Epson Projector PowerLite 99WH User Manual

1. If the device has a power button, turn off and unplug the device.
2. Disconnect the USB device or camera from the projector.
Parent topic:
Connecting to External USB Devices
Connecting to a Document Camera You can connect a document camera to your projector to project images viewed by the camera.
Depending on your Epson document camera model, do one of the following to connect the document
camera to your projector:
• For the Epson DC-06 document camera, locate the USB cable that came with the camera...

Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover.
2. Insert the batteries with the +and –ends facing as shown.
42   

3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
Related references
Remote Control Specifications
Opening the Lens Cover To open the projectors lens cover, slide the A/V Muteslide lever until it clicks into the open position....

Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
Wireless Network Projection
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Controlling a Networked Projector Using a Web Browser
Crestron RoomView Support
Wired Network Projection You can send images to your projector through a wired network (not supported on the PowerLite S27).
To do this, you connect the projector to your...

Selecting Wired Network Settings
Parent topic:
Using the Projector on a Network
Related references
Projector Network Settings - Network Menu
Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network
cable. To ensure proper data transmission, use a Category 5 shielded cable or better.
1. Connect one end of the network cable to your network hub, switch, or router.
2. Connect the other end of the cable to the projectors LANport.
Parent...

3. Select the
Networkmenu and press Enter.
4. Select Network Configuration and pressEnter.
5. Select the Basicmenu and press Enter.
6. Select the following basic options as necessary: •Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
46 

•
PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the
PJLink protocol for projector control.
• Web Control Password lets you enter a password up to 8 alphanumeric characters long for
accessing the projector over the web. (Default user name is EPSONWEB; default password is
admin.)
• Projector Keyword lets you turn on a security password to prevent access to the projector by
anyone not in the room with it. You must enter a displayed, randomized keyword from a...

• If you must set addresses manually, turn off
DHCPand enter the projectors IP Address,Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
10. To prevent display of the IP address on the standby screen, turn off IP Address Display.
11. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit...

• EasyMP Network Updater software (Windows only) allows you to update firmware for a projector over
a wired LAN. See the EasyMP Network Updater Operation Guide for instructions. You can download
the latest software and documentation from the Epson web site. Go to epson.com/support(U.S.) or
epson.ca/support (Canada) and select your projector.
• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app; visit epson.com/projectorapp (U.S.) orepson.ca/projectorapp...

1. Remove the wireless LAN module cover screw.
2. Insert the wireless LAN module into the
USB-Aport.
50