Epson Projector Powerlite 1725 User Manual

Setting Up Network Projection91
■If your network assigns addresses automatically, turn on the 
DHCP setting.
■If your network does not assign addresses automatically, turn 
off 
DHCP and enter the projector’s IP Address, Subnet 
Mask
, and Gateway Address, as needed. 
To enter numbers, use the  buttons on the remote 
control to highlight the number you want to input, then press 
the 
Enter button. When you’re finished changing an address 
in the network menu, highlight 
Return, then press the Enter...

92Setting Up Network Projection3. Choose 
Mail, then press Enter. You see the following screen: 
4. Highlight 
On to receive email notifications, then press Enter.
5. Enter the IP address for the SMTP server for the projector.
You can enter a number from 0 to 255 in each field of the address. 
However, the following IP addresses cannot be used: 127.x.x.x, 
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
6. Enter the SMTP server’s port number. The default value is 25. 
You can enter a...

Setting Up Network Projection93
■Line 2: The IP address of the projector where the problem has 
occurred
■Line 3: Details of the problem 
Using SNMP to Monitor the Projector
Network administrators can use SNMP (Simple Network 
Management Protocol) to monitor projectors. 
1. Press the 
Menu button on the remote control, select the 
Network menu, then press Enter. 
2. Choose 
Network Configuration and press Enter. 
3. Choose 
Others, then press Enter. You see the following screen: 
note
If you’re a network...

94Setting Up Network Projection4. Enter up to two IP addresses for notification.
You can enter a number from 0 to 255 in each field of the address. 
However, the following IP addresses cannot be used: 127.x.x.x, 
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
5. If your network environment uses an AMX controller, select ON 
to allow the projector to be detected by AMX Device Discovery.
Connecting With Windows Vista
If you have Windows Vista, you can use the Network Projector 
function...

Setting Up Network Projection95
3. From the Start menu on your computer, select All Programs, 
Accessories, then Connect to a Network Projector. You see 
this screen:
4. You can select the projector automatically or manually:
■To let your computer search automatically for the projector, 
select 
Search for a projector. You see this screen:
After locating the connected projectors, your computer lists 
them on the screen. Select the one you want and then click 
Connect. 

96Setting Up Network Projection
■To locate the projector by IP address, select Enter the 
projector address
. You see this screen:
Enter the IP address for the projector in the format shown. 
Enter a password for the projector if one has been set. Then 
click 
Connect.
5. If you need to pause your presentation, press the 
Pause button. 
Click 
Resume when you are ready to continue.
6. When you want to disconnect from the projector, click the 
Disconnect button.
Vista Network Projector Limitations
When...

97
5
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image, 
sound, and other features. This chapter covers the following 
information: 
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Using the projector security features
■Customizing power and operation
■Multi-screen color adjustment 

98Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to 
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the 
Menu button on the 
remote control or on the projector. 
You see a menu screen similar to the one below: 
The menus are listed on the left and the options available for the 
highlighted menu are shown on the right.
2. Use the  pointer button on the remote control (or the 
navigational...

Fine-Tuning the Projector99
4. After highlighting the option you want to adjust, use the 
pointer button to change the setting. In some cases, you may 
have to press the 
Enter button to view a sub-screen for changing 
the setting. 
■Press the left or right side of the  pointer button to adjust
a slider bar.
■To select from two or more settings, use the  pointer 
button to highlight the desired setting and press 
Enter. 
5. After changing the settings, press the 
Esc button to save your 
changes and...

100Fine-Tuning the Projector
Adjusting the Image 
You can use the Image menu to adjust the brightness, sharpness, color, 
tint, and contrast. 
1. Press the 
Menu button on the projector or remote control and 
select the 
Image menu. You see the Image menu screen. 
2. Use the  pointer button to highlight the desired option, then 
adjust it as needed:
■Color Mode
Lets you quickly adjust the color and brightness for various 
uses. You can save a different setting for each source. See 
page 33 for details on...