Epson Projector Powerlite 1720 Quickstart Guide

							
Before using the projector, make sure you read the safety instructions in 
the User’s Guide on your projector CD.
1   Locate the required cables:
 
2   Connect the computer cable to  
the blue Computer (Component Video) 
port on the projector.
3   Connect the other end to your notebook’s  
video-out ormonitor port.
4   Connect the power cord to the 
projector, then plug the other end 
into an electrical outlet.
1   Turn on your notebook.
2   Open the A/V Mute slide (lens cover).
      NOTE: The slide must be 
opened completely.
3    Make sure the Power light 
is orange and not flashing.
4   Press thePower button 
to turn on the projector.
   The projector beeps once, 
and the Power light flashes 
green and then stays on.
STA
R
T
 HERE
 
Turn on your equipment
Connect the projector
   to your notebook
Follow these instructions to connect the projector to your 
notebook. For other setup options, see your User’s Guide.
PowerLite
®
 1720/1730W
Quick Setup
VGA computer cable
1   If you’ve turned on your notebook and switched it to external display, 
but you don’t see an image, press the Source Search button on the 
projector or the Search button on the remote control to select the 
image source. 
 NOTE: If you still see a blank screen or have other display problems, 
see the troubleshooting tips on the back of this sheet.
 
2 To raise the image, press 
  the foot release button    
 for the front adjustable   
 foot and lift the front.   
 Release the button to  
 lock the foot in position. 
3 Turn the focus ring to sharpen the image. 
 
  Turn the zoom ring to reduce or 
 enlarge the image.
 
4   If your image looks likeor, you’ve placed the projector off  
to one side of the screen at an angle. Place it directly in front of the 
center of the screen, facing the screen squarely. 
5   If your image looks likeor, press theorbutton  
on the projector to correct it.
Adjust the image
To shut down the projector, press thePower button twice and  
simply unplug it. You don’t have to wait for the projector to cool off.
Turn over
Power light
Power button
Zoom
Focus
Power cord
*411482100**411482100*
4114821	 Rev.0
1-F	 	 C
4114821	 Rev.0
1-F	 	 M
4114821	 Rev.0
1-F	 	 Y
4114821	 Rev.0
1-F	 	 K 
						

							
If this is your first time using the remote, make sure its batteries 
are installed as shown (two AA batteries).
You can use the remote control to operate the projector. With the USB 
cable, you can also use the remote to change presentation slides. For more 
information on using the remote control, see your User’s Guide.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice. 
© 2008 Epson America, Inc. 5/08 
Printed in XXXXXX
Quick Setup
PowerLite 1720/1730W
CPD-25570
Using the remote control
Where to get help
For more information about using the projector, install the User’s Guide 
from your projector CD.
Telephone Support Services 
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter 
the PIN on the Epson PrivateLine Support card included with your projector. 
This service is available 6 AM to 6 PM, Pacific Time, Monday through  
Friday, for the duration of your warranty period. You may also speak with  
a projector support specialist by dialing one of these numbers:
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday  
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long 
distance charges may apply.
Internet Support 
Visit Epson’s support website at epson.com/support and select your 
product for solutions to common problems. You can download utilities and 
documentation, get FAQs and troubleshooting advice, or e-mail Epson with 
your questions.
Visit http://www.presentersonline.com to access tips, templates, and 
training for developing successful presentations.
If you see a blank screen...
If you see a blank screen or the No signal message after turning on 
your notebook, check the following:
     Make sure the Power light on the projector is green and not flashing, 
and the A/V Mute slide is open.
     Press the Source Search button on the projector or the Search button 
on the remote control to select the computer as the image source.
     Press the function key on your keyboard that lets you display on an 
external monitor. It may be labeled CRT/LCD or have an icon such as
. You may have to hold down the Fn key on the notebook while 
pressing it. Allow a few seconds for the projector to sync up after 
changing the setting.
If the projector and notebook 
don’t display an image...
If your image displays either on the projector or notebook, but not on 
both, follow the steps below. Note that some notebooks cannot display 
the same resolution and/or aspect ratio on both the LCD screen and the 
projected image.
Windows 
Try using the CRT/LCD orkey as described above. On most systems, 
this key lets you toggle between the LCD screen and the projector, 
or display on both at the same time.
If that doesn’t work, check your monitor settings to make sure both the 
LCD screen and the external monitor port are enabled.
1.    From the Windows® Control Panel, open the Display utility. In 
Windows Vista®, right-click on the desktop and select Personalize, 
then select Display Settings.
2.   In the Display Properties dialog box, click 
the Settings tab, then click Advanced. In 
Windows Vista, click Advanced Settings.
3.   The method for adjusting the setting varies; 
you may have to click a Monitor tab, then 
make sure the external Monitor port is set 
as your primary display and/or enabled. 
See your notebook’s manual or online help 
for details.
Mac OS® X
1.   From the Apple® menu, select System 
Preferences, then select Display 
or Displays.
2.   Click Detect Displays.
3.   Select the VGA Display or Color LCD 
dialog box.
4.   Click the Arrangement or Arrange tab 
and click Mirror Displays.
 
Troubleshooting
Turn off projector 
display and sound
Display next or 
previous slide
Navigate projector menus
Control projector volume
Register today to get product updates, special promotions, and 
customer-only offers. You can use the registration card or CD included 
with your projector, or register online at www.epson.com/webreg.
Turn projector on 
and offChoose which source 
to display
Change aspect ratio
Access projector 
menu system
4114821	 Rev.0
1-B	 	 C
4114821	 Rev.0
1-B	 	 M
4114821	 Rev.0
1-B	 	 Y
4114821	 Rev.0
1-B	 	 K