Epson Projector Powerlite 460 User Manual

							Using the Projector on a Network91
Using the EasyMP Software
Once you’ve set up your projector and computer for network 
projection, see the EasyMP Network Projection Operation Guide for 
instructions on the following EasyMP features:
■Starting EasyMP Network Projection
■Projecting over the network (content over IP)
■Multi-screen projection
■Using Presentation mode
■Connecting to a projector on a different subnet
Using Projector E-mail Alerts
When this feature is enabled, the projector sends you an e-mail alert if 
it has any problems. 
1. Press the 
Menu button on the remote control, select the 
Network menu, then press Enter. 
2. Choose 
Network Configuration and press Enter. 
3. Choose 
Mail, then press Enter. You see the following screen: 
4. Highlight 
On to receive email notifications, then press Enter.
5. Press 
Esc to return to the previous menu. 
						

							92Using the Projector on a Network6. Enter the IP address for the SMTP server for the projector.
You can enter a number from 0 to 255 in each field of the address. 
However, the following IP addresses cannot be used: 127.x.x.x, 
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
7. Enter the SMTP server’s port number. The default value is 25. 
You can enter a numeric value from 1 to 65535.
8. Choose one of the 
Address fields, then enter the e-mail address 
and the contents of the message that you will receive when a 
problem or warning occurs. You can register up to three addresses. 
You can enter up to 32 alphanumeric characters for the e-mail 
address.
When the selected problem or warning occurs, an e-mail message is 
sent to the specified notification addresses. The subject line of the 
e-mail is 
EPSON Projector. 
The e-mail includes the following information:
■Line 1: The name of the projector where the problem has 
occurred
■Line 2: The IP address of the projector where the problem has 
occurred
■Line 3: Details of the problem 
Using SNMP to Monitor the Projector
Network administrators can use SNMP (Simple Network 
Management Protocol) to monitor projectors. 
1. Press the 
Menu button on the remote control, select the 
Network menu, then press Enter. 
2. Choose 
Network Configuration and press Enter. 
note
If a critical problem develops 
with a projector which 
causes it to suddenly stop 
working, it may not be 
possible for the projector to 
send a message.
If Standby Mode is set to 
Communication ON in 
the Extended menu, the 
projector can still be 
monitored even if the 
projector is in standby mode 
(when the power is off).
note
If you’re a network 
administrator, you can use 
the SNMP option to enter a 
t r a p  I P  a d d r e s s .  T h i s  l e t s  y o u  
receive trap alerts for the 
projectors you’re monitoring. 
						

							Using the Projector on a Network93
3. Choose Others, then press Enter. You see the following screen: 
4. Turn on the SNMP setting.
5. Enter up to two IP addresses for notification.
You can enter a number from 0 to 255 in each field of the address. 
However, the following IP addresses cannot be used: 127.x.x.x, 
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
6. For 
Priority Gateway, select Wired or Wireless.
7. If your network environment uses an AMX controller, select 
ON 
to allow the projector to be detected by AMX Device Discovery. 
						

							94Using the Projector on a Network
Using a Browser to Control the Projector
You can use a standard web browser to monitor and control the 
projector through the network. Because you can use your computer’s 
keyboard, you may find it easier to make network settings using your 
browser than using the projector’s remote control.
1. Make sure the projector is set up for your network, as described 
on page 76. (Standby Mode in the Extended menu should be set 
to 
Communication On to monitor the projector in standby 
mode.) When using a browser to access the projector, you cannot 
connect through a proxy server.
2. Open your web browser and enter the IP address of the projector 
you want to monitor in the browser window. 
If you’re not sure what the address of the projector is, turn the 
projector on and select 
Net. Info.-Wired LAN or Net. 
Info.-Wireless LAN
 from the Network menu to display the IP 
address of the projector. Do not enter leading zeroes.
3. Press 
Enter, or, if you set a Web control password in the 
projector’s Network menu, enter your user name and password, 
then press 
Enter. You see a screen like the following: 
						

							Using the Projector on a Network95
4. Select one of the menu options listed on the screen, then change 
any of the settings as needed. These settings correspond to those 
found in the projector’s menu system.
You cannot change the following settings using a web browser:
■Pointer Shape, Pattern, or User Button in the Settings 
menu
■User’s Logo, High Altitude Mode, and Language in the 
Extended menu
■Reset All and Reset Lamp Hours in the Reset menu
■Password protection
Using Web Remote Control
When you access the projector through your browser, you can display 
a “virtual remote control” on your computer screen. This lets you 
change sources and perform many of the same functions as you can 
with the physical remote control.
From the Projector Control menu, select 
Web Remote. You see the 
following screen:
■The Power button turns the projector on and off.
■The Search button searches for signal sources (see page 28).
Source Search 
button
USB button LAN button
Volume buttons Computer button
Video button
A/V Mute button
Pause button Power button
Page-up/down 
buttonsClosed captioning 
button 
						

							96Using the Projector on a Network
■The Computer button selects a computer signal (connected to the 
Computer1 or Computer2 port).
■The Video button selects a video signal (connected to the Video 
or 
S-Video port).
■The LAN button selects a network signal or wireless signal (using 
the optional wireless unit).
■The USB button selects USB computer display (see page 44) or a 
signal from equipment connected to the 
TypeA  (flat) USB 
port, such as a document camera (see page 57).
■The Pause button stops the image (see page 35).
■A/V Mute button temporarily turns off the picture and sound (see 
page 34).
■The Page Up/Down buttons control PowerPoint slides (requires 
USB cable. See page 38).
■The Volume buttons raise or lower the audio volume.
■The CC (Closed Captioning) button lets you display closed 
captioning for content that provides it. 
						

							97
4
Maintaining the Projector
Your projector needs little maintenance. All you have to do on a 
regular basis is clean the lens, and check that the air filter and vents are 
clean. A clogged air filter or vent can block ventilation needed to cool 
the projector.
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■Cleaning the projection window
■Cleaning the projector case
■Cleaning the air filter
■Replacing the air filter
■Replacing the lamp
■Replacing the remote control batteries
■Transporting the projector
warning
Before you clean any part of 
the projector, turn it off and 
unplug the power cord. 
Never open any cover on the 
projector, except the lamp 
cover. Dangerous electrical 
voltages in the projector can 
injure you severely. Do not 
try to service this product 
yourself, except as specifically 
explained in this User’s 
Guide. Refer all other 
servicing to qualified service 
personnel. 
						

							98Maintaining the Projector
Cleaning the Projection Window
Clean the projection window whenever you notice dirt or dust on the 
surface.
To remove dirt or smears on the window, use a commercially available 
cloth for cleaning glasses.
Cleaning the Projector Case
Before cleaning, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free 
cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water 
and a neutral detergent and firmly wring the cloth dry. Then wipe 
the case.
caution
Do not rub the projection 
window with harsh 
materials or subject it to 
shocks, or you may damage 
the window.
Do not use wax, alcohol, 
benzene, paint thinner, or 
other chemical detergents. 
These can damage the case. 
						

							Maintaining the Projector99
Cleaning the Air Filter 
Your projector includes an air filter to ensure the best performance 
and help protect your equipment investment. If dust collects on the 
air filter, clean it as described here. Dust clogs prevent proper 
ventilation and can cause overheating, which can damage the 
projector.
1. Turn off the projector.
2. Remove dust from the air filter using a small vacuum cleaner 
designed for computer or office equipment, or gently clean the 
vent with a soft brush (such as an artist’s paintbrush).
You can remove the air filter to clean both sides.
If the filter is too dirty or broken, replace the filter as described below. 
Replacing the Air Filter
You need to replace the air filter if:
■You cannot remove the dust from it
■The air filter is damaged or torn
■You repeatedly see a projected message telling you to clean or 
replace it
note
To order replacement air 
filters, request part number 
V13H134A27. See page 19 
for ordering information. 
						

							100Maintaining the ProjectorContact your dealer or call Epson at 800-GO-EPSON 
(800-463-7766) to obtain a new air filter. Request part number 
V13H134A27.
1. Turn off the projector and unplug the power cord.
2. Slide the switch, then open the air filter cover on the side of the 
projector.
3. Grasp the tab and pull the air filter straight out as shown.
note
Air filters contain 
polycarbonate, ABS resin, 
and polyurethane foam. 
Dispose of used air filters 
according to local 
regulations.