Epson Projector PowerLite Home Cinema 3020/3020e User Manual

Setting Up the Projector21
When you connect an HDMI cable to the projector, it is recommended that you fasten it 
with the included cable clip. Follow these steps to install the cable clip:
1. Connect the HDMI cable to one of the HDMI ports on the projector.
2. Insert the end of the cable clip anchor into the cable clip hole near the HDMI port, as 
show below.
3. Place the open cable clip around the HDMI cable, but don’t lock it into place.
4. Slide the cable clip towards the projector and lock the clip...

22Setting Up the Projector
Making Other Connections
Connect the power cable and other cables described below, depending on how you plan to 
use the projector.
■Plug the power cable into the projector and a grounded electrical outlet.
■To use an AV controller with the projector, connect a 9-pin null modem serial cable to 
the 
RS-232C port.
■To connect to a digital camera, flash drive, or storage device, connect the USB cable that 
came with your device to both your device and to the projector’s USB port....

Setting Up the Projector23
Installing Batteries in the Remote Control
The remote control uses two AA batteries.
Warning: Keep batteries away from children. If a battery is swallowed, contact your doctor 
immediately.
1. Release the tab and lift open the cover.
2. Insert two new AA batteries as shown. 
3. Insert the tab on the cover and press it down until it clicks into 
place.
Aim the remote control at the screen, or at the front or back of the 
projector. Make sure you are within 32 feet (10 meters) of...

24Setting Up the Projector
2. Do one of the following:
■Plug the other end of the USB cable into the USB to AC adapter (PowerLite Home 
Cinema 3020 only), then connect the adapter to a wall outlet.
■Plug the other end of the USB cable into the 3D glasses charging port on the side of 
the WirelessHD Transmitter (PowerLite Home Cinema 3020e only).
■Plug the other end of the USB cable into the USB-A port on the back of the 
projector.
Note: The projector must be turned on to charge the 3D glasses through...

Setting Up the Projector25
■Plug the other end of the USB cable into a computer or other device with an available 
USB port.
Note: Epson does not guarantee the compatibility of the EPSON RF 3D active shutter glasses 
with computers or other devices.
Turning the Projector On and Off
Turning On the Projector
1. Remove the lens cap.
2. Turn on any connected equipment you plan to use.
3. Press the 
On button on the remote control or the 
Ppower button on the projector.
Note: To prevent children from turning...

26Setting Up the Projector
Turning Off the Projector
1. Turn off any equipment connected to the projector.
2. Press the Ppower button on the projector twice or press the 
Standby button on the 
remote control and wait for the light to stop flashing.
Caution: Turn off this product when not in use to prolong the life of the projector.
Selecting the Image Source
The source buttons on the projector and remote control let you switch between images from 
different pieces of equipment connected to the projector...

Setting Up the Projector27
Note: If an image does not appear, see “Problem Solving” on page 77.
To temporarily turn off the image and darken the screen, press the Blank button on the remote 
control. Press the Blank button again to return to normal viewing.
Positioning the Image
If the projector is not centered in front of the screen, use the horizontal keystone slider, 
horizontal keystone buttons, and vertical keystone buttons to correct the shape of the image.
Note: For the best image quality, try to...

28Setting Up the Projector
If one side of the image is taller than the other, make sure the projector is parallel to the 
screen. If necessary, adjust the front feet so that the projector is horizontal.
Your projector automatically adjusts images that are wider at the top or bottom, but if 
necessary, you can also use the vertical keystone buttons on the projector to correct this.
In addition to the horizontal keystone slider, you can use the volume buttons on the projector 
to adjust images that are...

Making Basic Adjustments29
Making Basic Adjustments
Follow the instructions in this chapter to make basic adjustments to the image shape, size, 
color, and quality. For further refinements, see “Making Detailed Adjustments” on page 42.
Focusing and Zooming
Use the focus ring to sharpen the image.
Use the zoom ring to reduce or enlarge the image.
Zoom ring
Focus ring 

30Making Basic Adjustments
Choosing the Aspect Ratio
In many cases, video signals are automatically resized to 
fit on your screen when 
Auto is selected as the Aspect 
setting. You may need to change the size of the image 
(or aspect ratio) for certain image types by pressing the 
Aspect button on the remote control.
Select one of these settings:
■Normal for standard TV broadcasts, computer 
images, or images with a 4:3 aspect ratio.
■Full for images recorded in 16:9 (wide-screen) format and squeeze...