Epson Projector PowerLite Pro G6870 User Manual

PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the
Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x
is a number from 0 to 255).
6. Enter a community name (PowerLite G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU). You can enter up to 32 single-byte alphanumeric...

4. Do one of the following:
• Select the Othersmenu and press Enter.
PowerLite Pro G6870/G6970WU
• Select the Administrator Setting menu and pressEnter.
PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
82 

5. If available, select the
Priority Gatewaysetting for your network.
6. If your network environment uses an AMX controller, turn on the AMX Device Discoverysetting to
allow the projector to be detected.
7. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView
setting to allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcast feature in the EasyMP
Monitor software.
8. If your network environment uses a Control4 or...

You see the Web Control screen.
Note:
If you connect from a web browser on a smartphone or tablet, a screen with two options is
displayed. Select remoteto display the Web Remote page, or select configto display the Web
Control page.
4. To select projector menu settings, select the name of the menu and follow the on-screen instructions.
5. To control projection remotely, select the Web Remoteoption.
You see a screen like this:
84  

1 Power on button control
2 Input source selection controls (some buttons may not be available depending on your
available projector ports)
3 Freeze button control
4 A/V Mute button control
5 Page Up andPage Down button controls
6 Closed caption control
7 Volume button controls
8 Source search control
9 Standby button control
6. Select the icon corresponding to the projector function you want to control.
Parent topic: Using the Projector on a Network
Related references
Projector Setup Settings - Extended...

Note:
If you want to use the Crestron RoomView system when the projector is turned off, you need to
adjust the Standby Mode settings in the Extended menu.
1. Press the Menubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
4. Select the Othersmenu (PowerLite Pro G6870/G6970WU) or the Administrator Settingmenu
(PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU) and press Enter.
PowerLite Pro G6870/G6970WU
86 

PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
5. Set the Crestron RoomView setting toOnto allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcasting feature in the
EasyMP Monitor software.
6. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
7. Turn off the projector, then turn it on again to enable the setting.
Parent topic: Crestron RoomView Support
Controlling...

You see this screen:
3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box.
4. To control projection remotely, click the on-screen buttons that correspond to the projectors remote control buttons. You can scroll through button options at the bottom of the screen.
Note: These on-screen buttons do not directly correspond to the projectors remote control buttons:
• OK acts as the Enterbutton
• Menu...

Using Basic Projector Features
Follow the instructions in these sections to use your projectors basic features.
Turning On the Projector
Turning Off the Projector
Selecting the Language for the Projector Menus
Resizing the Image with the Zoom Ring
Focusing the Image Using the Focus Ring
Setting the Lens Type
Setting the Screen Type
Adjusting the Image Position Using Screen Position
Adjusting the Image Position Using Lens Shift
Displaying a Test Pattern
Adjusting the Image Height
Image Shape
Remote...

1. Connect the power cord to the projectors power inlet.
2. Plug the power cord into an electrical outlet.
The projectors power light turns orange. This indicates that the projector is receiving power, but is
not yet turned on (it is in standby mode).
Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.
3. Press the power button on the projector or the Onbutton on the remote control to turn on the
projector.
The projector beeps and the power light flashes green as the...