European American Armory Over And Under Double Rifle Izh94 Express Instructions Manual

							11 and the forend is locked into the receiver and
barrel.
• 6) Fig 5: Make sure the trigger block safety
is engaged after completion of assembly.
(Red dot covered)
To Load Double Rifle:
• 1) Fig 7: Make sure the Double Rifle is
pointed in a safe direction at all times, the
trigger block safety is engaged, and never
allow fingers or objects to contact trigger.
Warning ***
Do not load double rifle
until you are ready to fire
• 2) Do not disengage the safety until you are ready to fire.
• 3) Make sure the ammo that you are using is the correct caliber. The top barrel
is marked with the caliber of the rifle cartridge.
• 4) Fig 8: Visually inspect the chambers and barrel for obstructions by
breaking open the Double Rifle by pushing the top lever to the side and tipping
the barrel down. The chamber and barrel should be free of oil or grease or
obstructions.
• 5) After inspection load the correct type of cartridge into the barrel. Make sure
that the cartridges are flush with the extractor, then close the action by swinging
the barrel up until it locks into the receiver and the top lever moves to the center
position. If the top lever does not move to the center break open the action again
and check to see if the cartridges are fully seated in the chamber. If the
cartridges are fully seated then re-close the action. If the cartridges are not fully
seated check the chamber for blockage and check the cartridges for
deformation and retry closing the action once more. If the cartridges are the
correct type and the chamber is not blocked and the cartridges are not
deformed and the top lever does not move at least three quarters of the full travel
distance to the center after closing then unload the gun (follow unloading
instructions) and have a competent gunsmith look at the gun or return the gun
back to E.A.A. Corp. for review. Note: The top lever may not move completely
to the center on a new Double Rifle until the gun is broken in. The lever must
move at least three quarters of the full travel distance. Try to move top lever to
center by hand do not force.Fig. 8 
						

							12 WARNING
Once you have broken open the Double Rifle action with the forearm installed
the internal hammers are cocked and under spring tension. We suggest that
you do not keep, carry or store the gun with the hammer springs under
compression. Follow unloading instructions and with the gun unloaded or the
barrel removed pull the triggers to release the hammer springs from their
compressed state.
There is no excuse for not being careful.....
W A R N I N G
Never load a cartridge into the chamber until
you are ready to fire the Double Rifle...
To Fire Double Rifle:
W A R N I N G
• Do not disengage the trigger block safety until the Double Rifle is pointed in
a safe direction and you are ready to fire.
• If a cartridge does not fire and the trigger has been pulled and the trigger block
safety is disengaged...Stop! and do the following: a) Make sure the gun is
pointed in a safe direction b) Engage the trigger block safety c) Wait 60 seconds
d) Follow the instruction below for unloading the Double Rifle.
• If during firing the sound of any cartridge is noticeably softer or louder than the
previous cartridge fired, Stop! Do not load another cartridge or fire another
cartridge and do the following:  a)  Make sure the gun is pointed in a safe
direction b) Engage the trigger block safety c) Follow the instruction below for
unloading the Double Rifle d) With the Double Rifle unloaded visually inspect
the Double Rifle for barrel blockage or damage and inspect the mechanical
portion and receiver of the Double Rifle for damage before continuing.
PLEASE READ AND UNDERSTAND  ALL WARNINGS IN
THIS MANUAL BEFORE FIRING DOUBLE RIFLE, MAKE
SURE YOU KNOW WHAT YOU ARE SHOOTING AT
There is no excuse for not being careful.....
• 1) Make sure the gun is pointed in a safe direction and that you are
wearing ear and eye protection and keep fingers away from triggers.
• 2) Engage trigger block safety if not already engaged
• 4) Disengage the safety and begin firing only when you are ready to fire
and the Double Rifle is pointed in a safe direction to be fired. At this point the
Double Rifle will fire if the trigger is pulled.
To Unload Double Rifle:
• 1) Make sure the gun is pointed in safe direction and the trigger block
safety is engaged 
						

							13 There is no excuse for not being careful.....
• 2) After completing step one completely... push the top lever to the right till
the action breaks open.
• 3) Then fully open the action and remove the cartridges.
• 4) Visually check that the barrels are free of obstructions and then close
the Double Rifle action.
• 5) We suggest that you remove the hammers spring compression by
pulling each trigger or in the case of a single trigger gun pulling the trigger
for each barrel.
• 6) Make sure the trigger block safety is engaged  after the Double Rifle
action is closed
To Disassemble The Double Rifle:
• 1) Make sure the Double Rifle is unloaded (FOLLOW UNLOADING
INSTRUCTIONS) and pointed in a safe direction.
• 2) Make sure the trigger block safety is engaged.
There is no excuse for not being careful.....
• 3) Remove the forend from the barrel by pulling out the lever in the lower
center of the forend and removing the forend in a downward out ward swing
motion. Never force the forend off the barrel and receiver.
• 4) With the barrel and receiver supported with one hand push the top lever
to the right fully and tip the barrel down until it disengages from the receiver.
Check the barrel for damage and blockage after removal
MANUFACTURER’S WARNING
This firearm was manufactured to properly perform with the original parts as
designed.  It is your duty to make sure any parts you buy are correctly installed
and that neither replacements nor originals are altered or changed.  Your gun
is a complex tool with many parts that must relate correctly to other parts for
safe and accurate operation.  Putting a gun together wrong or with modified
parts can result in a damaged gun, injury or death to you or others through
malfunction.   Always let a qualified gunsmith work on your gun or at least,
check any work not performed by a gunsmith.  Firearms safety is your primary
concern. THE GUN OWNER MUST ACCEPT FULL RESPONSIBILITY FOR
THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM
AFTER ANY DISASSEMBLY OR REPLACEMENT OF PARTS.
Cleaning And Maintenance Of Double Rifle:
A)  Follow procedures for unloading Double Rifle as described previously
B)  Follow procedures for disassembly of Double Rifle as described previously 
						

							14 C)  Materials needed to clean this Double Rifle are: a cleaning rod, cotton bore
patches, brass bore brush, powder solvent, a small soft brush and good quality
gun oil.
WARNING: Lead or lead compounds are known to the State of California to
cause cancer, birth defects, reproductive toxicity, and other serious physical
injury.  Those who clean firearms should take protective measures to avoid
contact or exposure to such chemicals.
There is no excuse for not being careful.....
D)  Using the bore brush with powder solvent scrub the barrel and chamber to
remove any powder and lead residue in the bore.  Always and lastly, swab with
cotton patch with gun oil to coat and protect the bore and chambers from rust
and corrosion.
E)  Any powder fowling on the firing wall, barrel, etc. can be easily cleaned with
a brush and powder solvent.
F)  All external surfaces should be wiped down with a light coat of rust
preventative.  Avoid using too much oil as dust and/or debris can get trapped
in the oil creating a gum that in time will cause misfires.
G)  CAUTION in using solvents in gun bore cleaning.  Prolonged or excess
contact with finish or bluing can damage the gun’s finish.  Be sure to wipe away
all excess solvent and then lubricate with oil.
H)  A gun should be cleaned after firing.  In addition, external parts should be
wiped with an oiled cloth after handling.  A light oil is ordinarily all that is
necessary in cleaning if the gun has not been fired or fired very little.  If a gun
is used frequently, it must be cleaned after each firing and regularly serviced by
a professional gunsmith.  If the gun has been stored, remove all excess oil and/
or grease before firing.  Always check to be sure that no cleaning patch or other
obstruction remains in the bore or chambers before firing.
DANGER – AMMUNITION WARNING
Firearms may be damaged and serious injury or death to the shooter or
bystander may result from any condition which contributes to the generation of
excessive pressure or uncontrolled release of gas within the firearm.  Such
adverse conditions can be caused by bore or chamber obstruction, propellant
powder overloads or by defective, incorrect or improperly loaded and
assembled cartridge components.  Even the strongest firearm can be blown up
as a result of excessive pressure.  It is extremely dangerous to use a cartridge
whose pressure is greater than that developed by cartridges loaded to industry
standards.
AMMUNITION (CARTRIDGES) NOTICE
We specifically disclaim responsibility for any damage, injury or death
occurring in connection with or as the result of the use of European American
Armory Double Rifle of faulty, non-standard, remanufactured, hand loaded or
reloaded ammunition, used cartridges or cartridges other than factory 
						

							15 cartridges for which the firearm was originally chambered.
LUBRICATION WARNING
Firing a Double Rifle with oil, grease or any other material even partially
obstructing the bore may result in damage to the Double Rifle and injury to the
shooter and those nearby.  Do not spray or apply lubricants directly on
ammunition.  If the powder charge of a cartridge is affected by the lubricant, it
may not be ignited, but the energy from the primer may be sufficient to push the
bullet into the bore where it may become lodged.  Firing a subsequent bullet into
the obstructed bore will damage the Double Rifle and may cause injury to the
shooter and those nearby.  Use lubricants properly.  You are responsible for the
proper care and maintenance of your firearm and ammunition.
ONE YEAR LIMITED WARRANTY
This European American Armory Corp. firearms is warranted to the original
retail customer for One Year from date of purchase against defects in material
and workmanship.  All parts and labor or replacement at our option are
covered. Wood Stock and Wood Forend are not covered by the One Year
Warranty. The warranty on the wood stock and forend is 60 days from purchase
and only covers manufactured and material defects.
Transportation to and from our repair facilities, government fees,  damage
caused by failure to perform normal maintenance, sales outside the United
States, damage due to use of high velocity, high pressure, reloaded or other
nonstandard ammunition, or any unauthorized repair, modification, misuse,
abuse,  or alteration of the product is not covered by this Limited Warranty.
Any implied warranties, including the implied warranties of merchantability
and fitness for a particular purpose, are limited to one year from date of original
retail purchase.  Consequential or incidental damages and/or expenses, or any
other expenses are not covered by this warranty.
To obtain warranty performance send your firearm with proof of retail
purchase, freight prepaid to:
European American Armory Corp.
3855 North U.S. Highway One
Cocoa, Florida 32926
W A R N I N G
Altering or modifying parts and/or internal safeties is dangerous and will void
the warranty.  This Double Rifle was manufactured to perform properly with the
original parts as designed.  It is your duty to make sure any parts you buy are
made for this firearm and are installed correctly and that neither the
replacements nor originals are altered or changed.  Your gun is a complex
precision tool with many parts that must relate correctly to other parts in order
for proper and safe operation.  Putting a gun together wrong or with incorrect or
modified parts can result in a damaged gun, danger, and injury or death to you
and others through malfunction.  Always have a qualified gunsmith work on 
						

							16 your gun or at least check any work not performed by a gunsmith.
YOUR OWNERS’ MANUAL
Always keep this manual with your firearm.  Make sure you understand all the
warnings, operation instructions and safety procedures.  When you lend, give
or sell the firearm, be sure this manual goes with it.  You can get a copy of this
manual from European American Armory on request.
ALL PARTS ORDERS ARE SUBJECT TO A $10.00 CHARGE FOR SHIPPING
AND HANDLING.  Please state Model, Caliber, Serial Number, and Finish Color
when ordering.  For parts, information and service contact: European
American Armory Corp., 3855 North U.S. Highway One, Cocoa, Florida 32926
Phone: (321) 639-4842.1.Adjusting screw
2.Washer
3.Rear sight screw
4.Rear sight
5.Spring
6.Plunger
7.Adjusting nut
8.Sling swivel base
9.Rear sight base
10.Bottom barrel
11.Top barrelFig. 2 - Barrel adjusting mechanism
of IZH94 “Express” Double Rifle
Adjustment:
Turn jack screw clockwise to
make point of impact tighter.
Turn jack screw counter
clockwise to increase distance
between points of impact. 
						

							17 PARTS LIST
Fig. 1 - IZH94 “Express” Exploded View1.Barrel
2.Extractor
3.Extractor screw
4.Front sight
5.Sling swivel ring
6.Sling swivel pivot
7.Hinge
8.Forend
9.Forend screw
10.Forend screw rim
11.Forend latch base
12.Forend latch
13.Forend latch pivot
14.Forend latch spring
15.Receiver
16.Top lever
17.Top lever screw
18.Locking bar rocker
19.Locking bar
20.Spring
21.Top firing pin
22.Bottom firing pin
23.Firing pin spring
24.Right hammer
25.Left hammer
26.Hammer pivot
27.Mainspring guide
28.Mainspring29.Right sear
30.Left sear
31.Sear pivot
32.Sear spring
33.Right cocking bar
34.Left cocking bar
35.Safety slide
36.Safety base
37.Safety
38.Safety pivot
39.Safety spring
40.Spring
41.Connecting-link
42.Pin
43.Safety-on bar
44.Interceptor
46.Spring
47.Screw
48.Bridge
49.Trigger base
50.Screw
51.Locking bar catch
52.Locking bar catch spring
53.Locking bar catch pivot
54.Right trigger
55.Left trigger
56.Trigger pivot
57.Trigger bar58.Cocking cam
59.Cocking cam pivot
60.Trigger guard
61.Woodscrew
62.Buttstock
63.Buttstock screw
64.Washer
66.Buttplate
67.Woodscrew
68.Woodscrew
69.Rear sling swivel base
70.Hinge screw
71.Forend latch screw
72.Washer
77.Rear sight
78.Rear sight screw
79.Washer
80.Front sight plunger
81.Front sight spring
82.
83.Front barrel bushing
84.Pin
85.Extractor retaining pin
86.Extractor pin spring
87.Extractor pin
88.Hinge shoulder
89.Pin 
						

							18      WARNING
Children are attracted to and can operate firearms that
can casue severe injuries or death.
Prevent child access by always keeping guns locked
away and unloaded when not in use.  If you keep a
loaded firearm where a child obtains and improperly
uses it, you may be fined or sent to prison.
     ADVERTENCIA
A los ninos los atroen las armaside de fuego y los
pueden hacer funcionar.  Ellos pueden causarses
lesiones graves y la muerte.
Evite que los ninos tengon acceso a los armas de fuego
guardandolas siempre con llave y descargadas cuando
no las este utilizando.  Si usted tiene un arma de fuego
cargado en un lugar en que un nono tiene acceso a
ella y la usa indebidamente. le pueden dar una
multa a enviarlo a la carcel.!!