Epson Projector Pro G7100 User Manual

							

51
5.
Hold thelens firmly andslide thelock lever tothe Lock position (asshown) untilitlocks.
 6.
Replace thelens cover.
 7.
Ifprompted, selectYestocalibrate thelens.
 Note:
Lenscalibration helpstheprojector tocorrectly acquirethelens position andadjustment
 range,
andcantake upto100 seconds tocomplete. Whencalibration isfinished, thelens returns to
 the
same position itwas inbefore calibration. (ELPX01returnstothe standard position.)
 8.
When usingoneofthe following lenses,selectthelens type inthe Extended menu:ELPLS04,
 ELPLU02,
ELPLR04,ELPLW04, ELPLM06,ELPLM07,orELPLL07.
 Parent
topic:Attaching andRemoving aLens
 Removing
aLens
 You
canremove alens toreplace itwith adifferent lens.   
						

							

52
Caution:
Removethelens onlywhen necessary andmake surethefront ofthe projector isnot facing up
 when
youremove thelens. Thisprevents dirtordust from entering theprojector andlowering the
 projection
quality.Avoidtouching thelens withyour bare hands toprevent fingerprints onordamage to
 the
lens surface.
 1.
Center thelens using theLens Shift(remote) orLens (control panel)button.
 2.
Turn offthe projector andunplug thepower cord.
 3.
Pull thelens cover offofthe projector.
 4.
Hold thelens firmly asyou slide thelock lever tothe Release position(asshown) untilyouhear it
 click.

5.
Gently pullthelens straight outofthe projector.
 Parent
topic:Attaching andRemoving aLens   
						

							

53
Attaching
andRemoving theCable Cover
 You
canattach thecable cover thatcame withyour projector tohide theattached cablesfromview.
 1.
Bundle thecables together usingaband orother fastener (notprovided).
 Caution:
Donot bundle thepower cordtothe other cables. Otherwise, afire may occur.
 2.
Place thecable cover onthe projector asshown, guiding thecables through thenotch onthe base of
 the
cable cover.   
						

							

54
3.
Tighten bothcable cover screws.
 To
remove thecover, loosen bothscrews andpullthecover offofthe projector.
 Parent
topic:Setting Upthe Projector
 Installing
Batteriesinthe Remote Control
 The
remote controlusesthetwo AAbatteries thatcame withtheprojector.
 Caution:
Useonly thetype ofbatteries specified inthis manual. Donot install batteries ofdifferent types,
 or
mix new andoldbatteries.  
						

							

55
1.
Remove thebattery cover.
 2.
Insert thebatteries withthe+and –ends facing asshown.   
						

							

56
3.
Replace thebattery coverandpress itdown untilitclicks intoplace.
 Warning:
Disposeofused batteries according tolocal regulations. Donot expose batteries toheat
 or
flame. Keepbatteries outofthe reach ofchildren; theyarechoking hazards andarevery
 dangerous
ifswallowed.
 Parent
topic:Setting Upthe Projector  
						

							

57
Using
theProjector onaNetwork
 Follow
theinstructions inthese sections toset upyour projector foruse onanetwork.
 Wired
Network Projection
 Wireless
NetworkProjection
 Setting
UpProjector NetworkE-MailAlerts
 Selecting
OtherNetwork Settings
 Controlling
aNetworked ProjectorUsingaWeb Browser
 Crestron
RoomView Support
 Wired
Network Projection
 You
canproject through awired network. Todothis, youconnect theprojector toyour network, andthen
 set
upyour projector andcomputer fornetwork projection.
 After
connecting andsetting upthe projector asdescribed here,install thenetwork software fromthe
 included
CDordownload thesoftware andmanuals asnecessary.
 Note:
Ifyour projector isconnected viaaLAN cable toanetwork thatincludes awireless accesspoint,
 you
canconnect tothe projector wirelessly throughtheaccess pointusing theEpson network software.
 Connecting
toaWired Network
 Selecting
WiredNetwork Settings
 Parent
topic:UsingtheProjector onaNetwork
 Related
references
 Projector
NetworkSettings-Network Menu
 Connecting
toaWired Network
 To
connect theprojector toawired localareanetwork (LAN),usea100Base-TX or10Base-T network
 cable.
Toensure properdatatransmission, useaCategory 5shielded cableorbetter.
 1.
Connect oneendofthe network cabletoyour network hub,switch, orrouter. 
						

							

58
2.
Connect theother endofthe cable tothe projectors LANport.
 Parent
topic:WiredNetwork Projection
 Selecting
WiredNetwork Settings
 Before
youcanproject fromcomputers onyour network, youmust select thenetwork settingsforthe
 projector
usingitsmenu system.
 Note:
Makesureyoualready connected theprojector toyour wired network usingtheLAN port.
 1.
Turn onthe projector.
 2.
Press theMenu button.
 3.
Select theNetwork menuandpress Enter.  
						

							

59
4.
Select Network Configuration andpress Enter.
 5.
Select theBasic menuandpress Enter.
 6.
Select thefollowing basicoptions asnecessary:
 •
Projector Nameletsyou enter aname upto16 alphanumeric characterslongtoidentify the
 projector
overthenetwork.
 •
Remote Password letsyou enter apassword upto8alphanumeric characterslongforaccessing
 the
Remote inthe Epson WebControl. (Defaultusername isEPSONREMOTE ;default password
 is
guest .)
 •
Web Control Password letsyou enter apassword upto8alphanumeric characterslongfor
 accessing
theEpson WebControl. (Defaultusername isEPSONWEB ;default password is
 admin
.)
 •
Projector Keywordletsyou turn onasecurity password toprevent accesstothe projector by
 anyone
notinthe room withit.You must enter adisplayed, randomized keywordfromacomputer
 using
theEasyMP MultiPCProjection softwaretoaccess theprojector.
 Note:
Usethedisplayed keyboardtoenter thename, passwords andkeyword. Pressthearrow
 buttons
onthe remote controltohighlight characters andpress Enter toselect them. 
						

							

60
7.
Select theWired LANmenu andpress Enter.
 8.
Select yourIPSettings asnecessary:
 •
Ifyour network assignsaddresses automatically, turnonthe DHCP setting.
 •
Ifyou must setaddresses manually,turnoffDHCP andenter theprojectors IPAddress ,Subnet
 Mask
,and Gateway Addressasneeded.
 Note:
Tohighlight thenumbers youwant fromthedisplayed keyboard, pressthearrow buttons on
 the
remote control. Toselect ahighlighted number,pressEnter.
 9.
Toprevent displayofthe IPaddress onthe standby screen,turnoffIPAddress Display.
 10.
When youfinish selecting settings,selectComplete andfollow theon-screen instructions tosave
 your
settings andexitthemenus.
 Parent
topic:WiredNetwork Projection
 Wireless
NetworkProjection
 You
canproject overawireless network. Todothis, youmust setupyour projector andcomputer for
 wireless
projection.
 Note:
TheEpson 802.11b/g/n wirelessLANmodule isnot included withyour projector andisoptional.