Epson Stylus Pro 10600 User Manual

2-14
2-14|Using Paper and Other Media
5. Pull the paper set lever out to the released position. The Paper Out light 
on the control panel comes on and 
LOAD PAPER appears on the 
control panel display.
6. Feed the paper into the paper slot. You hear the paper suction fans 
come on. 
7. If you’re loading heavy paper, you may need to increase the suction 
strength by pressing the 
Paper Feed + button. This helps hold the 
paper in place during loading and printing.
For lightweight paper, decrease the...

2-15
Using Paper and Other Media|2-15
8. Pull the paper down so it extends all the way through the slot.
9. Turn the roll back to remove any slack. Then align the paper with the 
two rows of holes at the paper exit.
 

2-16
2-16|Using Paper and Other Media
10. Push the paper set lever all the way in, then close the roll paper cover. 
PRESS PAUSE BUTTON appears briefly on the control panel display.
11. Press the 
Pause button. The print head moves and the paper feeds into 
printing position automatically. 
READY appears on the control panel 
display. (Even if you don’t press 
Pause, the paper and printer move into 
printing position automatically after 10 seconds.)
Caution
To avoid damaging the 
printer, never move the...

2-17
Using Paper and Other Media|2-17
Selecting Print Settings for Roll Paper
Before printing, you need to make sure you select the correct settings in your 
printer software. If you’re using the EPSON printer driver, check the 
following:
Always choose an appropriate Media Type setting in your printer 
software before you send your job. See page 2-7 for instructions. If 
you’re printing on non-EPSON paper, or on a paper type not supported 
by the driver, you may need to use the Paper Configuration menu...

2-18
2-18|Using Paper and Other Media
Removing Unused Roll Paper
Once your printouts are removed from the printer, follow these steps to 
remove any unused paper:
1. Pull the paper set lever out to the released position. 
2. Wind the remaining paper back onto the roll.
3. Secure the paper with a roll paper belt. The shorter belt is for 2-inch roll 
paper; the longer one is for 3-inch rolls. 
Caution
To avoid damaging the 
printer, never move the 
paper set lever while the 
Operate or Pause light 
is...

2-19
Using Paper and Other Media|2-19
4. Remove the roll paper and spindle from the printer. 
5. To remove the paper from the spindle, lay it on a flat surface, then 
loosen the removable paper stop by tapping it with your hand. Slide the 
paper stop off the end of the spindle, then remove the paper.
Always store unused roll paper in its original package—including the bag, 
end caps, and box.
Using Cut Sheet Paper
You can print on many types of cut sheet paper and other media. The 
printer accepts sheets...

2-20
2-20|Using Paper and Other Media
4. Feed the sheet into the paper slot until it meets resistance. Make sure the 
right edge of the paper is straight and aligned with the scale on the roll 
paper cover.
 You see PRESS PAUSE BUTTON on the control panel 
display.
5. Press the 
Pause button. The print head moves and the sheet feeds into 
printing position automatically. 
READY appears on the control panel 
display. 
6. Print your page. After it is finished, the sheet stays in the printer.
7. To remove...

2-21
Using Paper and Other Media|2-21
4. Pull the paper set lever out, to the released position. Then open the 
lower cover. (The cover has tabs that support the posterboard.) 
5. Feed the posterboard into the paper slot until it meets resistance. 
6. Align the board with the scale on the roll paper cover.
Note
If you’re using stock 
more than 39 inches 
long, load it long edge 
first (in landscape 
orientation).
 

2-22
2-22|Using Paper and Other Media
7. Push the paper set lever all the way in, then close the lower cover. 
PRESS PAUSE BUTTON appears on the control panel display.
8. Press the 
Pause button. The print head moves and the board feeds into 
printing position automatically. 
READY appears on the control panel. 
(Even if you don’t press 
Pause, the board and printer will move into 
printing position automatically after 10 seconds.)
9. Run your print job. After it is finished, the posterboard stays in the...

2-23
Using Paper and Other Media|2-23
Using the Paper Basket
The paper basket is a cloth sheet that attaches to your printer and catches 
your printouts as they come out. This keeps the printouts from getting dirty 
or wrinkled. You can set up the basket either to catch the paper under the 
printer or to let it feed straight out in front. 
Catching Printouts in Front of the Printer
Follow these steps to set up the basket in front of the printer:
1. Unhook the basket rings from the metal rods, if they’re...