Faroudja Fdp-Dila3 Instructions

41
MENU
V- K EYSTONE H-KEYSTONE VOL.
EXIT
ENTER1~6
6
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
1~6
6
´ ´
´
´
´
´
´´
Image adj.
Set up
Logo
Options
Language
Information
AENTERENTER
(-) (+)12(-) (+)12
GBR
Capture menu     
Menu pos.     
Horiz.move     
Ve rt.move     
Horiz.size     
Ve rt.size     
Capture start     
Image adj.
Set up
Logo
Options
Language
Information
AENTER
(-) (+)12(-) (+)12
GBR
Capture menu     
Menu pos....

42
Handle
 When lamp time exceeds 1000 hours:
When the accumulated lamp time reaches 1000, a message
indicating “1000 hr“ will appear on the projected screen.
* Press any key to delete the message.
 When lamp time exceeds 1900 hours.
•When the accumulated lamp time reaches 1900 hours:
The LAMP indicator on the projector lights up.
• When the accumulated lamp time exceeds 1900 hours:
“Lamp replacement” appears on the screen.
* Press any button to delete the message.
Replacing the Lamp
The light source...

43
Lamp unit
3. Remove the lamp unit.
Replacing the Lamp
4. Insert the new lamp unit fully in.
5. Close the handle, and tighten the screw.
Tighten the two screws with a ª screwdriver.
6. Attach the light-source lamp cover and tighten
the screw.
Tighten the two screws with a ª screwdriver.
Note
When closing the lamp cover, please insert the left
side (with the two claws) in first and then ensure that
the protruding part found on the reverse side of the
cover fits snugly into the hole of the main unit. As...

44
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
PRESET HIDE EXIT
press for 
2 seconds
EXIT
PRESET HIDE
V
OL(   )
Press as per normal
Press for 2 seconds or more
Replacing the Lamp
1. Insert the main plug. The projector will go into the stand by  mode.
ON: STAND BY indicator lights up.
2. Press the EXIT, HIDE, PRESET buttons on the remote
control sequentially, then press VOL 
ª  f or 2 seconds or
more.
The STAND BY and OPERATE...

45
lower filterinner filter
claw
lower filter
inner filter
claw
● Put on rubber gloves when using a neutral detergent.
● After you washed the filter in water, make sure that the
filter is completely dry before reinstalling, otherwise elec-
tric shock or malfunction could occur.
● Do not clean this filter using a vacuum cleaner. Since the
filter is soft, it may be sucked into the vacuum cleaner or
be damaged by it.
Cleaning and Replacing the Filter
Clean the filter regularly or it may not work...

Troubleshooting
Before consulting your authorized dealer, please check the following points.
Symptom Probable cause Corrective action Page
Power is not sup-
plied.
Light is not emitted,
or light is dim.
With power on, the
projector works but
stops abruptly in a
few minutes.
Video image does
not appear, or audio
sound does not oc-
cur. Is the power cord disconnected?
Is the light-source lamp cover closed correctly?
Is the filter inserted correctly?
Has the lamp life expired? (Has the lamp time
reached...

Troubleshooting
Symptom Probable cause Corrective action Page
Video image is
fuzzy.
Video image is ab-
normally dark or
bright.
Color is poor or un-
stable.
The upper part of
the  video image
bows or distorts.
Remote control unit
does not work. Is focus adjusted correctly?
Is the projector placed too near or too far from
the screen?
Are “Tracking” and “Phase” adjusted correctly?
Is “Brightness” adjusted correctly?
Is picture quality (color, density, etc.) adjusted
correctly?
Is the correct “Decoder”...

48
PC 1
No Input
PC 1
Frequency of input signal is out of range.
No device is connected to the input terminal.
The terminal is connected but no signal is output from the connected device.
•The selected input mode (input terminal) name is shown above the mes-
sage.
[Please input the image signal.
The frequency of the input video signal is out of range.
[Please input the video signals of which frequency is within the projecto\
r’s
specifications.
What to do when these messages are displayed
Message Cause...

49
1000h
EXIT
Lamp replacement
EXIT
Lamp replacement
EXIT
WARNING
What to do when these messages are displayed
When the “Lamp time” reaches 1000 hours
[ A message indicating “1000 h” appears on the projected screen.
• Press any key to delete the message.
Every time the projector is turned on, this message appears on the screen
when the accumulated lamp time reaches between 1900 hours to 2000 hours.
[  Press any button to delete the message.
     Get ready a new light-source lamp or replace the...

 About warning indicators
If something abnormal has occurred in the projector, the warning mode sets on and the abnormality will be indicated by a combin a-
tion of indicators displayed on the control panel as shown in the following table.
Then, the projector automatically stops projection and runs the cooling \
fan for about 90 seconds.
Wa rning Indication

  Action to be taken upon warning indications
Please follow the procedures below.
For No.1-3
No.1 : Unplug from the main power outlet and restart...