Epson Projector Powerlite 1260 User Manual

							81
5
Maintaining the Projector
Your projector needs little maintenance. All you have to do on a 
regular basis is clean the lens, and check that the air filter and vents are 
clean. A clogged air filter or vent can block ventilation needed to cool 
the projector.
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■Cleaning the lens
■Cleaning the projector case
■Cleaning the air filter
■Replacing the air filter
■Replacing the lamp
■Replacing the remote control batteries
■Transporting the projector
warning
Before you clean any part of 
the projector, turn it off and 
unplug the power cord. 
Never open any cover on the 
projector, except the lamp 
cover. Dangerous electrical 
voltages in the projector can 
injure you severely. Do not 
try to service this product 
yourself, except as specifically 
explained in this User’s 
Guide. Refer all other 
servicing to qualified service 
personnel. 
						

							82Maintaining the Projector
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
To remove dirt or smears on the lens, use a commercially available 
cloth for cleaning glasses.
Cleaning the Projector Case
Before cleaning, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free 
cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water 
and a neutral detergent and firmly wring the cloth dry. Then wipe 
the case.
Cleaning the Air Filter 
Your projector includes an air filter to ensure the best performance. If 
dust collects on the air filter, clean it as described here. Dust clogs 
prevent proper ventilation and can cause overheating, which can 
damage the projector.
1. Turn off the projector and unplug the power cord.
2. Remove dust from the air filter using a small vacuum cleaner 
designed for computer or office equipment, or gently clean the 
vent with a soft brush (such as an artist’s paintbrush).
caution
Do not rub the lens with 
harsh materials or subject 
the lens to shocks, or you 
may damage it.
Do not use wax, alcohol, 
benzene, paint thinner, or 
other chemical detergents. 
These can damage the case.
note
To order replacement air 
filters, request part number 
V13H134A25. See page 17 
for ordering information. 
						

							Maintaining the Projector83
You can remove the air filter to clean both sides.
If the filter is too dirty or broken, replace the filter as described below. 
Replacing the Air Filter
You need to replace the air filter if:
■You cannot remove the dust from it
■The air filter is damaged or torn
■You repeatedly see a projected message telling you to clean or 
replace it
1. Turn off the projector and unplug the power cord.
2. Open the air filter cover on the side of the projector.
3. Lift the air filter out of its slot as shown.
note
To order replacement air 
filters, request part number 
V13H134A25. See page 17 
for ordering information.
note
Air filters contain 
polycarbonate, ABS resin, 
and polyurethane foam. 
Dispose of used air filters 
according to local 
regulations. 
						

							84Maintaining the Projector4. Slide the new air filter into the slot until it clicks into place.
5. Close the air filter cover.
Replacing the Lamp
The life span of the projection lamp is about 4,000 hours if Power 
Consumption 
in the Settings menu is Normal (default), and 5,000 
hours if this setting is 
ECO. See page 88 to check the lamp usage.
It is time to replace the lamp when: 
■The projected image gets darker or starts to deteriorate.
■The message Replace the lamp appears on the screen and the 
Lamp light flashes orange. To maintain projector brightness 
and image quality, replace the lamp as soon as possible.
note
Turn off this product when 
not in use to prolong the life 
of the projector.  
						

							Maintaining the Projector85
You may also need to replace the lamp if the Lamp light flashes 
red. See page 93.
Contact your dealer or call Epson at 800-GO-EPSON 
(800-463-7766). Request part number V13H010L58.
Follow these steps to replace the lamp:
1. Turn off the projector and unplug the power cord.
2. Let the projector cool for at least an hour (if it has been on). The 
lamp is extremely hot immediately after use. 
3. Loosen the lamp cover screw (you cannot remove it). Then slide 
the lamp cover off.
Lamp 
light
warning
Let the lamp cool fully 
before replacing it. 
In the unlikely event that 
the lamp has broken, small 
glass fragments may be 
present and should be 
removed carefully to avoid 
injury. If the projector has 
been installed on the ceiling, 
you should stand to the side 
of the lamp cover, not 
underneath it.
If the lamp is used after the 
replacement period has 
passed, the possibility that 
the lamp may break 
increases. When a lamp 
replacement message 
appears, replace the lamp 
with a new one as soon as 
possible, even if it is still 
working. 
						

							86Maintaining the Projector4. Loosen the two screws holding the lamp in place (you can’t 
remove them).
5. Hold the lamp as shown and pull it straight out.
 
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is 
facing the right way.) Then tighten its screws.
Loosen, but don’t 
remove these screws
note
The lamp(s) in this 
product contain mercury. 
Please consult your state and 
local regulations regarding 
disposal or recycling. Do not 
put in the trash. 
						

							Maintaining the Projector87
7. Replace the lamp cover, then tighten its screw.
8. Reset the lamp timer as described in the next section. 
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the 
projector’s menu system. 
1. Press the 
Menu button on the remote control or on the 
projector’s control panel. You see the main menu.
2. Select the 
Reset menu and press Enter. You see this screen:
3. Select 
Reset Lamp Hours and press Enter. 
4. When you see the prompt, select
 Yes and press Enter.
5. When you’re finished, press 
Menu to exit.
note
Tighten the lamp cover 
securely so you do not receive 
a lamp cover error when you 
turn the projector back on. 
						

							88Maintaining the Projector
Checking Lamp Usage 
To check the number of hours the lamp has been used, press the 
Menu button and highlight the Info menu. You see a screen like this:
The life span of the lamp is about 4,000 hours if 
Power 
Consumption
 in the Settings menu is Normal (default), and 5,000 
hours if this setting is 
ECO. Make sure you have a spare lamp handy if 
the usage hours on this menu are close to the life span of your lamp.
Replacing the Remote Control Batteries
Replace the batteries in the remote as described below: 
1. Turn the remote control over.
2. Press in on the catch on the battery cover as you lift the cover off.
note
The information displayed 
depends on the input signal 
currently selected.
If you have used the 
projector for less than 
10 hours, the hours are 
listed as 0H.
caution
When replacing batteries, 
take the following 
precautions:
■Replace the batteries as 
soon as they run out. If the 
batteries leak, wipe away 
battery fluid with a soft 
cloth. If fluid gets on your 
hands, wash immediately.
■Do not expose batteries to 
heat or flame.
■Dispose of used batteries 
according to local 
regulations.
■Do not use batteries other 
than those specified in this 
User’s Guide and do not 
use batteries of different 
types or mix old and new 
batteries.
■Keep these batteries out of 
the reach of children. 
Batteries are choking 
hazards and are very 
dangerous if swallowed. 
						

							Maintaining the Projector89
3. Install two AA alkaline batteries, inserting the +and– ends as 
shown.
4. Replace the battery cover and press it down until it clicks into 
place.
Transporting the Projector
The projector contains many glass and precision parts. When 
hand-carrying the projector, use the carrying case.
Follow these guidelines to prevent damage when transporting it: 
■Close the A/V Mute slide (lens cover).
■If a USB device is connected, remove it from the projector.
■Return the projector feet to their stored (highest) positions.
■When shipping the projector for repairs, use the original 
packaging material if possible. If you do not have the original 
packaging, use equivalent materials, placing plenty of cushioning 
around the projector.
■When transporting the projector a long distance, first place it in a 
hard-shell shipping case, then pack it in a firm box with 
cushioning around the case. 
note
Epson shall not be liable for 
any damages incurred 
during transportation. 
						

							90Maintaining the Projector