01080 VITORIA (Spain) 
IMPORTANT 
When ordering list Code Number,...

 
 
PARTS LIST 
 
A 034 Magazine Catch lock 
A 054 Main spring cap pin 
B 720 Firing pin safety spring 
D 110 Extractor spring 
D 119 Hammer pin 
D 120 Hammer strut 
D 121 Hammer strut pin 
D 122 Sear 
D 123 Sear pin 
D 124 Disconnector 
D 125 Trigger  
D 127 Safety lock 
D 128 Sear spring 
D 129 Main spring housing 
D 130 Main spring cap 
D 131 Main spring 
D 138 Recoil spring guide 
D 139 Plug 
D 142 Firing pin spring 
D 143 Firing pin firing pin retainer 
D 146 Magazine catch 
D 152 Plunger Tube 
D...

IMPORTANT When ordering list Code Number, Part Name, Caliber, Model and Serial Number. 
 
DISASSEMBLY OF THE FIRESTORM .45 GOVERNMENT
 
 
The FIRESTORM pistol is quite easily taken apart. The parts mentioned in the following 
instructions refer to those described and illustrated in the schematic. 
 
1. Press the magazine catch (D 146) with your left thumb and take out the magazine (T 185). 
2.  Press the plug (D 139), the grooved face of which can be seen under the mouth of the 
barrel and, at the same...

OPERATION OF THE FIRESTORM .45 GOVERNMENT 
 
TO LOAD:  depress the magazine catch, which is located immediately behind the trigger.  This 
will unlock the magazine.  To fill the magazine, place the cartridges so that the bullet ends are 
positioned over the leading edge of the follower.  Fill the magazine to capacity.  Now take the 
loaded magazine and slide it back into the lodging frame.  When the magazine is pressed firmly 
into position, you should hear a distinct “click”, which indicates that it is...

SLIDE LOCK SAFETY:  The Slide Lock Safety is located on the left of the pistol just below 
the back of the slide.  With the hammer fully cocked and the Slide Lock Safety applied, the 
upper part of the Slide Lock Safety engages the slide lock notch to prevent rearward movement 
of the slide, while an internal cam surface engages the sear to prevent forward hammer 
movement when trigger is squeezed.  This safety device can be applied only when the slide is 
fully forward and the hammer is in the fully...

  Do not carry a gun with a cartridge in the chamber without the safety being on. (Double 
action revolvers and some double action pistols have automatic internal safety mechanisms 
rather than manual safeties.) 
 
MAINTENANCE
 
 
1. All moving parts should be coated lightly. 
2. After firing, it is advisable to clean the barrel and chamber.  Residue formation in the 
chamber may be able to cause misfire, due to the fact that the cartridge does not lodge in 
the chamber completely. 
3. It is not...

of firing is not quite right.  DO NOT CONTINUE SHOOTING!  STOP IMMEDIATELY 
AND UNLOAD THE GUN, and take it and the ammunition to a gunsmith. 
 
6. A loaded cartridge case that becomes jammed in a semi-automatic gun between the slide 
(or bolt) and the barrel may be removed as follows:  Keep the muzzle pointed in a safe 
direction.  First, remove the magazine, and then pull the slide or bolt back and hold it or 
lock it to the rear.  Remove the jammed case by shaking it out, or pick it out with your...

with cartridges:  this can cause dangerous malfunction.  Be sure your ammunition is the 
proper caliber for your gun:  you will find the proper caliber permanently engraved on the 
gun.  Do not use any other caliber ammunition. 
 
2. Reloading ammunition is a science, and improperly loaded ammunition can cause severe 
damage to your gun, and serious injury to both the shooter and other persons.  Use 
ammunition approved by the Sporting Arms and Ammunition Manufacturers’ Institute, 
Inc, of the United...

them excessively.  Lubricants, especially aerosol sprays, can penetrate cartridge primers 
and cause the ammunition to misfire.  Some lubricants can get inside the cartridge cases 
and prevent the powder from igniting.  If only the primer ignites, the bullet may become 
lodged in the barrel. 
 
 
 
GUN CARE 
 
1. When your gun is delivered, it is factory packaged and has a light coating of protective 
grease and oils.  Clear all packing grease and oil from the bore and exposed mechanism 
before loading....

Walker Arms Company 
499 Dallas Road #820 
Selma, Al. 36701  
Tel: 334-872-6231  
Reynersons 
10044 Hooper Rd. 
Baton Rouge, LA 70818 
Tel - 225-261-4860 
 
Ahlmans 
9525 W. 230th Street 
Morristown, Mn. 55052  
Tel: 507-685-4243 or 4244  
 
 
5. With your gun, enclose a letter stating the serial number, caliber, and barrel length of the 
gun, and what work is needed or what problem you experienced with it.  Be specific, do 
not merely say “defective” or “repair as needed.”  Also, enclose copies of any...