Farberware 15Bar PumpDriven Espresso Machine FES15B User Manual

							PREPARING CAPPUCCINO
In Italy, cappuccino is usually 1 part espresso to 2 parts milk plus
froth. Americans love to add cinnamon, sugar, shaved chocolate,
nutmeg and/or various liquors to taste.
NOTE: When preparing 1 or 2 cups of cappuccino, it is recommended
that you place the cups of finished espresso on top of the Warming
Plate with a cloth or saucer covering the cups. This will help to
keep the espresso hot.
NOTE: The best frothed milk is obtained when
fresh, cold skim milk is used. When frothing
milk, the volume of the milk will double.
NOTE: When preparing cappuccino, use a
cappuccino cup with a capacity of at least 
5 ounces. Fill the cup half-full with espresso.
1. Make sure the Steam Outer Tube is properly
attached and locked onto the Steam Inner
Tube before beginning to froth the milk.
2. Before steaming, make sure the Steam
Release Knob is in the OFF (-) position.
3. Fill a stainless steel frothing pitcher 1/3 to 
1/2 full with fresh, cold milk and set aside. 
4. Preheat according to PREHEATING THE
ESPRESSO MAKER section of these Use &
Care Instructions.
5. The       / OK Brew Light will be illuminated to signal the Espresso
Maker is ready to froth milk. Turn the Selector Dial to  /Steam.
The Steam Light will illuminate.
REMINDER: Before frothing, make sure the tip of the Steam Nozzle 
is just under the surface of the milk. Otherwise, splattering 
may occur.
6. Hold the pitcher by the handle and bring up to
the Steam Nozzle. Insert the tip of the Nozzle
just under the surface of the milk. Turn the
Steam Release Knob gradually counter-
clockwise; from the minimum steam (-) to the
maximum steam (+)  position (see Figure 8),
moving the pitcher in a slightly circular motion
to froth the milk. 
7. After frothing, turn the Steam Release Knob
clockwise to the minimum (-) position. WAIT
UNTIL NO FURTHER STEAM EMERGES FROM
THE STEAM NOZZLE. This will allow any extra
steam to be released. After all of the steam is
safely released, turn the Selector Dial to 
“O” OFF.
STEAM NOZZLE
Steam 
Inner Tube
(P/N 31406)
Steam 
Outer Tube
(P/N 31405)
10
Figure 7
Steam
Nozzle
Minimum Steam (-)
Maximum Steam (+)
Figure 8
SAFETY WARNINGS
•Proper precautions must be made to avoid burns from sprays of hot
water or steam.
•Avoid touching any hot surfaces on the machine or any parts of the
Filter Basket Holder, Filter Baskets, or any parts of the Steam Nozzle
while the Espresso Maker is in use or after it is just been used to
prepare hot beverages.
•To avoid water spillage, it is necessary to empty the Removable Drip
Tray when the Red Water Level Float rises and becomes visible. To
remove the Drip Tray, no cups must remain on the Drip Plate. Lift
the Drip Plate and Drip Tray up and off the unit. Empty water, rinse,
and replace.
BEFORE USING FOR THE FIRST TIME
Before brewing your first cup of
espresso coffee, we suggest you
pre-clean the machine. Place the
Espresso Maker on a level surface,
situated within close proximity to a
sink to discard water.
1. Make sure the Espresso Maker
is unplugged and the Selector 
Dial is in the “O” OFF position.
Remove the Lid. Use the Water
Reservoir’s back handle to lift it
up and off the unit.
2. Fill the Water Reservoir to the
MAX mark. Replace Water
Reservoir in its original position
on the back of the unit by sliding
the Reservoir’s locking clips
down behind the Reservoir
Locking Tab (see Figure 3), and
connecting the Valve at the
bottom of the Water Reservoir
with the hole in the Base of the
unit. Make sure it fits securely
into place. Replace the Lid.
NOTE: Never fill the Water Reservoir past the MAX mark. Never operate
the appliance without water in the Reservoir. Always refill the Water
Reservoir when the water level falls below the MIN mark.
3. Place an empty (do not add coffee) 2-Cup Filter Basket into the Filter
Basket Holder. Insert and lock into the Espresso Maker following the
detailed description in the section: INSERTING/REMOVING THE
FILTER BASKET HOLDER. 
5
Figure 3
Reservoir
Locking Clips
Reservoir
Locking 
Tab
Water 
Hole
Base Water Reservoir 
Water 
Valve 
(not shown)
Lid
FBW_FES15B_IB_25-5-06  5/25/06  4:18 PM  Page 11 
						

							8. The froth will not readily pour from the container, since it
separates from the heated milk. The top half will be frothed, the
bottom half will be milk. Pour in an equal amount of warm milk
into the cup of espresso. Spoon the frothed milk onto the top.
9. Remove the Filter Basket Holder from the
Espresso Maker; grasp the Filter Basket
Holder Handle firmly and turn clockwise
until the Handle faces the left UNLOCKED
position. The Filter Basket Holder will drop
down and out of the unit. Empty the Filter
Basket; flip the Basket Holder Clip up and
over the rim of the Filter Basket to hold it in
place with your thumb; knock out the used
coffee (see Figure 9). Place used E.S.E. pod 
into a waste receptacle.
CAUTION: The Filter Basket and Filter Basket Holder are hot after
brewing. Allow to cool thoroughly before touching.
10. Unplug the Espresso Maker after each use.
11
PREPARING CAPPUCCINO   (Continued)
Figure 9
4 1. Control Panel
2. Top Warming Plate  (P/N 31402)
3. Lid for Water Reservoir  (P/N 31403)
4. Water Reservoir  (P/N 31404)
5. Steam Release Knob
6. Steam Nozzle  (P/N 31405)
7. Drip Plate  (P/N 31407)
8. Removable Drip Tray with 
red Water Level Float  (P/N 31408)
9. Steam /Steam Light
10. “O” OFF11. Heater Mode /Heater Light
12. / OK Brew Light
13. Selector Dial
14. Tamper  (P/N 31413)
15. Filter Handle Clip
16. Filter Basket Holder (P/N 31409)
17. Pressure Reducer Lever
18. 1-Cup Filter Basket  (P/N 31410)
19. 1-Cup Basket Spacer  (P/N 31411)
20. 2-Cup Filter Basket  (P/N 31412)
GETTING TO KNOW YOURFARBERWARE®
ESPRESSO MAKER
PRODUCT MAY VARY SLIGHTLY FROM ILLUSTRATIONS
Figure 2
Selector Dial
1. 2. 3.
4.
5.
6.9. 10. 11.
12.
13.
16.
17.18.
19.
20.14.
15.
7. 8.
Figure 1
FBW_FES15B_IB_25-5-06  5/25/06  4:18 PM  Page 9 
						

							USER MAINTENANCE INSTRUCTIONS
This appliance requires little maintenance. It contains no user 
serviceable parts. Do not try to repair it yourself. Any servicing
requiring disassembly must be performed by a qualified appliance
repair technician.
1. Unplug the Espresso Maker from the electrical outlet and allow to
cool completely before cleaning.
2. The Filter Basket Holder and Filter Basket(s) should be emptied 
and rinsed thoroughly with warm water after every use. 
If necessary, clean the Filter Basket(s) with a kitchen brush. A pin
may be used to clear any clogged holes. Dry thoroughly.
3. The Steam Nozzle separates for easy cleaning. (See Figure 7.)
Disassemble the Steam Nozzle by holding the 2 fins of the Steam
Nozzle in one hand and turning the Outer Tube counter-clockwise
and pulling it down to remove. Do the same for the Steam Inner
Tube. These can be rinsed or soaked in hot water to clean. If
necessary, use a pin to clear any blockage. Replace by turning
clockwise and fit into position.
4. To remove the Drip Tray, no cups must remain on the Drip Plate.
Remove the Filter Basket Holder from the machine. Remove the
Drip Plate and then the Drip Tray. Empty water, rinse, and replace.
5. Wipe the outside of your Espresso Maker with a damp cloth. Never
use solvents or any detergents that may scratch or damage the
surface of the machine.
6.NEVER IMMERSE THE ESPRESSO MAKER IN WATER OR ANY
OTHER LIQUID.
12
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to
fit into a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to modify the plug in any way.
SHORT CORD INSTRUCTIONS
A short power-supply cord is provided to reduce the risk resulting
from becoming entangled in or tripping over a longer cord.
Do not use an extension cord with this product.
PLASTICIZER WARNING
CAUTION: To prevent Plasticizers from migrating from the 
finish of the counter top or table top or other furniture, place 
NON-PLASTICcoasters or place mats between the appliance 
and the finish of the counter top or table top.
Failure to do so may cause the finish to darken. Permanent
blemishes may occur or stains can appear.
ELECTRIC POWER
If the electrical circuit is overloaded with other appliances, your
appliance may not operate properly. It should be operated on a
separate electrical circuit from other appliances.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
REMOVE THE BOTTOM COVER. NO USER-SERVICEABLE PARTS
INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE
PERSONNEL ONLY.
3
FBW_FES15B_IB_25-5-06  5/25/06  4:17 PM  Page 7 
						

							13
DESCALING
If you live in a hard-water area, minerals and calcium found in the
water will accumulate and affect the operation of your machine. After
approximately every 300 cups of coffee, your Espresso Maker should
be cleaned with distilled vinegar in the following manner in order to
remove the mineral deposits.
1. Before cleaning your Espresso Maker, make sure the Steam Release
Knob is in the minimum (-) position (see Figure 8) and the
appliance is thoroughly cooled and has been disconnected 
from the wall outlet.
2. Add 2 tablespoons of distilled vinegar to 1 liter of water. Add
vinegar solution to the Water Reservoir. 
3. DO NOT attach the Filter Basket Holder to the Espresso Maker.
Place a container on the Drip Tray under the Coffee Spout(s).
4. Turn the Selector Dial to the Heater  position. The Heater Light
will illuminate. The      / OK Brew Light will illuminate when the
Heater is ready.
5. Turn the Selector Dial to the Brew  / OK position and allow half
of the solution in the Water Reservoir to flow out. Then STOP the
flow by turning the Selector Dial to “O” OFF.
6. Allow the vinegar solution to sit for about 15 minutes, then
continue to brew the solution until the Water Reservoir empties.
7. To eliminate the remains of the solution and the calcium, rinse the
Water Reservoir well, fill with clean water and replace.
8. Turn the Selector Dial to the Brew  / OK position and allow all
of the remaining solution in the Water Reservoir to flow out.
9. Turn the Selector Dial to the Heater  position and repeat steps
7 and 8 one more time.
ADDITIONAL IMPORTANT SAFEGUARDS
WARNING: This appliance generates heat and escaping steam during
use. Proper precautions must be taken to prevent the risk of
burns, fires, or other injury to persons or damage to property.
1. All users of this appliance must read and understand these Use &
Care Instructions before operating or cleaning this appliance.
2. The cord to this appliance should be plugged into a 120V AC
electrical outlet only.
3. Use water only in this appliance! Do not put any other liquids or
food products in this appliance. Do not mix or add anything to the
water placed in this appliance, except as instructed in the User
Maintenance Instructions to clean the appliance.
4. DO NOT attempt to move an appliance containing hot liquids.
Allow appliance to cool completely before moving.
5. Keep appliance at least 4 inches away from walls or other objects
during operation. Do not place any objects on top of appliance
while it is operating. Place the appliance on a surface that is
resistant to heat.
6. If this appliance begins to malfunction during use, turn the Selector
Dial to “O” OFF, then immediately unplug the cord. Do not use or
attempt to repair the malfunctioning appliance.
7. If this appliance falls or accidentally becomes immersed in water
or any other liquid, unplug it immediately. Do not reach into the
water! Do not use this appliance after it has fallen into or has
become immersed in water. Contact Consumer Service for
examination and repair.
8. Do not leave this appliance unattended during use.
9. Always use fresh, cool water in your appliance. Warm water or
other liquids, except as listed in the DESCALING section, may
cause damage to the appliance.
10. Keep Steam Release Knob in closed position when not in use.
CAUTION: Relieve pressure through the Steam Nozzle or Pressure
Reducer Lever before removing Filter Basket Holder.
2
FBW_FES15B_IB_25-5-06  5/25/06  4:17 PM  Page 5 
						

							USE & CARE INSTRUCTIONS
ESPRESSO MAKER
FES15B
LIMITED ONE-YEAR WARRANTY
Warranty Coverage: This product is warranted to be free from defects in
materials or workmanship for a period of one (1) year from the original purchase
date. This product warranty is extended only to the original consumer purchaser
of the product and is not transferable. For a period of one (1) year from the date
of original purchase of the product, our Repair Center will, at its option, either 
(1) repair the product or (2) replace the product with a reconditioned comparable
model. These remedies are the purchasers exclusive remedies under 
this warranty.
Warranty Service: To obtain warranty service, you must call our warranty
service number at 1-800-233-9054 for return instructions on how to deliver the
product, in either the original packaging or packaging affording an equal degree
of protection to the Repair Center specified below. You must enclose a copy of
your sales receipt or other proof of purchase to demonstrate eligibility for
warranty coverage.
To returnthe appliance, ship to:To contact us,please write to, call, or email:
ATTN:  Repair Center Consumer Relations Department
708 South Missouri Street PO Box 7366
Macon, MO  63552  USA Columbia MO  65205-7366 USA
1-800-233-9054
E-mail:[email protected]
What Is Not Covered: This warranty does not cover damage resulting from
misuse, accident, commercial use, improper service or any other damage caused
by anything other than defects in material or workmanship during ordinary
consumer use. This warranty is invalid if the serial number has been altered or
removed from the product. This warranty is valid only in the United States and
Canada.
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND
CONDITIONS, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES AND
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE OR USE ON THIS PRODUCT ARE LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may have other rights under the laws of
your jurisdiction.
FARBERWARE ® and Millennium® are registered trademarks of Farberware Inc.®
Manufactured and sold pursuant to a license from Farberware Inc.®
For more information on our products, visit our website:  
www.maxim-toastmaster.com.
©2006 All rights reserved. P/N 61869
Made in China 5/06
FBW_FES15B_IB_25-5-06  5/25/06  4:17 PM  Page 1